Premium Stock

Toruk 3D Printing Figurine | Assembly

cm: 62.9 w x 39.2 d x 18.2 h
in: 24.764 w x 15.433 d x 7.165 h

Source Files




Printing Details

This 3D Figurine consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Toruk 3D printing figurine comes in 4 versions for each 3D printer type (FFF/FDM, DLP/SLA and SLS). Files for each version are available for download after the purchase.

Detailed information about this 3D printing figurine is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
2_crest_top_FDM(repaired) .stl
6.67 MiB 37 min <1 m 9 x 45 x 31 Download
3_crest_lower_FDM(repaire d).stl
5.67 MiB 27 min <1 m 40 x 8 x 27 Download
0.11 MiB 2 min <1 m 3 x 4 x 9 Download
7_tongue_FDM(repaired).st l
2.89 MiB 10 min <1 m 8 x 11 x 24 Download
8_tsaheylu_L_FDM(repaired ).stl
5.95 MiB 1 h 25 min 1 m 17 x 128 x 25 Download
9_tsaheylu_R_FDM(repaired ).stl
5.55 MiB 1 h 24 min 1 m 43 x 100 x 51 Download
11.02 MiB 2 h 25 min 1 m 30 x 37 x 64 Download
30.34 MiB 17 h 55 min 10 m 142 x 68 x 114 Download
12_wing_R_1_FDM(repaired) .stl
12.29 MiB 5 h 4 min 3 m 18 x 115 x 65 Download
13_wing_R_2_FDM(repaired) .stl
10.29 MiB 7 h 35 min 5 m 28 x 95 x 107 Download
14_wing_R_3_FDM(repaired) .stl
10.82 MiB 3 h 42 min 2 m 29 x 77 x 124 Download
15_wing_R_4_FDM(repaired) .stl
9.26 MiB 1 h 6 min 1 m 16 x 47 x 40 Download
16_wing_R_5_FDM(repaired) .stl
11.40 MiB 1 h 51 min 1 m 13 x 37 x 100 Download
17_wing_R_6_FDM(repaired) .stl
10.44 MiB 2 h 2 min 1 m 11 x 44 x 137 Download
18_wing_R_7_FDM(repaired) .stl
10.17 MiB 1 h 55 min 1 m 18 x 42 x 99 Download
19_wing_R_8_FDM(repaired) .stl
11.16 MiB 2 h 28 min 1 m 14 x 41 x 124 Download
20_wing_R_9_FDM(repaired) .stl
10.35 MiB 2 h 1 m 11 x 49 x 84 Download
21_wing_R_10_FDM(repaired ).stl
11.16 MiB 2 h 23 min 1 m 17 x 48 x 141 Download
22_claw_R_1_FDM(repaired) .stl
2.78 MiB 23 min <1 m 22 x 5 x 24 Download
23_claw_R_2_FDM(repaired) .stl
0.93 MiB 14 min <1 m 5 x 11 x 21 Download
24_wing_L_1_FDM(repaired) .stl
12.51 MiB 5 h 51 min 3 m 27 x 117 x 63 Download
25_wing_L_2_FDM(repaired) .stl
9.52 MiB 7 h 10 min 5 m 19 x 105 x 107 Download
26_wing_L_3_FDM(repaired) .stl
8.58 MiB 2 h 53 min 2 m 22 x 71 x 118 Download
27_wing_L_4_FDM(repaired) .stl
9.07 MiB 1 h 8 min 1 m 12 x 43 x 38 Download
28_wing_L_5_FDM(repaired) .stl
9.60 MiB 2 h 1 min 1 m 21 x 38 x 116 Download
29_wing_L_6_FDM(repaired) .stl
10.75 MiB 2 h 14 min 1 m 26 x 40 x 138 Download
30_wing_L_7_FDM(repaired) .stl
10.15 MiB 2 h 10 min 1 m 10 x 40 x 118 Download
31_wing_L_8_FDM(repaired) .stl
10.71 MiB 2 h 1 min 1 m 14 x 42 x 120 Download
32_wing_L_9_FDM(repaired) .stl
11.13 MiB 1 h 57 min 1 m 13 x 42 x 94 Download
33_wing_L_10_FDM(repaired ).stl
9.83 MiB 2 h 3 min 1 m 14 x 42 x 127 Download
34_claw_L_1_FDM(repaired) .stl
2.26 MiB 19 min <1 m 19 x 6 x 22 Download
35_claw_L_2_FDM(repaired) .stl
1.21 MiB 14 min <1 m 5 x 13 x 22 Download
36_tail_1_FDM(repaired).s tl
7.58 MiB 1 h 8 min 1 m 43 x 32 x 72 Download
37_tail_2_FDM(repaired).s tl
15.13 MiB 5 h 55 min 4 m 129 x 29 x 77 Download
38_tail_3_FDM(repaired).s tl
10.10 MiB 2 h 10 min 1 m 13 x 77 x 81 Download
39_tail_4_FDM(repaired).s tl
11.03 MiB 2 h 43 min 1 m 30 x 82 x 76 Download
40_tail_5_FDM(repaired).s tl
7.82 MiB 1 h 30 min <1 m 14 x 27 x 117 Download
41_tail_6_FDM(repaired).s tl
8.77 MiB 1 h 30 min <1 m 17 x 18 x 120 Download
42_leg_L_FDM (repaired).s tl
6.82 MiB 39 min <1 m 29 x 23 x 26 Download
43_foot_L_FDM(repaired).s tl
11.14 MiB 1 h 52 min 1 m 28 x 44 x 55 Download
44_leg_R_FDM(repaired).st l
10.66 MiB 1 h 6 min 1 m 29 x 33 x 36 Download
45_foot_R_FDM(repaired).s tl
10.87 MiB 1 h 14 min 1 m 20 x 52 x 58 Download
46_platform_FDM(repaired) .stl
26.46 MiB 13 h 21 min 7 m 149 x 147 x 13 Download
47_ge_lock_7S(x4)_FDM(rep aired).stl
0.02 MiB 3 min <1 m 18 x 7 x 2 Download
Keychain (repaired).stl
0.35 MiB 23 min <1 m 30 x 30 x 2 Download
Tag (repaired).stl
1.70 MiB 1 h 16 min 1 m 150 x 18 x 5 Download
28.67 MiB 2 h 39 min 1 m 32 x 34 x 55 Download
4_jaw_top_FDM(repaired).s tl
3.41 MiB 16 min <1 m 12 x 24 x 10 Download
5_jaw_lower_FDM(repaired) .stl
3.84 MiB 14 min <1 m 12 x 25 x 9 Download


