Make pre-order

(14)
average
cm: 24.1 w x 30.5 d x 16.5 h
in: 9.488 w x 12.008 d x 6.496 h
21
BUY FOR  $24.99

Source Files

|

Description

|

Printing Details

This 3D model consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Version 1, Version 2 and Version 2.1 are the files for Valkyrie Vendetta 3D Model optimized for 3D printing, the preview pictures of which you see above.

It is recommended:

  • to print Version 1 - low resolution STL files;
  • to print Version 2 - high resolution STL files.
  • to print Version 2.1 - fixation has been improved;
File Name File Size Time / Filament
1_cabine (repaired).stl
1.11 MiB 2 h 6 min
1 m
Download
2_cap_back (repaired).stl
0.04 MiB 2 h 7 min
1 m
Download
3_cap_bottom (repaired).s tl
0.01 MiB 33 min
<1 m
Download
4_cap_top (repaired).stl
0.01 MiB 1 h 15 min
1 m
Download
5_GE_Connector_A_A_x4 (re paired).stl
0.08 MiB 7 min
<1 m
Download
6_gun_wing_L (repaired).s tl
9.21 MiB 1 h 2 min
1 m
Download
7_gun_wing_R (repaired).s tl
2.94 MiB 2 h 18 min
1 m
Download
8_hull_gun_L (repaired).s tl
1.30 MiB 26 min
<1 m
Download
9_hull_gun_R (repaired).s tl
1.30 MiB 27 min
<1 m
Download
10_hull_L (repaired).stl
1.79 MiB 17 h 6 min
10 m
Download
11_hull_nose (repaired).s tl
1.43 MiB 2 h 8 min
1 m
Download
12_hull_R (repaired).stl
1.79 MiB 17 h 1 min
10 m
Download
13_hull_tail (repaired).s tl
2.52 MiB 8 h 20 min
5 m
Download
14_hull_top (repaired).st l
1.16 MiB 2 h 37 min
1 m
Download
15_propeller_L (repaired) .stl
0.90 MiB 16 min
<1 m
Download
16_propeller_R (repaired) .stl
0.90 MiB 16 min
<1 m
Download
17_stand_back (repaired). stl
1.62 MiB 1 h 2 min
1 m
Download
18_stand_front (repaired) .stl
1.50 MiB 36 min
<1 m
Download
19-1_top_gun_1 (repaired) .stl
2.09 MiB 19 min
<1 m
Download
19-2_top_gun_2 (repaired) .stl
0.58 MiB 55 min
<1 m
Download
20_turbine_L (repaired).s tl
37.90 MiB 4 h 29 min
2 m
Download
21_turbine_R (repaired).s tl
37.95 MiB 4 h 27 min
2 m
Download
22_wing_L (repaired).stl
3.40 MiB 4 h 11 min
2 m
Download
23_wing_R (repaired).stl
3.41 MiB 4 h 11 min
2 m
Download
24_wing_stand_L (repaired ).stl
2.32 MiB 1 h 2 min
1 m
Download
25_wing_stand_R (repaired ).stl
2.32 MiB 1 h 2 min
1 m
Download
26_Ge_lock_7S_x63.stl
0.02 MiB 3 min
<1 m
Download
27_base_c (repaired).stl
0.02 MiB 24 min
<1 m
Download
28_C_Claw (repaired).stl
0.17 MiB 22 min
<1 m
Download
29_cap_for_platform (repa ired).stl
0.55 MiB 46 min
<1 m
Download
30_platform_1 (repaired) (repaired).stl
1.42 MiB 13 h 10 min
7 m
Download
31_platform_2 (repaired). stl
0.26 MiB 7 h 9 min
4 m
Download

This attack craft, from the hugely popular video game, is used in dangerous missions and quests. It is known for its vertical take off and landing capabilities.

Equipped with deadly weaponry, such as multi-lasers and missiles, the assault carrier is great support for troopers when being dropped off on the battlefield, firing cover shots to protect the soldiers from enemy’s attacks.This agile craft has powerful armor and it can also be enhanced with additional chaff launchers, infrared systems and ejector seats.

