Make pre-order

Greenskins Catapult 3D Printing Miniatures | Assembly

small
cm: 7.5 w x 7.5 d x 9.1 h
in: 2.953 w x 2.953 d x 3.583 h
8
BUY FOR  $24.99

Source Files

|

Description

|

Printing Details

These 3D Miniatures consist of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Greenskins Catapult 3D Printing Miniatures come in one version for DLP/SLA/SLS 3D printer types. Files for 3D printing are available for download after the purchase.

Detailed information about these 3D printing miniatures is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
1_Goblin_1 (repaired).stl
58.91 MiB 52 min
<1 m
20 x 22 x 23 Download
2_Goblin_2 (repaired).stl
48.99 MiB 43 min
<1 m
21 x 19 x 27 Download
3_Goblin_3 (repaired).stl
41.46 MiB 44 min
<1 m
15 x 14 x 43 Download
4_Goblin_4 (repaired).stl
13.65 MiB 11 min
<1 m
11 x 10 x 11 Download
5_goblin_base_x3 (repaire d).stl
2.31 MiB 15 min
<1 m
26 x 26 x 3 Download
6_platform_full (repaired ).stl
0.24 MiB 2 h 3 min
1 m
75 x 75 x 3 Download
7_platform_a (repaired).s tl
0.17 MiB 1 h 5 min
1 m
43 x 75 x 3 Download
8_platform_b (repaired).s tl
0.12 MiB 1 h 4 min
1 m
37 x 75 x 3 Download
9_wheel_a_R (repaired).st l
0.77 MiB 15 min
<1 m
8 x 13 x 13 Download
10_wheel_b_R (repaired).s tl
1.28 MiB 20 min
<1 m
8 x 16 x 16 Download
11_wheel_c_R (repaired).s tl
0.77 MiB 15 min
<1 m
8 x 13 x 13 Download
12_wheel_a_L (repaired).s tl
0.78 MiB 14 min
<1 m
8 x 13 x 13 Download
13_wheel_b_L (repaired).s tl
1.46 MiB 20 min
<1 m
8 x 16 x 16 Download
14_wheel_c_L (repaired).s tl
0.81 MiB 14 min
<1 m
8 x 13 x 13 Download
15_base_a_R (repaired).st l
43.32 MiB 1 h 4 min
1 m
25 x 12 x 39 Download
16_base_a_L (repaired).st l
27.49 MiB 1 h 4 min
1 m
26 x 12 x 39 Download
17_base_b_R (repaired).st l
10.14 MiB 22 min
<1 m
13 x 10 x 19 Download
18_base_b_L (repaired).st l
6.69 MiB 20 min
<1 m
13 x 10 x 19 Download
19_base_center_a (repaire d).stl
2.94 MiB 10 min
<1 m
13 x 4 x 10 Download
20_base_center_b (repaire d).stl
7.83 MiB 8 min
<1 m
13 x 27 x 2 Download
21_base_center_c (repaire d).stl
1.08 MiB 4 min
<1 m
13 x 4 x 4 Download
22_base_center_d (repaire d).stl
3.39 MiB 12 min
<1 m
13 x 18 x 5 Download
23_base_center_e (repaire d).stl
11.63 MiB 5 min
<1 m
13 x 8 x 4 Download
24_base_center_f (repaire d).stl
3.45 MiB 7 min
<1 m
13 x 7 x 7 Download
25_beam_a_R (repaired).st l
5.96 MiB 34 min
<1 m
6 x 31 x 27 Download
26_beam_a_L (repaired).st l
6.24 MiB 31 min
<1 m
6 x 31 x 27 Download
27_beam_b_R (repaired).st l
64.84 MiB 20 min
<1 m
17 x 61 x 4 Download
28_beam_b_L (repaired).st l
4.52 MiB 13 min
<1 m
19 x 35 x 4 Download
29_loop_R (repaired).stl
5.90 MiB 3 min
<1 m
5 x 9 x 5 Download
30_loop_L (repaired).stl
5.09 MiB 3 min
<1 m
5 x 9 x 5 Download
31_Flag_1 (repaired).stl
4.67 MiB 8 min
<1 m
10 x 18 x 6 Download
32_Flag_2 (repaired).stl
6.69 MiB 11 min
<1 m
10 x 18 x 16 Download
33_Flag_3 (repaired).stl
4.72 MiB 17 min
<1 m
12 x 18 x 15 Download
34_rope_1 (repaired).stl
1.87 MiB 3 min
<1 m
7 x 8 x 4 Download
35_rope_2 (repaired).stl
2.50 MiB 12 min
<1 m
6 x 58 x 9 Download
36_rope_3 (repaired).stl
5.90 MiB 23 min
<1 m
6 x 72 x 21 Download
37_launcher_a (repaired). stl
8.95 MiB 40 min
<1 m
14 x 37 x 37 Download
38_launcher_b (repaired). stl
20.24 MiB 26 min
<1 m
18 x 10 x 13 Download
39_launcher_c (repaired). stl
3.76 MiB 7 min
<1 m
6 x 11 x 7 Download
40_Stone_counter_weight ( repaired).stl
3.34 MiB 7 min
<1 m
9 x 15 x 8 Download
41_loop_for_your_string ( repaired).stl
0.94 MiB 1 min
<1 m
4 x 3 x 3 Download
Keychain (repaired).stl
0.35 MiB 23 min
<1 m
30 x 30 x 2 Download
Tag (repaired).stl
1.70 MiB 1 h 16 min
1 m
150 x 18 x 5 Download

