Make pre-order

Chappie 3D Printing Model | Assembly + Active

average
cm: 35.3 w x 34.1 d x 47.2 h
in: 13.898 w x 13.425 d x 18.583 h

Source Files

|

Description

|

Printing Details

This 3D Figurine of Chappie the Robot consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

WHAT WILL YOU GET AFTER PURCHASE?

- 2 versions of Chappie STL files for FFF/FDM and DLP/SLA printers - all files are available for download after the purchase

- STL files of high-poly Chappie 3D Model for 3D printing consist of 320 parts
- Sizes:
FFF/FDM and DLP/SLA: 472 mm tall, 353 mm wide, 341 mm deep

Assembly Manual for FFF/FDM 1.0 and DLP/SLA 1.0 version in PDF format
- Detailed settings that we provide as a recommendation for Cura, Simplify3D, Slic3r and PrusaSlicer for the best print
- Full technical support from the Gambody Support Team

Detailed information about this 3D printing model is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
_1_foot_R (repaired).stl
11.10 MiB 4 h 6 min
2 m
32 x 73 x 31 Download
_2_foot_connector_a_R (re paired).stl
0.27 MiB 15 min
<1 m
10 x 10 x 16 Download
_3_foot_connector_b_R (re paired).stl
1.22 MiB 12 min
<1 m
16 x 17 x 7 Download
_4_foot_connector_c_R (re paired).stl
0.50 MiB 17 min
<1 m
13 x 14 x 11 Download
_5_foot_L (repaired).stl
11.10 MiB 4 h 5 min
2 m
32 x 73 x 31 Download
_6_foot_connector_a_L (re paired).stl
0.27 MiB 15 min
<1 m
10 x 10 x 16 Download
_7_foot_connector_b_L (re paired).stl
1.23 MiB 12 min
<1 m
16 x 17 x 7 Download
_8_foot_connector_c_L (re paired).stl
0.50 MiB 16 min
<1 m
13 x 14 x 11 Download
_9_shin_R (repaired).stl
9.25 MiB 9 h 20 min
6 m
30 x 48 x 113 Download
_10_shin_connector_a_R (r epaired).stl
0.18 MiB 36 min
<1 m
13 x 17 x 27 Download
_11_shin_connector_b_R (r epaired).stl
0.10 MiB 32 min
<1 m
26 x 48 x 7 Download
_12_shin_connector_c_R (r epaired).stl
0.03 MiB 5 min
<1 m
13 x 6 x 5 Download
_13_shin_stripe_assembly_ R (repaired).stl
0.25 MiB 15 min
<1 m
17 x 68 x 7 Download
_14_shin_stripe_R (repair ed).stl
0.26 MiB 13 min
<1 m
1 x 80 x 7 Download
_15_shin_L (repaired).stl
9.28 MiB 9 h 16 min
5 m
30 x 48 x 113 Download
_16_shin_connector_a_L (r epaired).stl
0.18 MiB 36 min
<1 m
13 x 17 x 27 Download
_17_shin_connector_b_L (r epaired).stl
0.10 MiB 33 min
<1 m
26 x 48 x 7 Download
_18_shin_connector_c_L (r epaired).stl
0.03 MiB 5 min
<1 m
13 x 6 x 5 Download
_19_shin_stripe_assembly_ L (repaired).stl
0.25 MiB 15 min
<1 m
17 x 68 x 7 Download
_20_shin_stripe_L (repair ed).stl
0.26 MiB 13 min
<1 m
1 x 80 x 7 Download
_21_leg_a_R (repaired).st l
0.37 MiB 8 h 8 min
5 m
32 x 44 x 78 Download
_22_leg_b_R (repaired).st l
1.14 MiB 7 h 34 min
5 m
