Premium Stock

Alien Xenomorph in Diorama for 3D printing | Assembly

cm: 22.9 w x 20.9 d x 32.6 h
in: 9.016 w x 8.228 d x 12.835 h

Source Files




Printing Details

This 3D Figurine consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Alien Xenomorph in Diorama for 3D printing comes in 5 versions for each 3D printer type (FFF/FDM, DLP/SLA and SLS). Files for each version are available for download after the purchase.

Detailed information about this 3D printing figurine is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
23.93 MiB 28 h 37 min 20 m 78 x 71 x 130 Download
3_spike_1_FDM(repaired).s tl
3.98 MiB 31 min <1 m 12 x 16 x 46 Download
4_spike_2_FDM(repaired).s tl
7.86 MiB 58 min <1 m 11 x 24 x 73 Download
5_spike_3_FDM(repaired).s tl
7.36 MiB 56 min <1 m 15 x 19 x 73 Download
6_spike_4_FDM(repaired).s tl
5.90 MiB 49 min <1 m 22 x 19 x 58 Download
7_spike_5_FDM(repaired).s tl
6.18 MiB 50 min <1 m 11 x 24 x 60 Download
8_arm_L_1_FDM(repaired).s tl
13.89 MiB 1 h 35 min 1 m 34 x 38 x 49 Download
9_arm_L_2_FDM(repaired).s tl
8.29 MiB 56 min <1 m 14 x 14 x 56 Download
10_hand_L_FDM(repaired).s tl
10.07 MiB 1 h 16 min 1 m 24 x 32 x 61 Download
11_arm_R_1_FDM(repaired). stl
12.01 MiB 1 h 26 min 1 m 23 x 46 x 48 Download
12_arm_R_2_FDM(repaired). stl
8.84 MiB 1 h 26 min 1 m 14 x 49 x 46 Download
13_hand_R_FDM(repaired).s tl
11.58 MiB 1 h 17 min 1 m 23 x 30 x 52 Download
14_leg_L_FDM(repaired).st l
12.97 MiB 6 h 9 min 4 m 44 x 89 x 59 Download
15_foot_L_FDM(repaired).s tl
9.40 MiB 3 h 37 min 2 m 31 x 91 x 73 Download
16_leg_R_FDM(repaired).st l
10.61 MiB 5 h 58 min 4 m 99 x 39 x 52 Download
17_foot_R_FDM(repaired).s tl
10.18 MiB 4 h 42 min 3 m 47 x 54 x 82 Download
18_tail_1_FDM(repaired).s tl
13.27 MiB 6 h 47 min 4 m 34 x 48 x 93 Download
19_tail_2_FDM(repaired).s tl
10.74 MiB 5 h 55 min 4 m 46 x 48 x 71 Download
20_tail_3_FDM(repaired).s tl
11.98 MiB 3 h 34 min 2 m 33 x 46 x 67 Download
21_tail_4_FDM(repaired).s tl
9.62 MiB 4 h 51 min 3 m 38 x 75 x 75 Download
22_tail_5_FDM(repaired).s tl
6.76 MiB 42 min <1 m 16 x 34 x 58 Download
15.49 MiB 30 h 20 min 17 m 88 x 68 x 99 Download
24_egg_1_FDM(repaired).st l
9.61 MiB 6 h 4 min 3 m 48 x 49 x 60 Download
25_egg_2_FDM(repaired).st l
7.93 MiB 3 h 32 min 2 m 39 x 38 x 46 Download
26_egg_3_FDM(repaired).st l
8.55 MiB 4 h 23 min 2 m 42 x 39 x 54 Download
27_egg_4_FDM(repaired).st l
8.48 MiB 3 h 17 min 2 m 43 x 39 x 42 Download
28_egg_5_FDM(repaired).st l
7.34 MiB 2 h 29 min 1 m 37 x 38 x 33 Download
29_egg_6_FDM(repaired).st l
8.25 MiB 3 h 51 min 2 m 41 x 37 x 50 Download
30_egg_7_FDM(repaired).st l
7.47 MiB 2 h 31 min 1 m 34 x 37 x 35 Download
31_platform_1_FDM (repair ed).stl
10.74 MiB 7 h 56 min 4 m 90 x 90 x 19 Download
32_platform_2_FDM (repair ed).stl
8.65 MiB 7 h 47 min 4 m 90 x 90 x 21 Download
33_platform_3_FDM (repair ed).stl
9.72 MiB 7 h 9 min 4 m 90 x 90 x 20 Download
34_platform_4_FDM (repair ed).stl
8.58 MiB 7 h 2 min 4 m 90 x 90 x 20 Download
35_ge_lock_7S(x14)_FDM(re paired).stl
0.02 MiB 3 min <1 m 18 x 7 x 2 Download
Keychain (repaired).stl
0.35 MiB 23 min <1 m 30 x 30 x 2 Download
Tag (repaired).stl
1.70 MiB 1 h 16 min 1 m 150 x 18 x 5 Download
21.52 MiB 9 h 42 min 7 m 30 x 90 x 93 Download