ABOUT THESE 3D MINIATURES

Small, mischievous and resourceful creatures Goblins are known to have their origins in European folklore and still can be encountered in various fictional universes. Fantasy movies or adventurous video and board games teem with all kinds of monstrous representatives who are usually up to no good. Goblins may be weaker and smaller than their foes but they make up for this lack of strength by pretty surprising inventive skills. The author of the Greenskins Catapult model for 3D printing is also convinced that although Goblins may not be the brightest engineers, the tiny creatures are capable of manufacturing impressive war machines, just like this Catapult for 3D printing. Therefore, being inspired by medieval fiction, the 3D artist spent 78 hours in total to create an amusing rock launching scene for 3D printing that would be an excellent addition to any fantasy scenario! We’ve got four Goblin miniatures, each engaged in a particular activity. One is depicted to be in charge of operating the Catapult, the other is about to load a heavy rock into the launcher’s bucket. The 3D printing scene also seems to feature the pair of battle supervisors - one monster is portrayed as if about to lash the lagging teammate, the fourth one is on the look-out. Due to the fact that three of the Goblins have their own little platforms, you are free to arrange the characters of the scene just the way that your scenario needs them to be. Don’t hesitate to add the real Goblin-made catapult to your tabletop game - the STL files are ready for download.

ADAPTATION FOR 3D PRINTING

Greenskins Catapult for 3D printing is a set of static miniatures of goblins and an assembly RocksLauncher that when printed form a versatile scene for your fantasy board game. The one-piece creatures, as well as their assembly catapult, were intended by the author as the miniatures that are meant to be printed on DLP/SLA or SLS 3D printers in order to preserve the quality of the design. The unit’s moderation process took Gambody team 27 hours in total and during the review, the creatures’ proportions were checked, the needed improvements were introduced and it was made sure that all the miniatures’ fine details are printable. The cutting of the Catapult model was chosen for you to achieve the cleanest result possible. Therefore, such smaller parts as launcher’s beam, frame, counterweight, ropes, wheels, flags etc. are provided as separate files. All the catapult’s assembly parts come in STL files in recommended positions that were worked out in order to ensure the smoothness of the details’ surfaces after printing and that the 3D printing beginners won't face difficulties when placing the parts on a build plate.  

The miniatures are saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The miniatures' scale was calculated from Greenskins' height that is approximately 500 mm. The 3D printing miniatures are available in 1/16 scale for the DLP/SLA/SLS version.

VERSION SPECIFICATIONS

DLP/SLA/SLS 1.0 version features:
- Contains 41 parts: an assembly RocksLauncher and 4 solid one-piece goblin miniatures;
- A printed Greenskin miniature is 46 mm tall, 26 mm wide, 26 mm deep;
- A printed Catapult stands 91 mm tall, 75 mm wide, 75 mm deep;
- Each miniature, as well as the whole RocksLauncher, is placed on a platform for you to easily introduce new items into your thematic tabletop game.

WHAT WILL YOU GET AFTER PURCHASE?

- STL files of Greenskins Catapult 3D Miniatures for 3D printing which consist of 41 parts;
- 1 version of files for the miniatures for DLP/SLA and SLS;
- High-poly detailed miniatures of Greenskins Catapult​;
- Detailed settings that we provide as a recommendation for Cura 3.5.1, Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get the miniatures of Greenskins Catapult​ for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Greenskins Catapult 3D Printing Miniatures at Gambody YouTube channel.

Also, you may like other Orc 3D Printing Figurines or Squiggly Beasts Miniatures for 3D Printing.

_______
FAQ: 

Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

If you want to 3D print this miniature on an FDM 3D printer, we recommend scaling the model up three times and use the CuraSimplify3D or Slic3r settings below.

Cura printing recommendations:

To avoid printing problems, we recommend the following settings:

Quality
Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Shell 
Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill 
Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Material 
Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Speed 
Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s 
     Support Infill Speed: 45 mm/s
Travel Speed: 45 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 45 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Travel 
Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.6562 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Cooling 
Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Support 
Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 2.2 mm
Support Z Distance: 0.13 mm
    Support Top Distance: 0.13 mm
    Support Bottom Distance: 0.13 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 15 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Experimental
Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Extruder
Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Layer
Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Additions
Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Infill
Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Support
Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Temperature
Extruder 1 Temperature: 210
Heated Bed: 60

Cooling
Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Speeds
Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Other
Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
Quality
  Detect thin walls: Check
  Detect bridging perimeters: Check
Advanced
  Seam position: Random
Infill
  Fill desity: 20%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
Advanced
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
Skirt
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
Brim 
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
Raft
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
Modifiers
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
Autospeed
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
Overlap
  Infill/Perimeters overlap: 20%
Flow
  Bridge flow ratio: 0.95
Other
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm

Comments

comments powered by Disqus

Similar items

Browse more newly listed 3D printings