34 x 48 x 71 Download
_23_leg_c_R (repaired).st l
2.90 MiB 40 min
<1 m
13 x 16 x 30 Download
_24_leg_connector_a_R (re paired).stl
1.64 MiB 50 min
<1 m
18 x 18 x 20 Download
_25_leg_connector_b_R (re paired).stl
2.23 MiB 31 min
<1 m
25 x 28 x 11 Download
_26_leg_connector_c_R (re paired).stl
2.93 MiB 23 min
<1 m
12 x 12 x 23 Download
_27_leg_a_L (repaired).st l
0.37 MiB 8 h 7 min
5 m
32 x 44 x 78 Download
_28_leg_b_L (repaired).st l
1.14 MiB 7 h 32 min
5 m
34 x 48 x 71 Download
_29_leg_c_L (repaired).st l
2.90 MiB 42 min
<1 m
13 x 16 x 30 Download
_30_leg_connector_a_L (re paired).stl
1.64 MiB 48 min
<1 m
18 x 18 x 20 Download
_31_leg_connector_b_L (re paired).stl
2.23 MiB 32 min
<1 m
25 x 28 x 11 Download
_32_leg_connector_c_L (re paired).stl
2.93 MiB 24 min
<1 m
12 x 12 x 23 Download
_33_pelvis_bot_R (repaire d).stl
20.07 MiB 4 h 59 min
3 m
61 x 57 x 34 Download
_34_pelvis_bot_L (repaire d).stl
19.99 MiB 5 h 2 min
3 m
61 x 57 x 34 Download
_35_pelvis_bot_mechanism_ a (repaired).stl
0.51 MiB 46 min
<1 m
23 x 25 x 20 Download
_36_pelvis_bot_mechanism_ a (repaired).stl
0.26 MiB 13 min
<1 m
14 x 14 x 7 Download
_37_pelvis_bot_cap_front (repaired).stl
1.16 MiB 19 min
<1 m
20 x 23 x 5 Download
_38_pelvis_bot_cap_bot (r epaired).stl
0.50 MiB 41 min
<1 m
17 x 14 x 39 Download
_39_pelvis_bot_cap_back ( repaired).stl
0.19 MiB 6 min
<1 m
22 x 9 x 2 Download
_40_pelvis_bot_cap_top (r epaired).stl
5.31 MiB 28 min
<1 m
34 x 32 x 6 Download
_41_pelvis_bot_wire_1 (re paired).stl
0.82 MiB 1 h 1 min
<1 m
17 x 20 x 56 Download
_42_pelvis_bot_wire_2 (re paired).stl
0.82 MiB 1 h 3 min
<1 m
19 x 20 x 56 Download
_43_pelvis_bot_wire_3 (re paired).stl
1.47 MiB 42 min
<1 m
37 x 22 x 44 Download
_44_pelvis_top_a (repaire d).stl
1.11 MiB 1 h 19 min
1 m
17 x 46 x 27 Download
_45_pelvis_top_b (repaire d).stl
2.41 MiB 3 h 38 min
2 m
48 x 58 x 31 Download
_46_pelvis_top_c (repaire d).stl
0.99 MiB 1 h 2 min
<1 m
27 x 11 x 29 Download
_47_pelvis_top_R (repaire d).stl
4.71 MiB 1 h 16 min
1 m
55 x 33 x 8 Download
_48_pelvis_top_L (repaire d).stl
3.49 MiB 1 h 8 min
1 m
55 x 40 x 8 Download
_49_pelvis_top_beams_a_x2 (repaired).stl
0.35 MiB 6 min
<1 m
9 x 9 x 5 Download
_50_pelvis_top_beams_b_x2 (repaired).stl
0.45 MiB 9 min
<1 m
22 x 9 x 7 Download
_51_pelvis_top_cap (repai red).stl
0.25 MiB 24 min
<1 m
Download
_52_pelvis_top_connector_ a (repaired).stl
2.60 MiB 38 min
<1 m
Download
_53_pelvis_top_connector_ b (repaired).stl
0.97 MiB 16 min
<1 m
19 x 20 x 6 Download
_54_body_R (repaired).stl
13.08 MiB 16 h 15 min
10 m
Download
_55_body_L (repaired).stl
13.69 MiB 16 h 42 min
10 m
Download
_56_body_bot_L (repaired) .stl
0.33 MiB 2 h 1 min
1 m
19 x 20 x 55 Download
