Make pre-order

(2)
average
cm: 47 w x 18.5 d x 30.7 h
in: 18.504 w x 7.283 d x 12.087 h
4
BUY FOR  $16.99

Source Files

|

Description

|

Printing Details

This 3D model consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Version 1 and Version 2 are the files for Armored Hulk 3D Model optimized for 3D printing, the preview pictures of which you see above.

It is recommended:

  • to print Version 1 STL files on FDM/FFF 3D printers;
  • to print Version 2 STL files on DLP/SLA/SLS 3D printers.
File Name File Size Time / Filament
1_Hulk_sls.STL
50.62 MiB 50 h 39 min
36 m
Download

HISTORY OF THE HULK

The Hulk is a huge green fierce creature. His name is Bruce Banner and Hulk is the opposite manifestation of his emotional essence. Because of his huge anger and lack of self-control he was deported from Earth. The ship had to make a landing on a deserted planet without intelligent creatures, but the furious Hulk, smashing the engines, knocked down the course of the ship, and it crashed on the inhabited planet of Sakaar. Local residents take the Hulk as a prisoner and make him a gladiator. And for your attention is presented his version of the gladiator. Completely in armor and with weapons in hands, his pose shows his ferocity. Ferocity is the only thing that remains for him since in the form of the Hulk he does not have much intelligence, although his first personality is one of the cleverest people on earth. He meets in a duel with Thor and there he showed himself in this magnificent armor. The inspiration for creating this model was taken from comic books and now check what we've got…

ABOUT THIS 3D MODEL

Armored Hulk 3D model for printing was created in ZBrush. The model is saved in STL files, a format supported by most 3D printers. 

FDM version features
- Contain 16 parts.
- Made with connectors.
- The weapons are removable and inserted into the hands so that you can print them separately and combine at will.
- All parts are divided in such way that you will print them with the smallest amount of supports.

SLS/SLA version features:
-Same as FDM but smaller and made as 1 part, for economy your material.

All .STL files for 3D printing have been checked in Netfabb and no errors were shown.

Note: Before starting 3D printing the model, read the Printing Details for CURA 2.7.0. Software.

There are 16 parts for FDM version and only 1 part for SLS/SLA version.

All parts of connectors should be printed at 100% infill.

Scale
His scale is taken on the basis of the size of middle rage - 2456 mm. Model made as 1/8 scale in FDM version and 1/16 in SLS/SLA version.

FDM version dimensions:
- After being printed will stand 307 mm tall, 470 mm wide, 185 mm deep;
- Connectors should be printed at 100% infill to make them solid.

SLS/SLA version dimensions:
- After being printed will stand 154 mm tall, 235 mm wide, 92.6 mm deep;
- Has only one detail to keep printing costs down.

WHAT WILL YOU GET AFTER PURCHASE?

- .STL files of Armored Hulk for 3D printing which consist of 17 parts.
- 2 versions of files for this model for FFF/FDM and SLS/SLA.
- High-poly detailed model of Armored Hulk.
- Made in scale 1/8 and 1/16 of his middle rage size. 
- Detailed settings that we provide for Cura 2.7.0. for the best print.
- Full technical support from the Gambody Support Team.

Watch the tutorial video on how to assemble Armored Hulk 3D Printing Miniature at Gambody YouTube channel

You can get Armored Hulk Model for 3D Printing right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Also, you may like another Heroes 3D models.

_______
FAQ: 

Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 2.7.0. and printed on an Ultimaker 2 in PLA material.

Note: To maintain model quality, do not try to increase or decrease the size, since the connectors may not fit and the model will not be assemble after scale changes.

To avoid printing problems, we recommend the following settings:

Quality 
Layer Height: 0.1 mm
Initial Layer Height: 0.27 mm
Line Width: 0.35 mm
Wall Line Width: 0.35 mm
   Outer Wall Line Width: 0.35 mm
   Inner Wall(s) Line Width: 0.35 mm
   Top/Bottom Line Width: 0.35 mm
   Infill Line Width: 0.35 mm
   Skirt/Brim Line Width: 0.35 mm
   Support Line Width: 0.35 mm
 Initial Layer Line Width: 100%

Shell 
Wall Thickness: 1.05 mm
Wall Line Count: 3
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0.025 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Shortest
Ignore Small Z Gaps: Check

Infill 
Infill Density: 20% (all parts of the connectors should be printed at 100% infill)
Infill Line Distance: 3.5 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill Overlap Percentage: 10%
    Infill Overlap: 0.035 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.0175 mm
Infill Wipe Distance: 0.0875 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2

Material 
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.7 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 20 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Speed 
Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 36 mm/s
      Outer Wall Speed: 26 mm/s
      Inner Wall Speed: 36 mm/s
    Top/Bottom Speed 20 mm/s
    Support Speed: 26 mm/s
      Support Infill Speed: 26 mm/s
Travel Speed: 90 mm/s
Initial Layer Speed: 27 mm/s

    Initial Layer Print Speed: 27 mm/s
    Initial Layer Travel Speed: 54 mm/s
Skirt/Brim Speed: 27 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Travel 
Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.6562 mm 

Cooling 
Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.27 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Support 
Enable Support: Check
Support Placement: Everywhere
Support Overhang Angle: 50°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 2.3333 mm
Support Z Distance: 0.1 mm
    Support Top Distance: 0.1 mm
    Support Bottom Distance: 0.1 mm
Support X/Y Distance: 0.7 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.2 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 23 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Experimental 
Extra Skin Wall Count: 0

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Comments

comments powered by Disqus

Similar items

Browse more newly listed 3D printings