Make pre-order

(1)
average
cm: 19.2 w x 32 d x 9.7 h
in: 7.559 w x 12.598 d x 3.819 h
2
BUY FOR  $16.99

Source Files

|

Description

|

Printing Details

This 3D model consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Version 1 and Version 2 are the files for Naboo N-1 Starfighter 3D Model optimized for 3D printing, the preview pictures of which you see above.

It is recommended:

  • to print Version 1 STL files on FDM/FFF 3D printers;
  • to print Version 2 STL files on DLP/SLA/SLS 3D printers.
File Name File Size Time / Filament
1_hull_sls (repaired).stl
47.43 MiB 5 h 42 min
3 m
Download
2_luke_sls (repaired).stl
3.73 MiB 12 min
<1 m
Download
3_platform_sls (repaired) .stl
1.57 MiB 1 h 41 min
1 m
Download

HISTORY OF THE NABOO STARFIGHTER
 The N-1 Starfighter was originally built by the Naboo, and was most notably used during the Trade Federation invasion of the planet. During the invasion, the pilots of Bravo Flight flew the N-1 during the final assault against the Droid Control Ship the Saak'ak. Young Anakin Skywalker fired his torpedoes into its main reactor, effectively destroying it from within. They later joined in the celebration on the planet below, flying overhead Naboo's capital of Theed.
 10 years later, the N-1 was used to escort Senator Padmé Amidala to Coruscant in order to vote on the Military Creation Act. Their Royal Starship held a decoy senator, and Amidala flew in one of the starfighters. They landed without incident, but the bounty hunter Zam Wesell hit the ship shortly after, destroying it and killing the senator's double. N-1s remained in Naboo service during the Clone Wars, with several being kept in Theed Hangar during this time.
 Years later, following the climactic Battle of Endor, N-1 Starfighters flew in celebration after the Galactic Empire's second Death Star was destroyed. Shortly thereafter, Imperial agents received posthumous orders from Emperor Palpatine to commence the destruction of Naboo via weather manipulation as part of Operation: Cinder. Rebel leader Leia Organa, ace pilot Shara Bey and Naboo's own Queen Soruna flew the long-abandoned N-1 fighters in the Theed Hangar into space to destroy the Imperial satellites that were causing the extreme weather conditions.

ABOUT THIS 3D MODEL

The model is saved in STL files, a format supported by most 3D printers

FDM version contain 20 parts. The pilot's cabin is made with maximum detailed. And with the opening cab cover, which you can print with a transparent plastic, so you will have full detalization of the ship as in the universe of Space Wars. All fastenings are made with connectors. You can put your ship on a special platform which was designed for this model. To make it comfortably stand on your surface.
SLS version same as FDM but smaller and made as 3 parts, for economy your material.

All .STL files for 3D printing have been checked in Netfabb no errors were shown.

Note: Before starting 3D printing the model, read the Printing Details for CURA 2.7.0. Software.

There are 20 parts for FDM version and 3 parts for SLS.

All parts of connectors should be printed at 100% infill.

Scale: 
Its length in Space Wars universe is 11 meters. Model made as 1/35 scale in FDM version and 1/70 in SLS/SLA version.

FDM version:
- After being printed will stand 97 mm tall, 192 mm wide, 320 mm length;
- Connectors should be printed at 100% infill to make them solid.
SLS/SLA version:
- After being printed will stand 48 mm tall, 96 mm wide, 159 mm length.
- Has few details to keep printing costs down.

WHAT WILL YOU GET AFTER PURCHASE?

- .STL files of Naboo N - 1 Starfighter for printing which consist of 23 parts.
- High-poly detailed model of this ship.
- 2 versions of files for this model for FFF/FDM and SLS/SLA.
- Made in scale 1/35 and 1/70 of Its real size. 
- Detailed settings that we provide for Cura 2.7.0 for the best print.
- Full technical support from the Gambody Support Team.

Watch the tutorial video on how to assemble SpaceWar Naboo N - 1 Starfighter 3D Printing Miniature at Gambody YouTube channel

You can get Space War Naboo N - 1 Starfighter 3D Printing Model right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Also you may like another Space War 3D models of ships.

_______
FAQ: 

Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 2.7.0. and printed on an Ultimaker 2 in PLA material.

Note: To maintain model quality, do not try to increase or decrease the size, since the connectors may not fit and the model will not be assemble after scale changes.

To avoid printing problems, we recommend the following settings:

Quality 
Layer Height: 0.1 mm
Initial Layer Height: 0.27 mm
Line Width: 0.35 mm
Wall Line Width: 0.35 mm
   Outer Wall Line Width: 0.35 mm
   Inner Wall(s) Line Width: 0.35 mm
   Top/Bottom Line Width: 0.35 mm
   Infill Line Width: 0.35 mm
   Skirt/Brim Line Width: 0.35 mm
   Support Line Width: 0.35 mm
 Initial Layer Line Width: 100%

Shell 
Wall Thickness: 1.05 mm
Wall Line Count: 3
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0.025 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Shortest
Ignore Small Z Gaps: Check

Infill 
Infill Density: 20% (all parts of the connectors should be printed at 100% infill)
Infill Line Distance: 3.5 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill Overlap Percentage: 10%
    Infill Overlap: 0.035 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.0175 mm
Infill Wipe Distance: 0.0875 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2

Material 
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.7 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 20 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Speed 
Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 36 mm/s
      Outer Wall Speed: 26 mm/s
      Inner Wall Speed: 36 mm/s
    Top/Bottom Speed 20 mm/s
    Support Speed: 26 mm/s
      Support Infill Speed: 26 mm/s
Travel Speed: 90 mm/s
Initial Layer Speed: 27 mm/s

    Initial Layer Print Speed: 27 mm/s
    Initial Layer Travel Speed: 54 mm/s
Skirt/Brim Speed: 27 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Travel 
Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.6562 mm 

Cooling 
Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.27 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Support 
Enable Support: Check
Support Placement: Everywhere
Support Overhang Angle: 50°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 2.3333 mm
Support Z Distance: 0.1 mm
    Support Top Distance: 0.1 mm
    Support Bottom Distance: 0.1 mm
Support X/Y Distance: 0.7 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.2 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 23 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Experimental 
Extra Skin Wall Count: 0

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Comments

comments powered by Disqus

Similar items

Browse more newly listed 3D printings