Make pre-order

Alien Xenomorph in Diorama for 3D printing | Assembly

(5)
average
cm: 22.9 w x 20.9 d x 32.6 h
in: 9.016 w x 8.228 d x 12.835 h
31
BUY FOR  $24.99

Source Files

|

Description

|

Printing Details

This 3D Figurine consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Alien Xenomorph in Diorama for 3D printing comes in 4 versions for each 3D printer type (FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS). Files for each version are available for download after the purchase.

Detailed information about this 3D printing figurine is available in the DESCRIPTION section.

File Name File Size Time / Filament
1_head_FDM(repaired).stl
21.53 MiB 6 h 56 min
4 m
Download
2_body_FDM(repaired).stl
23.93 MiB 28 h 37 min
20 m
Download
3_spike_1_FDM(repaired).s tl
3.98 MiB 31 min
<1 m
Download
4_spike_2_FDM(repaired).s tl
7.86 MiB 58 min
<1 m
Download
5_spike_3_FDM(repaired).s tl
7.36 MiB 56 min
<1 m
Download
6_spike_4_FDM(repaired).s tl
5.90 MiB 49 min
<1 m
Download
7_spike_5_FDM(repaired).s tl
6.18 MiB 50 min
<1 m
Download
8_arm_L_1_FDM(repaired).s tl
13.89 MiB 1 h 35 min
1 m
Download
9_arm_L_2_FDM(repaired).s tl
8.29 MiB 56 min
<1 m
Download
10_hand_L_FDM(repaired).s tl
10.07 MiB 1 h 16 min
1 m
Download
11_arm_R_1_FDM(repaired). stl
12.01 MiB 1 h 26 min
1 m
Download
12_arm_R_2_FDM(repaired). stl
8.84 MiB 1 h 26 min
1 m
Download
13_hand_R_FDM(repaired).s tl
11.58 MiB 1 h 17 min
1 m
Download
14_leg_L_FDM(repaired).st l
12.97 MiB 6 h 9 min
4 m
Download
15_foot_L_FDM(repaired).s tl
9.40 MiB 3 h 37 min
2 m
Download
16_leg_R_FDM(repaired).st l
10.61 MiB 5 h 58 min
4 m
Download
17_foot_R_FDM(repaired).s tl
10.18 MiB 4 h 42 min
3 m
Download
18_tail_1_FDM(repaired).s tl
13.27 MiB 6 h 47 min
4 m
Download
19_tail_2_FDM(repaired).s tl
10.74 MiB 5 h 55 min
4 m
Download
20_tail_3_FDM(repaired).s tl
11.98 MiB 3 h 34 min
2 m
Download
21_tail_4_FDM(repaired).s tl
9.62 MiB 4 h 51 min
3 m
Download
22_tail_5_FDM(repaired).s tl
6.76 MiB 42 min
<1 m
Download
23_box_FDM(repaired).stl
15.49 MiB 30 h 20 min
17 m
Download
24_egg_1_FDM(repaired).st l
9.61 MiB 6 h 4 min
3 m
Download
25_egg_2_FDM(repaired).st l
7.93 MiB 3 h 32 min
2 m
Download
26_egg_3_FDM(repaired).st l
8.55 MiB 4 h 23 min
2 m
Download
27_egg_4_FDM(repaired).st l
8.48 MiB 3 h 17 min
2 m
Download
28_egg_5_FDM(repaired).st l
7.34 MiB 2 h 29 min
1 m
Download
29_egg_6_FDM(repaired).st l
8.25 MiB 3 h 51 min
2 m
Download
30_egg_7_FDM(repaired).st l
7.47 MiB 2 h 31 min
1 m
Download
31_platform_1_FDM (repair ed).stl
10.74 MiB 7 h 56 min
4 m
Download
32_platform_2_FDM (repair ed).stl
8.65 MiB 7 h 47 min
4 m
Download
33_platform_3_FDM (repair ed).stl
9.72 MiB 7 h 9 min
4 m
Download
34_platform_4_FDM (repair ed).stl
8.58 MiB 7 h 2 min
4 m
Download
35_ge_lock_7S(x14)_FDM(re paired).stl
0.02 MiB 3 min
<1 m
Download
Keychain (repaired).stl
0.35 MiB 23 min
<1 m
Download
Tag (repaired).stl
1.70 MiB 1 h 16 min
1 m
Download