_57_body_bot_R (repaired) .stl
0.34 MiB 2 h 1 min
1 m
Download
_58_body_back (repaired). stl
0.17 MiB 3 h 48 min
2 m
Download
_59_body_beams_x11 (repai red).stl
0.01 MiB 4 min
<1 m
13 x 4 x 4 Download
_60_body_kit_cap_front_V1 (repaired).stl
0.06 MiB 46 min
<1 m
64 x 24 x 4 Download
_61_body_kit_cap_front_V2 (repaired).stl
0.48 MiB 49 min
<1 m
Download
_62_body_kit_cap_front_V3 (repaired).stl
0.48 MiB 52 min
1 m
Download
_63_body_kit_cap_top (rep aired).stl
0.06 MiB 16 min
<1 m
25 x 22 x 2 Download
_64_body_kit_cap_bot (rep aired).stl
0.02 MiB 15 min
<1 m
12 x 6 x 16 Download
_65_body_kit_cap_back (re paired).stl
5.70 MiB 2 h 27 min
1 m
Download
_66_body_kit_flap_R (repa ired).stl
0.43 MiB 41 min
<1 m
33 x 6 x 41 Download
_67_body_kit_flap_L (repa ired).stl
0.43 MiB 41 min
<1 m
Download
_68_body_kit_grid (repair ed).stl
1.06 MiB 12 min
<1 m
25 x 17 x 3 Download
_69_body_kit_vent_front_R (repaired).stl
0.59 MiB 10 min
<1 m
12 x 11 x 7 Download
_70_body_kit_vent_front_L (repaired).stl
0.59 MiB 10 min
<1 m
12 x 11 x 7 Download
_71_body_kit_vent_back_R (repaired).stl
0.57 MiB 6 min
<1 m
Download
_72_body_kit_vent_back_L (repaired).stl
0.57 MiB 6 min
<1 m
Download
_73_body_kit_light_a_R (r epaired).stl
0.37 MiB 32 min
<1 m
Download
_74_body_kit_light_a_L (r epaired).stl
0.37 MiB 32 min
<1 m
Download
_75_body_kit_light_b (rep aired).stl
0.50 MiB 10 min
<1 m
Download
_76_body_kit_lamp_1 (repa ired).stl
0.11 MiB 16 min
<1 m
26 x 5 x 13 Download
_77_body_kit_lamp_2 (repa ired).stl
0.15 MiB 13 min
<1 m
17 x 18 x 11 Download
_78_body_kit_lamp_3 (repa ired).stl
0.10 MiB 23 min
<1 m
Download
_79_body_kit_lamp_4 (repa ired).stl
0.02 MiB n.a.
n.a.
11 x 9 x 1 Download
_80_head_R (repaired).stl
5.63 MiB 3 h 34 min
2 m
63 x 53 x 16 Download
_81_head_L (repaired).stl
6.04 MiB 3 h 33 min
2 m
63 x 53 x 16 Download
_82_head_beams_x3 (repair ed).stl
0.01 MiB 11 min
<1 m
10 x 3 x 16 Download
_83_head_eyes (repaired). stl
0.95 MiB 30 min
<1 m
27 x 19 x 12 Download
_84_head_eyes_cap (repair ed).stl
0.02 MiB 4 min
<1 m
23 x 5 x 2 Download
_85_head_pipe_a (repaired ).stl
2.59 MiB 45 min
1 m
31 x 49 x 18 Download
_86_head_pipe_b (repaired ).stl
2.34 MiB 26 min
<1 m
32 x 26 x 15 Download
_87_head_cap_R (repaired) .stl
1.29 MiB 29 min
<1 m
26 x 26 x 7 Download
_88_head_cap_L (repaired) .stl
1.29 MiB 29 min
<1 m
26 x 26 x 7 Download
_89_head_anten_a (repaire d).stl
0.17 MiB 1 min
<1 m
2 x 2 x 11 Download
_90_head_anten_b (repaire d).stl
0.23 MiB 3 min
<1 m
4 x 4 x 16 Download
_91_head_vent (repaired). stl
0.63 MiB 5 min
<1 m
7 x 7 x 6 Download
_92_head_ear_R (repaired) .stl
1.22 MiB 12 min
<1 m
36 x 44 x 5 Download
