Black Panther 3D Printing Figurine | Assembly

HISTORY OF THE BLACK PANTHER 

T'Challa was born in Wakanda, a country located in Africa with the reigning monarch T'Chaka and his wife Ramonda. He was taught most of his life so that he took his father's place as the next "Black Panther". T'Challa became a man with a very active mind and despite all the efforts of T'Chaka he had a great dislike for politics. In 2009, a week after he became a defender of Wakida, T'Challa, as a Black Panther, was sent with Okoye to rescue hostages from Wakanda from Zanda and Douglas Scott. T'Challa was the prince of the developed African country Wakid. When the United Nations decided to establish the Sokovia agreement to control the Avengers, T'Challa and his father T'Chaka went to Vienna. They met there a member of the Avengers Natalia Romanov. During the conference, there was an act of terrorism that killed T'Chaka. As the heir of T'Challa, he became king and inherited from his father the Mantle of the Black Panther. As soon as T'Challa found evidence that the terrorist act was organized by none other than James Barnes, also known as the Winter Soldier, he donned a Black Panther suit and set off to take revenge. T'Challa followed Barnes to Bucharest where he encountered Captain America and Falcon trying to protect him. They fought until the police stopped them. The police detained Barnes, Rogers, and Wilson because they did not sign the Sokowian agreement. The Avengers went to sign the treaty and Barnes was locked up in jail.

ABOUT THIS 3D MINIATURE

Black Panther 3D Miniature for printing was created in ZBrush. The model is saved in STL files, a format supported by most 3D printers. 

FDM version features:

- Contain 9 parts;

- Made with Locks. One part of Lock (2_Ge_lock_7S (x11)) you need to print 11 times;

- Made with a platform that is stylized under Wakanda nature;

- All parts are divided in such way that you will print them with the smallest amount of supports.

SLS/SLA version features:

- Same as FDM but smaller and made as 1 piece.

All STL files for 3D printing have been checked in Netfabb and no errors were shown.

Note: Before starting 3D printing the model, read the Printing Details for CURA 3.1.0. Software.

There are 9 parts for FFF/FDM version and 1 part for SLS/SLA version.

Scale: His tall in life is 1820. Model made as 1/8 scale in FDM version and 1/16 in SLS/SLA version.

FDM version dimensions:

After being printed will stand:
 156 mm tall, 216 mm wide, 154 mm deep - with platform;

SLS/SLA version dimensions:

After being printed will stand:
 78 mm tall, 108 mm wide, 77 mm deep - with platform;

- Has only 1 detail, to keep printing costs down.

WHAT WILL YOU GET AFTER PURCHASE?

- STL files of Black Panther for 3D printing which consist of 10 parts;

- 2 versions of files for this model for FFF/FDM and SLS/SLA;

- Removable platform that is stylized under the Wakanda nature;

- High-poly detailed miniature of Black Panther;

- Detailed settings that we provide for Cura 3.1.0. for the best print;

- Full technical support from the Gambody Support Team.

Watch the tutorial video on how to assemble Black Panther 3D Printing Miniature at Gambody YouTube channel.  

You can get Model of Black Panther for 3D Printing right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Also, you may like other Marvel 3D Printing Figurines as well as 3D Figurines of DC.

_______
FAQ: 
Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

Generic

This model was tested in Cura 3.1.0. and printed on an Ultimaker 2 in PLA material.

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

To avoid printing problems, we recommend the following settings:

Quality

Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Slicing Tolerance: Middle
Line Width: 0.4 mm
Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
   Top/Bottom Line Width: 0.4 mm
   Infill Line Width: 0.4 mm
   Skirt/Brim Line Width: 0.4 mm
   Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Shell 

Wall Thickness: 0.8 mm
Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill 

Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Material 

Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Speed 

Print Speed: 45 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s
      Support Infill Speed: 45 mm/s
Travel Speed: 80 mm/s
Initial Layer Speed: 15 mm/s

    Initial Layer Print Speed: 15 mm/s
    Initial Layer Travel Speed: 26.6667 mm/s
Skirt/Brim Speed: 15 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Travel 

Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm 
Cooling 
Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Support 

Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 1.3333 mm
Support Z Distance: 0.3 mm
    Support Top Distance: 0.3 mm
    Support Bottom Distance: 0.3 mm
Support X/Y Distance: 0.7 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.2 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 

Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 18 
Brim Only on Outside: Check

Mesh Fixes 

Union Overlapping Volumes: Check
Maximum Resolution: 0.01 mm
Merged Meshes Overlap: 0.15 mm

Special Modes

Print Sequence: All at Once
Surface Mode: Normal

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.