Xenomorph is a menacing extraterrestrial species, one of the deadliest of all known aliens that was first seen in 1979 as a terrible antagonist in sci-fi horror classic Alien. They say that the impact of this horror film series is inestimable - the whole genre that now features a bewildering variety of deadly extraterrestrial creatures is considered to have been launched once the alien classic was first released on the big screen. Xenomorph is said to be the perfect killing machine. Small wonder, given its impenetrable exoskeleton and ability both to learn quickly and to inherit physical characteristics from its host. A characteristic feature of alien’s hunting tactics is waiting for the pray stealthily and this is perfectly conveyed in the pose the author of the Xenomorph 3D printing diorama chose to depict the monster in. It is crouched menacingly on the top of a slightly elevated construction where the alien can presumably watch the prey from but still remain unnoticed. And though the origin and back-story of Xenomorph were only theorised by the fans with every new instalment in the franchise, at least we do know where to expect the monster to appear from. The Xenomorph 3D printing diorama features the set of eggs, also known as Ovomorphs which are basically capsules containing Facehuggers - the second stage of Xenomorph’s life cycle that launches itself onto the host's face and impregnates it to grow into an adult alien. Sounds creepy, doesn’t it? Good thing that these eggs are only hatched in their 3D printing form - that was the way the 3D artist depicted the creatures, having spent on the creative project 132 hours in total. “In space, no one can hear you scream” - but should you print your own Xenomorph with Hatched Eggs diorama you will have at least several aliens to fight on your side.


Alien Xenomorph in diorama for 3D printing is a static assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 28 hours in total. For you to receive the cleanest result possible the diorama was divided into many assembly parts and each hatched egg also comes separately to be further attached to the diorama’s platform as an independent assembly piece. The cutting of the Alien Xenomorph figurine itself was chosen by our team to minimise the amount of filament needed for generated support and some of the diorama’s parts were hollowed out for you to save resin. Moreover, in order to conceal the places where the assembly parts of the model must be connected, the figurine was cut along the anatomic folds of the alien’s exoskeleton. All the assembly parts are provided in STL files in recommended positions that were worked out so to ensure the smoothness of the details’ surfaces after printing and that the 3D printing beginners won't face difficulties when placing the parts on a build plate. 

The figurine is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from Xenomorph's actual height that is 2225 mm. The 3D printing figurine's chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS versions.


FFF/FDM 1.0 version features:
- Contains 35 parts;
- A printed model is 326 mm tall, 229 mm wide, 209 mm deep;
- Assembly kit includes locks to connect the parts without glue. One lock 35_ge_lock_7S(x14) needs to be printed 14 times;
- Made with a platform with a set of hatched eggs;
- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:
- Contains 10 parts;
- A printed model is 163 mm tall, 115 mm wide, 105 mm deep;
- Made with a platform with a set of hatched eggs;
- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

DLP/SLA Eco 1.0 version features:
- Contains 10 parts;
- A printed model is 163 mm tall, 115 mm wide, 105 mm deep;
- Made with a platform with a set of hatched eggs;
- Contains some hollowed out parts to save resin.

DLP/SLA Pre-supported 1.0 version features:
- Contains 10 parts;
- A printed model is 163 mm tall, 115 mm wide, 105 mm deep;
- The STL files that this version comprises are pre-supportedhollowed out, and have drain holes where needed;
- You may choose to print the STL files one by one or several at once, depending on the dimensions of your resin 3D printer's build plate;
- When slicing several STL files at once, the attachment layers (Platform Touch Shape) may overlap, but the supports must not come into contact.

SLS 1.0 version features:
- Made as solid one-piece figurine;
- A printed model is 163 mm tall, 115 mm wide, 105 mm deep;
- Contains 3 parts - a one-piece model and the figurine with the platform separated.