_93_head_ear_L (repaired) .stl
1.22 MiB 12 min
<1 m
41 x 39 x 5 Download
_94_head_ear_connector_x2 (repaired).stl
0.41 MiB 5 min
<1 m
14 x 9 x 5 Download
_95_head_back (repaired). stl
0.67 MiB 27 min
<1 m
20 x 18 x 15 Download
_96_head_bot (repaired).s tl
1.11 MiB 17 min
<1 m
18 x 15 x 10 Download
_97_head_neck_connector_a (repaired).stl
0.86 MiB 10 min
<1 m
16 x 17 x 5 Download
_98_head_neck_connector_b (repaired).stl
0.58 MiB 26 min
<1 m
9 x 9 x 28 Download
_99_head_wire_1_L (repair ed).stl
0.79 MiB 9 min
<1 m
9 x 11 x 39 Download
_100_head_wire_2_L (repai red).stl
0.74 MiB 10 min
<1 m
9 x 11 x 39 Download
_101_head_wire_3_L (repai red).stl
0.79 MiB 20 min
<1 m
14 x 9 x 40 Download
_102_head_wire_1_R (repai red).stl
0.79 MiB 9 min
<1 m
9 x 11 x 39 Download
_103_head_wire_2_R (repai red).stl
0.74 MiB 10 min
<1 m
9 x 11 x 39 Download
_104_head_wire_3_R (repai red).stl
0.79 MiB 19 min
<1 m
14 x 9 x 40 Download
_105_shoulder_connector_a _R (repaired).stl
1.96 MiB 1 h 14 min
1 m
25 x 25 x 32 Download
_106_shoulder_connector_b _R (repaired).stl
0.12 MiB 7 min
<1 m
26 x 9 x 5 Download
_107_shoulder_connector_c _R (repaired).stl
1.16 MiB 1 h 30 min
1 m
25 x 24 x 41 Download
_108_shoulder_connector_a _with_Support_R (repaired ).stl
2.05 MiB 1 h 18 min
1 m
25 x 25 x 32 Download
_109_arm_R (repaired).stl
2.75 MiB 4 h 28 min
2 m
23 x 34 x 58 Download
_110_shoulder_connector_a _L (repaired).stl
1.96 MiB 1 h 14 min
1 m
25 x 25 x 32 Download
_111_shoulder_connector_b _L (repaired).stl
0.12 MiB 7 min
<1 m
26 x 9 x 5 Download
_112_shoulder_connector_c _L (repaired).stl
1.16 MiB 1 h 30 min
1 m
25 x 24 x 41 Download
_113_shoulder_connector_a _with_Support_L (repaired ).stl
2.05 MiB 1 h 19 min
1 m
25 x 25 x 32 Download
_114_arm_L (repaired).stl
2.75 MiB 4 h 31 min
2 m
23 x 34 x 58 Download
_115_hand_connector_a_R ( repaired).stl
0.19 MiB 39 min
<1 m
13 x 17 x 27 Download
_116_hand_connector_b_R ( repaired).stl
2.79 MiB 1 h 27 min
1 m
41 x 22 x 25 Download
_117_hand_connector_c_R ( repaired).stl
0.07 MiB 7 min
<1 m
22 x 6 x 5 Download
_118_hand_R (repaired).st l
2.77 MiB 2 h 53 min
1 m
27 x 27 x 65 Download
_119_elbow_R (repaired).s tl
2.31 MiB 23 min
<1 m
29 x 11 x 22 Download
_120_hand_connector_a_L ( repaired).stl
0.19 MiB 36 min
<1 m
13 x 17 x 27 Download
_121_hand_connector_b_L ( repaired).stl
2.79 MiB 1 h 45 min
1 m
25 x 22 x 41 Download
_122_hand_connector_c_L ( repaired).stl
0.07 MiB 7 min
<1 m
22 x 6 x 5 Download
_123_hand_L (repaired).st l
2.77 MiB 2 h 53 min
1 m
27 x 27 x 65 Download
_124_elbow_L (repaired).s tl
2.31 MiB 23 min
<1 m
29 x 11 x 22 Download
_125_wrist_connector_a_R (repaired).stl
0.39 MiB 15 min
<1 m
15 x 25 x 9 Download