The great leonopteryx is the apex aerial predator of Pandora, the celebrated and feared ”flying king lion" who holds a central place in Na'vi culture. As Jake Sully once said, the beast can be the last shadow one would ever see if they happen to become the creature’s prey thanks to its preferred method of attack - from above. Fascinated by the unworldly appearance of Toruk, the author of the model spent 225 hours to depict minutely the deadly and respected predator. The figurine was created with Toruk’s distinctive razor-sharp crests on the opposite sides of its head and powerful jaws which are slightly opened in a warning. The Last Shadow’s wingspan is not fully revealed though the model’s pose does justice to the unusual membranous wings of the beast. Those three individual finned members on each side are even known to be rotating in the film for the Leonopteryx to induce or retard vortex formation! Each of the figurine’s six limbs has strong talons on the end, perfect for grasping prey. And those twin tails that prolong Toruk’s unusual body are known to be perfect for flight control and high performance. As it is commonly known, in the Na'vi culture, those individuals who manage to make tsaheylu with the Great Leonopteryx are given an honourable title Toruk Makto. The sixth representative of this highly respected title Jake Sully is also available on Gambody for your to complete an awesome 3D printed Avatar diorama!


Toruk is a static assembly figurine and its moderation and adaptation for different types of 3D printers took Gambody team 68 hours in total. The model’s cutting was chosen by our team to minimise the amount of filament needed for generated support and some of the parts were hollowed out for you to save resin in leonopteryx’ Eco version. The figurine was divided into as many assembly parts as needed to fit even the smallest 3D printers' build plates and for you to nevertheless receive a large winged beast after assembly. In order to receive the cleanest result possible the creature’s jaws were extracted and are now provided as separate parts, as well as the model's large front fang, talons on the end of each limb and strips and sharp crests on the head. All assembly parts are provided in STL files in recommended positions that were worked out so to ensure the smoothness of the details’ surfaces after printing and that the 3D printing beginners won't face difficulties when placing the parts on a build plate. All parts have special connecting elements for you to assemble the figurine in the easiest way possible and there are locks provided to connect some details if you don’t want to glue the parts.

The figurine is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from Toruk's actual wingspan that is 25146 mm. The 3D printing figurine's chosen scale is 1/32 for the FFF/FDM version and 1/64 for the DLP/SLA/SLS versions.


FFF/FDM 1.0 version features:
- Contains 47 parts;
- A printed model is 182 mm tall, 629 mm wide, 392 mm deep;
- Assembly kit includes lock 47_ge_lock_7S(x4) that needs to be printed 4 times to connect parts without glue;
- The version's scale is chosen for you to complete the diorama with Jake Sully figurine; 
- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:
- Contains 21 parts;
- A printed model is 91 mm tall, 315 mm wide, 196 mm deep;
- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

DLP/SLA Eco 1.0 version features:
- Contains 21 parts;
- A printed model is 91 mm tall, 315 mm wide, 196 mm deep;
- Contains some hollowed out parts to save resin.

