Make pre-order

cm: 17.096 w x 17.51 d x 16.036 h
in: 6.731 w x 6.894 d x 6.313 h
BUY FOR  $19.99

Source Files




Printing Details

This 3D model consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.

Download parts kit 2_2 and kit 2_14 for free to check the printability and test the quality before buying all STL files of the 3D model.

Download Free Samples

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

File Name File Size Time / Filament
kit 1_1 (repaired).stl
2.33 MiB 4 h 55 min
3 m
kit 1_2 (repaired).stl
8.59 MiB 6 h 32 min
3 m
kit 1_3 (repaired).stl
24.76 MiB 126 h 37 min
88 m
kit 1_4 (repaired).stl
47.21 MiB 18 h 20 min
12 m
kit 1_5 (repaired).stl
21.36 MiB 10 h 15 min
7 m
kit 2_1 (repaired).stl
41.20 MiB 14 h 3 min
9 m
kit 2_2 (repaired).stl
11.37 MiB 17 h 31 min
12 m
kit 2_3 (repaired).stl
3.50 MiB 6 h 44 min
4 m
kit 2_4 (repaired).stl
8.15 MiB 3 h 28 min
2 m
kit 2_5 (repaired).stl
5.01 MiB 7 h 3 min
4 m
kit 2_6 (repaired).stl
11.89 MiB 9 h 3 min
5 m
kit 2_7 (repaired).stl
11.92 MiB 8 h 33 min
5 m
kit 2_8 (repaired).stl
0.50 MiB 1 h 48 min
1 m
kit 2_9 (repaired).stl
0.50 MiB 1 h 48 min
1 m
kit 2_10 (repaired).stl
24.89 MiB 24 h 47 min
13 m
kit 2_12 (repaired).stl
21.35 MiB 10 h 13 min
7 m
kit 2_11 (repaired).stl
3.37 MiB 7 h 14 min
4 m
kit 2_13 (repaired).stl
4.77 MiB 6 h 42 min
4 m
kit 2_14 (repaired).stl
42.27 MiB 10 h 32 min
7 m
kit 2_10_NW (repaired).st l
11.39 MiB 22 h 51 min
12 m

Dreadnought 3D model is inspired by the war towering machines resembling huge heavy armor suits. Equipped with incredible firepower, the Dreadnoughts leave nothing but ash behind them.

The towering power armor is controlled by a pilot that is connected to the suit’s cybernetic system. Due to this fact, the pilot is able to use the suit as if it is its own body.

The Dreadnought 3D model showcases all the might and fear that the prototype embodies. Created in Autodesk Maya, the figurine is a high-poly model showing intricate details of the outer shell. For printing optimization, the STL files of the 3D model are made solid, facilitating their handling in any slicing program.

Also, the STL files are checked and corrected for errors in Netfabb. They are tested in CURA 2.3.1. slicing program. It is highly advised to print the files at 0.1 mm layer height for accurate printing results. For other 3D printing recommendations, please see Printing Details tab above.

You can opt for one of the 2 variants of Dreadnought 3D model: static, consisting of 5 parts (kit 1) and assembly, consisting of 14 parts (kit 2). Support is used for their 3D printing.

The parts don’t require glue for the assembly.

Buy Dreadnought 3D model by clicking the green Buy button in the top-right corner of the page. Add the files to your shopping card. Continue to checkout. Pay securely with PayPal or your credit card. Download the files in a .zip folder together with a PDF file with the printing recommendations.

If you don’t have a 3D printer of your own, you can use the services of our partners, 3DHubs and Treatstock. Just select the files you want to 3D print and click the Print with 3DHubs or Print with Treatstock button.

This model was tested in Cura 2.3.1. To avoid printing problems, we recommend the following settings:


Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
Wall Line Width: 0.4 mm
Outer Wall Line Width: 0.4 mm
Inner Wall(s) Line Width: 0.4 mm
Top/Bottom Line Width: 0.4 mm
Infill Line Width: 0.4 mm
Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm


Wall Thickness: 0.8 mm
Wall Line Count: 2
Top/Bottom Thickness: 0.8 mm
Top Thickness: 0.8 mm
Top Layers: 8
Bottom Thickness: 0.8 mm
Bottom Layers: 8
Top/Bottom Pattern: Lines
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
Compensate Outer Wall Overlaps: Check
Compensate Inner Wall Overlaps: Check
Horizontal Expansion: 0 mm
Z Seam Alignment: Shortest


Infill Density: 25%
Infill Line Distance: 3.2 mm
Infill Pattern: Grid
Infill Overlap Percentage: 10%
Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 0
Infill Before Walls: Check


Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Standby Temperature: 175°C
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
Nozzle Switch Retract Speed: 20 mm/s
Nozzle Switch Prime Speed: 20 mm/s


Print Speed: 60 mm/s
Infill Speed: 80 mm/s
Wall Speed: 30 mm/s
Outer Wall Speed: 30 mm/s
Inner Wall Speed: 60 mm/s
Top/Bottom Speed 15 mm/s
Support Speed: 60 mm/s
Support Infill Speed: 60 mm/s
Travel Speed: 120 mm/s
Initial Layer Speed: 15 mm/s
Initial Layer Print Speed: 15 mm/s
Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed 15 mm/s
Maximum Z Speed: 0 mm/s


Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm


Enable Print Cooling: Check
Fan Speed: 100%
Regular Fan Speed: 100%
Maximum Fan Speed: 100%
Regular/Maximum Fan Speed Threshold: 10 s
Regular Fan Speed at Height: 0.3 mm
Regular Fan Speed at Layer: 2
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s


Enable Support: Check
Support Placement: Everywhere
Support Overhang Angle: 50°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 30 %
Support Line Distance: 1.3333 mm
Support Z Distance: 0.1 mm
Support Top Distance: 0.1 mm
Support Bottom Distance: 0.1 mm
Support X/Y Distance: 0.7 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.2 mm
Support Stair Step Height: 0.3 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65°

Build Plate Adhesion

Build Plate Adhesion Type: Brim
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
Brim Line Count: 20
Brim Only on Outside: Check

Mesh Fixes

Union Overlapping Volumes: Check

Special Modes

Print Sequence: All at Once
Surface Mode: Normal


Extra Skin Wall Count: 0

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.


comments powered by Disqus
Other author's 3D printings


Warhammer, Dreadnought, Robot, Game model, Static

Similar items

Browse more newly listed 3D printings