- STL files of Alien Xenomorph 3D printing diorama which consist of 58 parts;
- 4 versions of files for this model for FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS;
- High-poly detailed figurine of Alien Xenomorph;
- Detailed settings that we provide as a recommendation for Cura , Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get Alien Xenomorph in Diorama for 3D printing​ immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Alien Xenomorph 3D printing diorama at Gambody YouTube channel.

Also, you may like other Alien vs Predator 3D Printing Models.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?


Below you can find printing recommendations for CuraSimplify3D and Slic3r software.

Cura printing recommendations:

These are basic settings that were tested in Cura 4.8.0 slicer. 

The test models were printed on Ultimaker 2, Creality Ender 3, Creality CR-10S Pro V2, Anycubic I3 Mega, Anycubic I3 MegaS 3D printers with PLA and PETG filaments.

Disclaimer: The following printing settings are a recommendation, not an obligation. The parameters can vary depending on the peculiarities of your 3D printer, the material you use and especially the particular assembly part at hand. Each part that any model comprises often needs preliminary review and you are free to tweak the settings the way you find suitable.

- You can scale up the model (downscaling is not recommended!);
- All connectors should be printed at 100% Infill;
- For all parts of locks (“ge_lock” in “Source files”) you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

Layer Height: 0.12 mm (you can also set Layer Height at 0.16 or 0.2mm for 0.4mm nozzles)
Initial Layer Height: 0.2 mm (carefully level the print bed and keep your Initial Layer Height the same as the main Layer Height)

Line Width: 0.4 mm
Wall Line Width: 0.4 mm
Outer Wall Line Width: 0.4 mm
Inner Wall(s) Line Width: 0.4 mm
Top/Bottom Line Width: 0.4 mm
Infill Line Width: 0.4 mm
Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm

Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
Wall Line Count: 2

Outer Wall Wipe Distance: 0.3 mm
Top Surface Skin Layers: 0

Top/Bottom Thickness: 0.6 mm
Top Thickness: 0.6 mm
Top Layers: 5
Bottom Thickness: 0.6 mm
Bottom Layers: 5
Initial Bottom Layers: 5

Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Optimize Wall Printing Order: Check

Compensate Wall Overlaps: Check
Compensate Inner Wall Overlaps: Check

Minimum Wall Flow: 0%
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Hole horizontal expansion: 0

Z Seam Alignment: User Specified
Z Seam Position: Back
Z Seam X: Average length of your printer’s plate (e.g.”150” if your plate is 300mm on the X-axis)
Z Seam Y: A value higher than the length of your plate on the Y-axis (e.g. 700)

Seam Corner Preference: Hide Seam
Extra Skin Wall Count: 1
Skin Overlap Percentage: 10%
Skin Overlap 0.04 mm

Infill Density: 20% (for all smaller parts and for all parts of connectors use 100% Infill)
Infill Pattern: Triangles
Connect Infill Lines: Check
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Line Multiplier: 1
Extra Infill Wall Count: 0

Infill Overlap Percentage: 10-20%
Infill Overlap: 0.04 mm

Skin Overlap Percentage: 5%
Skin Overlap: 0.02 mm

Infill Wipe Distance: 0 mm
Infill Layer Thickness: 0.24 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2

Skin Removal Width: 0.8 mm
Top Skin Removal Width: 0.8 mm
Bottom Skin Removal Width: 0.8 mm

Skin Expand Distance: 0.8
Top Skin Expand Distance: 0.8
Bottom Skin Expand Distance: 0.8

Maximum Skin Angle for Expansion: 90˚
Minimum Skin Width for Expansion: 0.0
Skin Edge Support Thickness: 0
Skin Edge Support Layers: 0

Initial Layer Flow: 100%
Printing Temperature: See your filament settings
Initial Printing Temperature: Your filament settings
Final Printing Temperature: Your filament settings
Build Plate Temperature: Your filament settings
Build Plate Temperature Initial Layer: Your filament settings + 5°
Flow: 100% (Important! If you face difficulty printing the model, you may need to adjust the Flow parameter. You may research the topic using the Internet or seek assistance at our Customer Support Team at


You can increase the printing Speed by 20% when you print simple objects. For small/thin parts you need to decrease the Speed by 25% - 50%.