ABOUT THIS 3D FIGURINE

Xenomorph is a menacing extraterrestrial species, one of the deadliest of all known aliens that was first seen in 1979 as a terrible antagonist in sci-fi horror classic Alien. They say that the impact of this horror film series is inestimable - the whole genre that now features a bewildering variety of deadly extraterrestrial creatures is considered to have been launched once the alien classic was first released on the big screen. Xenomorph is said to be the perfect killing machine. Small wonder, given its impenetrable exoskeleton and ability both to learn quickly and to inherit physical characteristics from its host. A characteristic feature of alien’s hunting tactics is waiting for the pray stealthily and this is perfectly conveyed in the pose the author of the Xenomorph 3D printing diorama chose to depict the monster in. It is crouched menacingly on the top of a slightly elevated construction where the alien can presumably watch the prey from but still remain unnoticed. And though the origin and back-story of Xenomorph were only theorised by the fans with every new instalment in the franchise, at least we do know where to expect the monster to appear from. The Xenomorph 3D printing diorama features the set of eggs, also known as Ovomorphs which are basically capsules containing Facehuggers - the second stage of Xenomorph’s life cycle that launches itself onto the host's face and impregnates it to grow into an adult alien. Sounds creepy, doesn’t it? Good thing that these eggs are only hatched in their 3D printing form - that was the way the 3D artist depicted the creatures, having spent on the creative project 132 hours in total. “In space, no one can hear you scream” - but should you print your own Xenomorph with Hatched Eggs diorama you will have at least several aliens to fight on your side.

ADAPTATION FOR 3D PRINTING

Alien Xenomorph in diorama for 3D printing is a static assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 28 hours in total. For you to receive the cleanest result possible the diorama was divided into many assembly parts and each hatched egg also comes separately to be further attached to the diorama’s platform as an independent assembly piece. The cutting of the Alien Xenomorph figurine itself was chosen by our team to minimise the amount of filament needed for generated support and some of the diorama’s parts were hollowed out for you to save resin. Moreover, in order to conceal the places where the assembly parts of the model must be connected, the figurine was cut along the anatomic folds of the alien’s exoskeleton. All the assembly parts are provided in STL files in recommended positions that were worked out so to ensure the smoothness of the details’ surfaces after printing and that the 3D printing beginners won't face difficulties when placing the parts on a build plate. 

The figurine is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from Xenomorph's actual height that is 2225 mm. The 3D printing figurine's chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS versions.

VERSIONS' SPECIFICATIONS

FFF/FDM 1.0 version features:
- Contains 35 parts;
- A printed model is 326 mm tall, 229 mm wide, 209 mm deep;
- Assembly kit includes locks to connect the parts without glue. One lock 35_ge_lock_7S(x14) needs to be printed 14 times;
- Made with a platform with a set of hatched eggs;
- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:
- Contains 10 parts;
- A printed model is 163 mm tall, 115 mm wide, 105 mm deep;
- Made with a platform with a set of hatched eggs;
- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

DLP/SLA Eco 1.0 version features:
- Contains 10 parts;
- A printed model is 163 mm tall, 115 mm wide, 105 mm deep;
- Made with a platform with a set of hatched eggs;
- Contains some hollowed out parts to save resin.

SLS 1.0 version features:
- Made as solid one-piece figurine;
- A printed model is 163 mm tall, 115 mm wide, 105 mm deep;
- Contains 3 parts - a one-piece model and the figurine with the platform separated.

WHAT WILL YOU GET AFTER PURCHASE?

- STL files of Alien Xenomorph 3D printing diorama which consist of 58 parts;
- 4 versions of files for this model for FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS;
- High-poly detailed figurine of Alien Xenomorph;
- Detailed settings that we provide as a recommendation for Cura 3.5.1, Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get Alien Xenomorph in Diorama for 3D printing​ immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Alien Xenomorph 3D printing diorama at Gambody YouTube channel.

Also, you may like other Alien Figurines for 3D Printing, as well as 3D Printing Figurines of Predator.

_______
FAQ: 

Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.5.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for CuraSimplify3D and Slic3r softwares.

Cura printing recommendations:

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

To avoid printing problems, we recommend the following settings:

Quality
Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Shell 
Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill 
Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Material 
Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Speed 
Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s 
     Support Infill Speed: 45 mm/s
Travel Speed: 45 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 45 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Travel 
Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.6562 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Cooling 
Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Support 
Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 2.2 mm
Support Z Distance: 0.13 mm
    Support Top Distance: 0.13 mm
    Support Bottom Distance: 0.13 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 15 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Experimental
Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Extruder
Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Layer
Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Additions
Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Infill
Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Support
Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Temperature
Extruder 1 Temperature: 210
Heated Bed: 60

Cooling
Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Speeds
Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Other
Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
Quality
  Detect thin walls: Check
  Detect bridging perimeters: Check
Advanced
  Seam position: Random
Infill
  Fill desity: 20%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
Advanced
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
Skirt
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
Brim 
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
Raft
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
Modifiers
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
Autospeed
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
Overlap
  Infill/Perimeters overlap: 20%
Flow
  Bridge flow ratio: 0.95
Other
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm

Comments

comments powered by Disqus
Other author's 3D printings

Tags

alien, xenomorph, yautja, assembly, predator, friday13

Similar items

Browse more newly listed 3D printings