SLS 1.0 version features:
- Made as solid one-piece figurine;
- A printed model is 91 mm tall, 315 mm wide, 196 mm deep;
- Contains 2 parts - a one-piece model with the platform separated.


- STL files of Toruk 3D printing figurine which consist of 91 parts;
- 4 versions of files for this model for FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS;
- High-poly detailed figurine of Toruk;
- Detailed settings that we provide as a recommendation for Cura , Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get Toruk 3D printing figurine​ immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Toruk 3D printing figurine at Gambody YouTube channel.

Also, you may like other Avatar 3D Printing Model as well as Jake Sully figurine to complete the diorama.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?


Below you can find printing recommendations for CuraSimplify3D and Slic3r software.

Cura printing recommendations:

These are basic settings that were tested in Cura 4.8.0 slicer. 

The test models were printed on Ultimaker 2, Creality Ender 3, Creality CR-10S Pro V2, Anycubic I3 Mega, Anycubic I3 MegaS 3D printers with PLA and PETG filaments.

Disclaimer: The following printing settings are a recommendation, not an obligation. The parameters can vary depending on the peculiarities of your 3D printer, the material you use and especially the particular assembly part at hand. Each part that any model comprises often needs preliminary review and you are free to tweak the settings the way you find suitable.

- You can scale up the model (downscaling is not recommended!);
- All connectors should be printed at 100% Infill;
- For all parts of locks (“ge_lock” in “Source files”) you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

Layer Height: 0.12 mm (you can also set Layer Height at 0.16 or 0.2mm for 0.4mm nozzles)
Initial Layer Height: 0.2 mm (carefully level the print bed and keep your Initial Layer Height the same as the main Layer Height)

Line Width: 0.4 mm
Wall Line Width: 0.4 mm
Outer Wall Line Width: 0.4 mm
Inner Wall(s) Line Width: 0.4 mm
Top/Bottom Line Width: 0.4 mm
Infill Line Width: 0.4 mm
Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm

Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
Wall Line Count: 2

Outer Wall Wipe Distance: 0.3 mm
Top Surface Skin Layers: 0

Top/Bottom Thickness: 0.6 mm
Top Thickness: 0.6 mm
Top Layers: 5
Bottom Thickness: 0.6 mm
Bottom Layers: 5
Initial Bottom Layers: 5

Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Optimize Wall Printing Order: Check

Compensate Wall Overlaps: Check
Compensate Inner Wall Overlaps: Check

Minimum Wall Flow: 0%
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Hole horizontal expansion: 0

Z Seam Alignment: User Specified
Z Seam Position: Back
Z Seam X: Average length of your printer’s plate (e.g.”150” if your plate is 300mm on the X-axis)
Z Seam Y: A value higher than the length of your plate on the Y-axis (e.g. 700)

Seam Corner Preference: Hide Seam
Extra Skin Wall Count: 1
Skin Overlap Percentage: 10%
Skin Overlap 0.04 mm

Infill Density: 20% (for all smaller parts and for all parts of connectors use 100% Infill)
Infill Pattern: Triangles
Connect Infill Lines: Check
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Line Multiplier: 1
Extra Infill Wall Count: 0

Infill Overlap Percentage: 10-20%
Infill Overlap: 0.04 mm

Skin Overlap Percentage: 5%
Skin Overlap: 0.02 mm

Infill Wipe Distance: 0 mm
Infill Layer Thickness: 0.24 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2

Skin Removal Width: 0.8 mm
Top Skin Removal Width: 0.8 mm
Bottom Skin Removal Width: 0.8 mm

Skin Expand Distance: 0.8
Top Skin Expand Distance: 0.8
Bottom Skin Expand Distance: 0.8

Maximum Skin Angle for Expansion: 90˚
Minimum Skin Width for Expansion: 0.0
Skin Edge Support Thickness: 0
Skin Edge Support Layers: 0

Initial Layer Flow: 100%
Printing Temperature: See your filament settings
Initial Printing Temperature: Your filament settings
Final Printing Temperature: Your filament settings
Build Plate Temperature: Your filament settings
Build Plate Temperature Initial Layer: Your filament settings + 5°
Flow: 100% (Important! If you face difficulty printing the model, you may need to adjust the Flow parameter. You may research the topic using the Internet or seek assistance at our Customer Support Team at


You can increase the printing Speed by 20% when you print simple objects. For small/thin parts you need to decrease the Speed by 25% - 50%.