Print Speed: 50 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 25 mm/s
          Outer Wall Speed:25 mm/s
          Inner Wall Speed: 50 mm/s

Top/Bottom Speed: 25mm/s
Support Speed: 25 mm/s 
          Support Infill Speed: 45 mm/s
          Support Interface Speed: 25 mm/s
                Support Roof Speed: 25 mm/s
                Support Floor Speed: 25 mm/s

Travel Speed: 80 mm/s
Initial Layer Speed: 80 mm/s
Initial Layer Print Speed: 20 mm/s
Initial Layer Travel Speed: 80 mm/s

Skirt/Brim Speed: 20 mm/s
Z  Hop Speed: 5 mm/s
Number of Slower Layers: 2
Enable Acceleration Control: Check

When printing simple objects, you need to set all Acceleration parameters at 500 mm/s. For small/thin parts you need to decrease the Acceleration by 50% - 70%.

Enable Retraction: Check
Retraction Distance: 4-8 mm, 1-3 mm for Direct Extruder (This is the most important retraction parameter. You can find your optimal value of Retraction Distance by printing any test object, e.g. bridges, towers etc.)

Retraction Speed: 25mm/s
Retraction Retract Speed: 25 mm/s
Retraction Prime Speed: 25 mm/s

Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 1.5 mm
Maximum Retraction Count: 100
Minimum Extrusion Distance Window: 6,5 - 10 mm
Limit Support Retractions: Check
Combing Mode: All
Max Comb Distance With No Retract: 30 mm
Retract Before Outer Wall: Check
Avoid Printed Parts When Travelling: Check
Avoid Supports When Travelling: Check
Travel Avoid Distance: 1 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm
Z Hop When Retracted: Check
Z Hop Height: 0,3 mm

Enable Print Cooling: Check
Fan Speed: 100%
Regular Fan Speed: 100%
Maximum Fan Speed: 100% 

Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.36 mm
Regular Fan Speed at Layer: 3 

Minimum Layer Time: 10 s
Minimum Speed: 10 mm/s

Generate Support: Check
Support Structure: Normal (you can try using Tree Support Structure if you have difficulty printing any particular assembly part)
Support Placement: Everywhere 
Support Overhang Angle: 60° (this parameter can range from 30° to 70° depending on the part at hand)
Support Pattern: Zig Zag
Support Wall Line Count: 1 (stronger support that might be more difficult to remove) 0 (less strong support but is easier to remove)

Support Density: 15%
Support Line Distance: 2.6667 mm
Initial layer support line distance: 2.667 mm

Support Z Distance: 0.12 mm
Support Top Distance: 0.12 mm
Support Bottom Distance: 0.12 mm

Support X/Y Distance: 0.8-1 mm
Support Distance Priority: Z overrides X/Y
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Stair Step Minimum Slope Angle: 10°
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.2 mm
Gradual Support Infill Steps: 0
Minimum Support Area: 2 mm

Enable Support Interface: Check (generates additional “pillow” on the support structure that leads to a more even surface, but can be difficult to remove in hard-to-reach areas)
Enable Support Roof: Check
Enable Support Floor: Check

Support Interface Thickness: 0.8 mm
Support Roof Thickness: 0.8 mm
Support Floor Thickness: 0.8 mm

Support Interface Resolution 0.2 mm
Support Interface Density: 50-100%
        Support Roof Density: 50-100%
Support Roof Line Distance: 0.8 mm
        Support Floor Density: 50-100%
Support Floor line Distance:  0.4mm

Support Interface Pattern: Grid 
Support Roof Pattern: Grid (this parameter should differ from Bottom Pattern Initial Layer in “Shell” section)
Support Floor Pattern: Grid

Minimum Support Interface Area: 10mm
Minimum Support Roof Area: 10 mm
Minimum Support Floor Area: 10 mm

Support Interface Horizontal Expansion: 0.0 mm
Support Roof Horizontal Expansion: 0.0 mm
Support Floor Horizontal Expansion: 0.0 mm

Fan Speed Override: Check
Supported Skin Fan Speed: 100%
Use Towers: Check
Tower Diameter: 4 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Skirt/Brim (For unsteady parts, and those parts that may come unstuck use “Brim”. For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
       Brim Line Count: 10
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Extruder 1 Temperature: 210
Heated Bed: 60

Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
  Detect thin walls: Check
  Detect bridging perimeters: Check
  Seam position: Random
  Fill desity: 20%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
  Infill/Perimeters overlap: 20%
  Bridge flow ratio: 0.95
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm


comments powered by Disqus

Similar items

Browse more newly listed 3D printings