Premium Stock

Obelix 3D Printing Figurine for Diorama | Assembly

cm: 11 w x 16.3 d x 27.1 h
in: 4.331 w x 6.417 d x 10.669 h

Source Files




Printing Details

This 3D Miniature consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
1_obelix_hair_R (repaired ).stl
0.85 MiB 11 min <1 m 15 x 7 x 23 Download
2_obelix_Top (repaired).s tl
7.98 MiB 12 h 2 min 7 m 97 x 60 x 83 Download
3_obelix_hair_L (repaired ).stl
0.83 MiB 12 min <1 m 15 x 9 x 22 Download
4_obelix_arm_R (repaired) .stl
2.55 MiB 2 h 33 min 1 m 32 x 29 x 77 Download
5_obelix_arm_L (repaired) .stl
2.49 MiB 2 h 43 min 2 m 30 x 29 x 73 Download
7_Ge_lock_7S (x7) (repair ed).stl
0.02 MiB 3 min <1 m 7 x 18 x 2 Download
9_obelix_legs (repaired). stl
11.57 MiB 25 h 13 min 16 m 90 x 89 x 101 Download
10_obelix_foot_R (repaire d).stl
0.94 MiB 45 min <1 m 36 x 32 x 22 Download
11_obelix_foot_L (repaire d).stl
0.82 MiB 42 min <1 m 32 x 39 x 15 Download
12_obelix (repaired).stl
20.81 MiB 50 h 9 min 33 m 104 x 119 x 160 Download
13_rock (repaired).stl
16.27 MiB 55 h 15 min 34 m 99 x 163 x 184 Download
14_Ge_lock_10H4_(X4)_for_ rock (repaired).stl
0.03 MiB 4 min <1 m 10 x 18 x 2 Download
6_rock_1 (repaired).stl
9.45 MiB 32 h 6 min 20 m 92 x 93 x 103 Download
8_rock_2 (repaired).stl
7.11 MiB 21 h 53 min 13 m 86 x 84 x 130 Download


Obelix is ​​a fictional Gaul warrior a character in the comic book series of animated and feature films and computer games about Asterix. He has huge strength because he because in his childhood he fell into the pot with a magical potion. Unlike the rest of the galls that need to drink a potion to gain strength for a while, he has it constantly. He is not very smart and likes to eat tasty boars. Although he can not always make a plan and act cunningly, he is a very good friend to the asterix and together they are an excellent team.


The model is saved in STL files, a format supported by most 3D printers. 


- Contains 13 parts;

- Made with Locks. One part of Lock you need to print 7 times;

- Contain one-piece variant. Made with his favourite rock;

- All parts are divided in such way that you will print them with the smallest amount of supports.

All STL files for 3D printing have been checked in Netfabb and no errors were shown.

Note: Before starting 3D printing the model, read the Printing Details for CURA 3.1.0. Software.

Scale: The scale of the model was calculated on the basis of the growth of the Dogmatix breed (west highland white terrier) 25 cm. So the size of Obelix with rock is 3250 mm. Model made as 1/12 scale.


After being printed will stand:
 271 mm tall, 110 mm wide, 163 mm deep;


- STL files of Obelix for 3D printing which consists of 13 parts;

- Contain one-piece variant;
- High-poly detailed miniature of Obelix;

- Detailed settings that we provide for Cura 3.1.0. for the best print;

- Full technical support from the Gambody Support Team.

Watch the tutorial video on how to assemble Obelix 3D Printing Miniature at Gambody YouTube channel.  

You can get Model of Obelix for 3D Printing right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Here you can find his little canine pal Dogmatix and his friend Asterix.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?


This model was tested in Cura 3.1.0. and printed on an Ultimaker 2 in PLA material.

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

To avoid printing problems, we recommend the following settings:


Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Slicing Tolerance: Middle
Line Width: 0.4 mm
Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
   Top/Bottom Line Width: 0.4 mm
   Infill Line Width: 0.4 mm
   Skirt/Brim Line Width: 0.4 mm
   Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%


Wall Thickness: 0.8 mm
Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1


Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0


Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 


Print Speed: 45 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s
      Support Infill Speed: 45 mm/s
Travel Speed: 80 mm/s
Initial Layer Speed: 15 mm/s

    Initial Layer Print Speed: 15 mm/s
    Initial Layer Travel Speed: 26.6667 mm/s
Skirt/Brim Speed: 15 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2


Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm 
Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s


Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 1.3333 mm
Support Z Distance: 0.3 mm
    Support Top Distance: 0.3 mm
    Support Bottom Distance: 0.3 mm
Support X/Y Distance: 0.7 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.2 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 

Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 18 
Brim Only on Outside: Check

Mesh Fixes 

Union Overlapping Volumes: Check
Maximum Resolution: 0.01 mm
Merged Meshes Overlap: 0.15 mm

Special Modes

Print Sequence: All at Once
Surface Mode: Normal

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.


comments powered by Disqus

Similar items

Browse more newly listed 3D printings