Print Speed: 50 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 25 mm/s
          Outer Wall Speed:25 mm/s
          Inner Wall Speed: 50 mm/s

Top/Bottom Speed: 25mm/s
Support Speed: 25 mm/s 
          Support Infill Speed: 45 mm/s
          Support Interface Speed: 25 mm/s
                Support Roof Speed: 25 mm/s
                Support Floor Speed: 25 mm/s

Travel Speed: 80 mm/s
Initial Layer Speed: 80 mm/s
Initial Layer Print Speed: 20 mm/s
Initial Layer Travel Speed: 80 mm/s

Skirt/Brim Speed: 20 mm/s
Z  Hop Speed: 5 mm/s
Number of Slower Layers: 2
Enable Acceleration Control: Check

When printing simple objects, you need to set all Acceleration parameters at 500 mm/s. For small/thin parts you need to decrease the Acceleration by 50% - 70%.

Enable Retraction: Check
Retraction Distance: 4-8 mm, 1-3 mm for Direct Extruder (This is the most important retraction parameter. You can find your optimal value of Retraction Distance by printing any test object, e.g. bridges, towers etc.)

Retraction Speed: 25mm/s
Retraction Retract Speed: 25 mm/s
Retraction Prime Speed: 25 mm/s

Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 1.5 mm
Maximum Retraction Count: 100
Minimum Extrusion Distance Window: 6,5 - 10 mm
Limit Support Retractions: Check
Combing Mode: All
Max Comb Distance With No Retract: 30 mm
Retract Before Outer Wall: Check
Avoid Printed Parts When Travelling: Check
Avoid Supports When Travelling: Check
Travel Avoid Distance: 1 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm
Z Hop When Retracted: Check
Z Hop Height: 0,3 mm

Enable Print Cooling: Check
Fan Speed: 100%
Regular Fan Speed: 100%
Maximum Fan Speed: 100% 

Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.36 mm
Regular Fan Speed at Layer: 3 

Minimum Layer Time: 10 s
Minimum Speed: 10 mm/s

Generate Support: Check
Support Structure: Normal (you can try using Tree Support Structure if you have difficulty printing any particular assembly part)
Support Placement: Everywhere 
Support Overhang Angle: 60° (this parameter can range from 30° to 70° depending on the part at hand)
Support Pattern: Zig Zag
Support Wall Line Count: 1 (stronger support that might be more difficult to remove) 0 (less strong support but is easier to remove)

Support Density: 15%
Support Line Distance: 2.6667 mm
Initial layer support line distance: 2.667 mm

Support Z Distance: 0.12 mm
Support Top Distance: 0.12 mm
Support Bottom Distance: 0.12 mm

Support X/Y Distance: 0.8-1 mm
Support Distance Priority: Z overrides X/Y
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Stair Step Minimum Slope Angle: 10°
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.2 mm
Gradual Support Infill Steps: 0
Minimum Support Area: 2 mm

Enable Support Interface: Check (generates additional “pillow” on the support structure that leads to a more even surface, but can be difficult to remove in hard-to-reach areas)
Enable Support Roof: Check
Enable Support Floor: Check

Support Interface Thickness: 0.8 mm
Support Roof Thickness: 0.8 mm
Support Floor Thickness: 0.8 mm

Support Interface Resolution 0.2 mm
Support Interface Density: 50-100%
        Support Roof Density: 50-100%
Support Roof Line Distance: 0.8 mm
        Support Floor Density: 50-100%
Support Floor line Distance:  0.4mm

Support Interface Pattern: Grid 
Support Roof Pattern: Grid (this parameter should differ from Bottom Pattern Initial Layer in “Shell” section)
Support Floor Pattern: Grid

Minimum Support Interface Area: 10mm
Minimum Support Roof Area: 10 mm
Minimum Support Floor Area: 10 mm

Support Interface Horizontal Expansion: 0.0 mm
Support Roof Horizontal Expansion: 0.0 mm
Support Floor Horizontal Expansion: 0.0 mm

Fan Speed Override: Check
Supported Skin Fan Speed: 100%
Use Towers: Check
Tower Diameter: 4 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Skirt/Brim (For unsteady parts, and those parts that may come unstuck use “Brim”. For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
       Brim Line Count: 10
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Extruder 1 Temperature: 210
Heated Bed: 60

Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
  Detect thin walls: Check
  Detect bridging perimeters: Check
  Seam position: Random
  Fill desity: 20%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
  Infill/Perimeters overlap: 20%
  Bridge flow ratio: 0.95
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm


comments powered by Disqus

Similar items

Browse more newly listed 3D printings