Like Chaplain 3D designValkyrie 3D printing model comes in assembly mode. It is 237 mm depth, 189 mm wide and 73 mm tall. Also, one exciting thing is that you can paint your Valkyrie craft in any color you want. See our TAU XV109 Y'Vahra 3D model if you want more figures from these game series.

The model has been tested by our designers and is error free. The downloadable assembly kit is zipped in .STL file format, supported by all 3D printers. You can print it both on SLA/SLS printers and FFF printers.

To buy Valkyrie Vendetta 3D print design, just click on the green "Buy" button and add it to your shopping cart. You can then proceed to checkout, insert your PayPal or credit card details and download STL files.

________________________

On 16.03.2018 the model files have been optimized. We have added high resolutions STL files for Valkyrie Vendetta 3D Printing Model. They now are already available for purchase and download in Version 2.

 

Valkyrie Vendetta 3D Model was revived and got a new version for 3D printing. Changes came to all its details. Now it is available in Version 2 with all possible innovations to improve its quality. Here is a list of changes and improvements:


- The main body was separated into several parts for better printing;
- All elements of the model were divided in such a way to print them more accurately and get a nicer model after printing and assembling it;
- Excellent platform with a ball joint, that gives you the opportunity to set your model in any position you like;
- Great docking elements that will allow your model to stand perfectly on the surface without a platform;
- All STL files have been checked and repaired in Netfabb and no errors were shown;
- All parts are divided in such a way that you will print them with the smallest amount of supports.
- Model fixed by the Locks and Connectors. One part of Lock (26_Ge_lock_7S_x63 (repaired)) you need to print 63 times. One part of Connector (5_GE_Connector_A_A_x4 (repaired)) you need to print 4 times;

New Version 2 contains 31 parts. All parts of Connectors should be printed with 100% infill.

Dimensions: 
After being printed will stand:
165 mm tall, 241 mm wide, 305 mm deep - with platform;
93 mm tall, 241 mm wide, 305 mm deep - without platform;

STL files of new Version 2 are already available for download in “Source files” tab for:
- to print Version 2 - high resolution STL files.

Watch the tutorial video on how to assemble Valkyrie Vendetta 3D Printing Model at Gambody YouTube channel

________________________

On 21.09.2018 the model files get update of fixing parts. 

The model has been improved in general:
1. Now there is a smaller gap between the platform parts, and better fitting assembly improves the platform’s durability.
2. Increased width of the locks helps better fix parts together.
3. The ship’s nose is now closer to the model, with a minimal gap between the nose and connected elements.
4. Bigger side cannons allow better printing of the detailing of the smaller elements.
5. Now divided into two parts, the top gun can be printed with less support that is easier to remove.

The update makes the model’s printing process simpler overall an ensures better fixation for the assembly parts

STL files of new version are already available for download in “Source files” tab for FFF/FDM 2.1 version.

_______
FAQ: 

Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.4.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for CuraSimplify3D and Slic3r softwares.

Cura printing recommendations:

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

Use 100% infill for parts of connectors.

To avoid printing problems, we recommend the following settings:

Quality
Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Shell
Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill
Infill Density: 20% (use 100% infill for all parts of connectors)
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Material
Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s

Speed 
Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
Travel Speed: 45 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 30 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Travel 
Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Cooling 
Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100%
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Support 
Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 50°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 2 mm
Support Z Distance: 0.2 mm
    Support Top Distance: 0.2 mm
    Support Bottom Distance: 0.2 mm
Support X/Y Distance: 0.7 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65°

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 18
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Experimental
Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Extruder
Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Layer
Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Additions
Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Infill
Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Support
Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Temperature
Extruder 1 Temperature: 210
Heated Bed: 60

Cooling
Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Speeds
Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Other
Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
Quality
  Detect thin walls: Check
  Detect bridging perimeters: Check
Advanced
  Seam position: Random
Infill
  Fill desity: 20%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
Advanced
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
Skirt
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
Brim 
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
Raft
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
Modifiers
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
Autospeed
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
Overlap
  Infill/Perimeters overlap: 20%
Flow
  Bridge flow ratio: 0.95
Other
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm

Comments

comments powered by Disqus
Other author's 3D printings

Tags

Warhammer, Valkyrie Vendetta, Ship, Game model, Static

Similar items

Browse more newly listed 3D printings