Make pre-order

William Birkin Monster 3D Printing Miniature | Assembly

cm: 35.8 w x 21.3 d x 33.2 h
in: 14.094 w x 8.386 d x 13.071 h
BUY FOR  $19.99

Source Files




Printing Details

This 3D Miniature consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Version 1 and Version 2 are the files for William Birkin Monster 3D Miniature optimized for 3D printing, the preview pictures of which you see above.

It is recommended:

  • to print Version 1 STL files on FDM/FFF 3D printers;
  • to print Version 2 STL files on DLP/SLA/SLS 3D printers.
File Name File Size Time / Filament
1_Ge_lock_7S (x8).STL
0.02 MiB 3 min
<1 m
2_Ge_lock_7S_70_ (x2).STL
0.02 MiB 2 min
<1 m
20.15 MiB 42 h 35 min
28 m
3.42 MiB 8 h 35 min
6 m
1.46 MiB 7 h 43 min
5 m
2.21 MiB 8 h 26 min
4 m
2.46 MiB 12 h 59 min
8 m
6.52 MiB 10 h 40 min
6 m
5.82 MiB 13 h 28 min
8 m
2.22 MiB 11 h 8 min
7 m
2.23 MiB 8 h 57 min
5 m
21.72 MiB 44 h 54 min
26 m


William Birkin is a scientist, virologist, responsible for the project for the creation of the G-virus, which served as a catalyst for the tragedy that occurred in Raccoon City. Birkin began work at the research center of the corporation "Umbrella" under the leadership of the first general director James Marcus in 1977 when he was only sixteen. There he also met his future close friend and rival Albert Wesker. They both took part in the creation of the T-virus until the closure of the research center. He completed the G-virus study in September 1998. Birkin planned to use it as a ticket to the board of directors of the corporation "Umbrella". However, having begun to argue with his superiors, Birkin changed his plans and decided to leave the virus to himself to late sell it to the US government. He even demanded the intervention of the military in order to get him out of the laboratory. The detachment did not come after him, but the group "Alpha" of the security service "Umbrella" received orders from Spencer to reached the laboratory and seized the work of Birkin. During the skirmish, one of the soldiers could not stand the nerves and he wounded Birkin with a burst of the machine gun. Grabbing for the life Birkin introduced himself a G-virus and thanks to this he survived and immediately transformed into a terrible monster. After the transformation in G, Birkin went for a group of "Alpha" who was in the sewer. The shocked fighters tried to stop him but the weapon was useless against the "new" Birkin and the whole team remained in the sewerage of Raccoon City. During this massacre, Birkin crushed several tubes with a T-virus. Local rats who tried the virus on taste smashed it around the city, causing the tragedy that swept the Raccoon City.


The model is saved in STL files, a format supported by most 3D printers

FDM version features:
- Contain 12 parts;
- Made with Locks for better fixing. One part of Lock (1_Ge_lock_7S (x8)) you need to print 8 times. Second part of Lock (2_Ge_lock_7S_70_ (x2)) you need to print twice;
- Made with platform;
- All parts are divided in such way that you will print them with the smallest amount of supports.

SLS/SLA version features:
- Same as FDM but made as 1 part.

All STL files for 3D printing have been checked in Netfabb and no errors were shown.

Note: Before starting 3D printing the model, read the Printing Details for CURA 3.2.1. Software.

There are 12 parts for FFF/FDM version and 1 part for SLS/SLA version.

Scale: His tall in life is 2320 mm. Model made as 1/7 scale in FDM version and 1/14 in SLS/SLA version.

FDM version dimensions:
After being printed will stand - 332 mm tall, 358 mm wide, 213 mm deep;

SLS/SLA version dimensions:
After being printed will stand - 166 mm tall, 179 mm wide, 107 mm deep;
- Has only 1 detail, to keep printing costs down.


- STL files of William Birkin Monster 3D Miniature for 3D printing which consist of 13 parts;
- 2 versions of files for this model for FFF/FDM and SLS/SLA;
- Made with platform;
- Model fixed by the Locks;
- High-poly detailed miniature of William Birkin Monster;
- Detailed settings that we provide for Cura 3.2.1. for the best print;
- Full technical support from the Gambody Support Team.

Watch the tutorial video on how to assemble William Birkin Monster 3D Printing Miniature at Gambody YouTube channel.

You can get Model of William Birkin Monster for 3D Printing right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Also, you may like other villains 3D Printing Miniatures.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.2.1 and printed on an Ultimaker 2 in PLA material.

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

To avoid printing problems, we recommend the following settings:

Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Print Speed: 45 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
Travel Speed: 120 mm/s
Initial Layer Speed: 30 mm/s
  Initial Layer Print Speed: 30 mm/s
  Initial Layer Travel Speed: 60 mm/s
Skirt/Brim Speed: 30 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 1.3333 mm
Support Z Distance: 0.3 mm
    Support Top Distance: 0.3 mm
    Support Bottom Distance: 0.3 mm
Support X/Y Distance: 0.7 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.2 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 18 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.


comments powered by Disqus
Other author's 3D printings


William Birkin, Monster, Villains, Boss, Assembly, Resident Evil, friday13, japan, gelloween, halloween shop, game, xmas18

Similar items

Browse more newly listed 3D printings