Make pre-order

cm: 12.5 w x 5.8 d x 18.7 h
in: 4.921 w x 2.283 d x 7.362 h
BUY FOR  $19.99

Source Files




Printing Details

This 3D model consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Version 1 and Version 2 are the files for Princess Leia 3D Model optimized for 3D printing, the preview pictures of which you see above.

It is recommended:

  • to print Version 1 STL files on FDM/FFF 3D printers;
  • to print Version 2 STL files on DLP/SLA/SLS 3D printers.
File Name File Size Time / Filament
1.96 MiB 36 min
<1 m
20.38 MiB 6 h 43 min
4 m
1.37 MiB 36 min
<1 m
0.03 MiB 6 min
<1 m
0.03 MiB 6 min
<1 m
3.21 MiB 3 h 5 min
2 m
3.30 MiB 1 h 51 min
1 m
2.77 MiB 1 h 25 min
1 m
2.31 MiB 51 min
<1 m
2.58 MiB 50 min
<1 m
3.31 MiB 1 h 16 min
1 m
12_Body_v2_FDM (repaired) .stl
15.16 MiB 5 h 1 min
3 m
13_Head_FDM (repaired).st l
14.80 MiB 1 h 29 min
1 m
14_Glave_v2_1_FDM (repair ed).stl
6.43 MiB 55 min
<1 m
15_Glave_v2_2_FDM (repair ed).stl
5.60 MiB 19 min
<1 m
16_Glave_v2_3_FDM (repair ed).stl
2.30 MiB 6 min
<1 m
17_Glave_v2_4_FDM (repair ed).stl
3.71 MiB 29 min
<1 m


Leia Organa Solo is the daughter of Jedi Knight Anakin Skywalker and Senator Padme Amidala also Luke Skywalker's twin sister. After the birth she was adopted by Bail Organa and Queen Breha, they made her a princess of Alderaan. She received the excellent education of a senator also Organa is known as an unshakable leader during the Galactic Civil War and other subsequent galactic conflicts. Leia became one of the greatest heroes of the galaxy. Later, she married Han Solo and became the mother of three children: Jaina, Jacen and, Anakin. The youngest senator in the Galactic Senate, she secretly supported the rebels and decided to transfer to the Alliance plans for the "Death Star". Despite the unexpected capture of torture and humiliation that Leia endured from Darth Vader, she did not change her ideals of freedom and equality for all residents of the galaxy and became one of the most important insurgents in the Alliance during the Galactic Civil War. Years later, she was elected head of the New Republic and held this post for 2 terms. Also, the Force is powerfully manifested in her. Leia became the knight of the New Order of the Jedi, partly training under the guidance of her brother Luke and later Saba Sebatyne, who declared her a full knight at the end of the War of Troops. These training benefited when the Galaxy began to split during the war between the Confederation and the Galactic Alliance, although it has changed her dedication.


Princess Leia 3D model for printing was created in ZBrush. The model is saved in STL files, a format supported by most 3D printers

FDM version features:

- Contain 11 parts;

- Made with connectors;

- Removable part of the Glaive;

- Removable dress that you can print with flexible materials;

- All parts are divided in such way that you will print them with the smallest amount of supports.

SLS/SLA version features:

- Same as FDM but smaller and made as 1 part.

All .STL files for 3D printing have been checked in Netfabb and no errors were shown.

Note: Before starting 3D printing the model, read the Printing Details for CURA 3.0.4. Software.

There are 11 parts for FFF/FDM version and 1 part for SLS/SLA version.

All parts of connectors should be printed at 100% infill.

Scale: Her tall in life is 1500 mm. Model made as 1/8 scale in FDM version and 1/16 in SLS/SLA version.

FDM version dimensions:

After being printed will stand - 187 mm tall, 125 mm wide, 58 mm deep;

- Connectors should be printed at 100% infill to make them solid.

SLS/SLA version dimensions:

After being printed will stand - 94 mm tall, 62 mm wide, 29 mm deep;

- Has only 1 detail, to keep printing costs down.


- .STL files of Princess Leia for 3D printing which consist of 12 parts;

- 2 versions of files for this model for FFF/FDM and SLS/SLA;

- Removable part of the Glaive in FDM version;

- Removable dress that you can print with flexible materials;

- High-poly detailed model of Princess Leia;

- Detailed settings that we provide for Cura 3.0.4. for the best print;

- Full technical support from the Gambody Support Team.

Watch the tutorial video on how to assemble Princess Leia 3D Printing Miniature at Gambody YouTube channel.  

You can get Model of Princess Leia for 3D Printing right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Also, you may like another Space War 3D models.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.0.4. and printed on an Ultimaker 2 in PLA material.

Note: All parts of connectors should be printed at 100% infill. Glaive should also be printed with 100% infill to make it solid.

To avoid printing problems, we recommend the following settings:

Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
   Top/Bottom Line Width: 0.4 mm
   Infill Line Width: 0.4 mm
   Skirt/Brim Line Width: 0.4 mm
   Support Line Width: 0.4 mm
   Support Interface Line Width: 0.4 mm
   Support Roof Line Width: 0.4 mm
   Support Floor Line Width: 0.4
 Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill Density: 20% (all parts of the connectors should be printed at 100% infill)
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Print Speed: 45 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s
      Support Infill Speed: 45 mm/s
      Support Interface Speed: 30 mm/s
        Support Roof Speed: 30mm/s
        Support Floor Speed: 30 mm/s
Travel Speed: 80 mm/s
Initial Layer Speed: 15 mm/s

    Initial Layer Print Speed: 15 mm/s
    Initial Layer Travel Speed: 26.6667 mm/s
Skirt/Brim Speed: 15 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm 

Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Enable Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 30 %
    Support Line Distance: 1.3333 mm
Support Z Distance: 0.3 mm
    Support Top Distance: 0.3 mm
    Support Bottom Distance: 0.3 mm
Support X/Y Distance: 0.7 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.2 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm

Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 18 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.


comments powered by Disqus
Other author's 3D printings


StarWars, Static, hero, Leia, women, rebelsset, swsets

Similar items

Browse more newly listed 3D printings