This should take overall.
Dogmatix 3D Printing Figurine for Diorama | Assembly
This 3D Miniature consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.
Before printing the files, we strongly recommend reading the PRINTING DETAILS section.
|File Name||File Size||Time / Filament||Object Size
1_platform_1 (repaired).s tl
||7.11 MiB||36 h 10 min 21 m||158 x 158 x 46||Download|
2_platform_2 (repaired).s tl
||6.43 MiB||32 h 24 min 18 m||159 x 158 x 35||Download|
3_platform_3 (repaired).s tl
||5.94 MiB||31 h 11 min 18 m||158 x 158 x 33||Download|
4_platform_4 (repaired).s tl
||6.25 MiB||31 h 51 min 18 m||159 x 158 x 32||Download|
5_Ge_lock_7S (x36) (repai red).stl
||0.02 MiB||3 min <1 m||7 x 18 x 2||Download|
||5.77 MiB||14 h 29 min 10 m||89 x 72 x 142||Download|
7_dogmatix_on_log (repair ed).stl
||8.34 MiB||12 h 20 min 8 m||78 x 109 x 84||Download|
8_dogmatix_Head (repaired ).stl
||1.90 MiB||44 min <1 m||Download|
9_dogmatix_Body (repaired ).stl
||2.35 MiB||48 min <1 m||23 x 29 x 26||Download|
||8.68 MiB||10 h 44 min 7 m||78 x 109 x 61||Download|
11_signpost_1 (repaired). stl
||4.35 MiB||6 h 16 min 4 m||45 x 42 x 142||Download|
12_signpost_2 (repaired). stl
||2.51 MiB||3 h 12 min 2 m||16 x 46 x 88||Download|
13_signpost_3 (repaired). stl
||1.84 MiB||2 h 8 min 1 m||21 x 38 x 71||Download|
||5.66 MiB||3 h 16 min 2 m||53 x 26 x 78||Download|
||1.12 MiB||28 min <1 m||Download|
||1.78 MiB||1 h 2 min 1 m||23 x 27 x 25||Download|
Sending to ...
DIORAMA FOR ASTERIX AND OBELIX WITH DOGMATIX
This diorama displays the terrain of the journey of our heroes Asterix and Obelix. You can decorate it under your favorite terrain of their travels such as snow, desert, forest or the village of Gaul. And this platform also contains their faithful satellite Idefix expert on finding a way out of the pyramids.
ABOUT THIS DIORAMA
This diorama is saved in STL files, a format supported by most 3D printers.
- Contains 16 parts;
- Made with Locks. One part of Lock you need to print 36 times for good fixing;
- Contains elements of Romans armor;
- Contains Dogmatix 3D Miniature, the little canine pal of Obelix;
- All parts are divided in such way that you will print them with the smallest amount of supports.
All STL files for 3D printing have been checked in Netfabb and no errors were shown.
Note: Before starting 3D printing the model, read the Printing Details for CURA 3.1.0. Software.
Scale: The scale of the model was calculated on the basis of the growth of the Dogmatix breed (west highland white terrier) 25 cm. So the size of diorama is 3500 mm. Model made as 1/12 scale.
After being printed will stand: 163 mm tall, 316 mm wide, 316 mm deep;
WHAT WILL YOU GET AFTER PURCHASE?
- STL files of Diorama for 3D printing which consist of 16 parts;
- Contains elements of Romans armor and made with Locks;
- High-poly detailed Dogmatix 3D Miniature, the little canine pal of Obelix
- High-poly detailed elements of diorama;
- Detailed settings that we provide for Cura 3.1.0. for the best print;
- Full technical support from the Gambody Support Team.
Watch the tutorial video on how to assemble 3D Printing Miniature of this diorama at Gambody YouTube channel.
You can get Diorama for your models of Asterix and Obeix right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.
Here you can find main heroes: Asterix and his friend Obelix.
Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning?
How to paint printed figurine?
This model was tested in Cura 3.1.0. and printed on an Ultimaker 2 in PLA material.
Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.
To avoid printing problems, we recommend the following settings:
Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Slicing Tolerance: Middle
Line Width: 0.4 mm
Wall Line Width: 0.4 mm
Outer Wall Line Width: 0.4 mm
Inner Wall(s) Line Width: 0.4 mm
Top/Bottom Line Width: 0.4 mm
Infill Line Width: 0.4 mm
Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
Initial Layer Line Width: 100%
Wall Thickness: 0.8 mm
Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
Top Thickness: 0.8 mm
Top Layers: 8
Bottom Thickness: 0.8 mm
Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
Compensate Outer Wall Overlaps: Check
Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1
Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
Top Skin Removal Width: 0.8 mm
Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
Top Skin Expand Distance: 0.8
Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
Minimum Skin Width for Expansion: 0.0
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
Nozzle Switch Retract Speed: 20 mm/s
Nozzle Switch Prime Speed: 20 mm/s
Print Speed: 45 mm/s
Infill Speed: 50 mm/s
Wall Speed: 22.5 mm/s
Outer Wall Speed: 22.5 mm/s
Inner Wall Speed: 45 mm/s
Top/Bottom Speed: 15 mm/s
Support Speed: 45 mm/s
Support Infill Speed: 45 mm/s
Travel Speed: 80 mm/s
Initial Layer Speed: 15 mm/s
Initial Layer Print Speed: 15 mm/s
Initial Layer Travel Speed: 26.6667 mm/s
Skirt/Brim Speed: 15 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2
Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm
Enable Print Cooling: Check
Fan Speed: 100%
Regular Fan Speed: 100%
Maximum Fan Speed: 100%
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
Regular Fan Speed at Layer: 2
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s
Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
Support Line Distance: 1.3333 mm
Support Z Distance: 0.3 mm
Support Top Distance: 0.3 mm
Support Bottom Distance: 0.3 mm
Support X/Y Distance: 0.7 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.2 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65°
Build Plate Adhesion
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
Brim Line Count: 18
Brim Only on Outside: Check
Union Overlapping Volumes: Check
Maximum Resolution: 0.01 mm
Merged Meshes Overlap: 0.15 mm
Print Sequence: All at Once
Surface Mode: Normal
Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.
From the same author:
Inappropriate Content Form
You are about to report Dogmatix 3D Printing Figurine for Diorama | Assembly for violating our Terms and Conditions. Please take a few moments to fill in the following information.
Commentscomments powered by Disqus