_126_wrist_connector_b_R (repaired).stl
0.44 MiB 11 min
<1 m
12 x 12 x 8 Download
_127_wrist_connector_a_L (repaired).stl
0.39 MiB 14 min
<1 m
15 x 25 x 9 Download
_128_wrist_connector_b_L (repaired).stl
0.44 MiB 11 min
<1 m
12 x 12 x 8 Download
_129_wrist_R (repaired).s tl
1.79 MiB 1 h 35 min
1 m
18 x 27 x 35 Download
_130_wrist_L (repaired).s tl
1.79 MiB 1 h 36 min
1 m
18 x 27 x 35 Download
_130_wrist_L (repaired).s tl
1.79 MiB 1 h 36 min
1 m
18 x 27 x 35 Download
_131_thumb_finger_a_x2 (r epaired).stl
0.20 MiB 5 min
<1 m
13 x 7 x 6 Download
_132_thumb_finger_b_x2 (r epaired).stl
0.55 MiB 8 min
<1 m
16 x 6 x 7 Download
_133_index_finger_a_x2 (r epaired).stl
0.20 MiB 6 min
<1 m
5 x 13 x 6 Download
_134_index_finger_b_x2 (r epaired).stl
0.60 MiB 8 min
<1 m
6 x 16 x 7 Download
_135_index_finger_c_x2 (r epaired).stl
0.61 MiB 8 min
<1 m
6 x 16 x 7 Download
_136_middle_finger_a_x2 ( repaired).stl
0.20 MiB 6 min
<1 m
5 x 13 x 6 Download
_137_middle_finger_b_x2 ( repaired).stl
0.60 MiB 8 min
<1 m
6 x 17 x 7 Download
_138_middle_finger_c_x2 ( repaired).stl
0.61 MiB 8 min
<1 m
6 x 17 x 7 Download
_139_ring_finger_a_x2 (re paired).stl
0.20 MiB 6 min
<1 m
5 x 13 x 6 Download
_140_ring_finger_b_x2 (re paired).stl
0.60 MiB 8 min
<1 m
6 x 15 x 7 Download
_141_ring_finger_c_x2 (re paired).stl
0.61 MiB 8 min
<1 m
6 x 16 x 7 Download
_142_little_finger_a_x2 ( repaired).stl
0.20 MiB 6 min
<1 m
5 x 13 x 6 Download
_143_little_finger_b_x2 ( repaired).stl
0.60 MiB 8 min
<1 m
6 x 15 x 7 Download
_144_little_finger_c_x2 ( repaired).stl
0.61 MiB 8 min
<1 m
6 x 15 x 7 Download
_145_platform_full (repai red).stl
14.36 MiB 59 h 56 min
30 m
281 x 281 x 12 Download
_146_platform_cut_1 (repa ired).stl
3.27 MiB 12 h 33 min
7 m
145 x 140 x 11 Download
_147_platform_cut_2 (repa ired).stl
3.70 MiB 15 h 4 min
8 m
161 x 165 x 12 Download
_148_platform_cut_3 (repa ired).stl
5.38 MiB 18 h 9 min
9 m
164 x 168 x 12 Download
_149_platform_cut_4 (repa ired).stl
3.73 MiB 14 h
7 m
139 x 162 x 11 Download
_150_pin_1 (repaired).stl
0.03 MiB 4 min
<1 m
2 x 61 x 2 Download
_151_pin_2 (repaired).stl
0.03 MiB 2 min
<1 m
2 x 23 x 2 Download
_152_pin_3 (repaired).stl
0.03 MiB 2 min
<1 m
1 x 23 x 1 Download
_153_m4a1_a (repaired).st l
5.86 MiB 1 h 36 min
1 m
12 x 26 x 84 Download
_154_m4a1_b (repaired).st l
2.59 MiB 4 h 34 min
2 m
17 x 55 x 90 Download
_155_m4a1_c (repaired).st l
2.61 MiB 50 min
<1 m
25 x 5 x 54 Download
_156_m4a1_d (repaired).st l
16.56 MiB 2 h 17 min
1 m
12 x 39 x 53 Download
_157_chain_a (repaired).s tl
16.17 MiB 2 h 57 min
2 m
37 x 60 x 67 Download
_158_chain_b (repaired).s tl
24.79 MiB 2 h 5 min
1 m
37 x 45 x 64 Download
_159_chain_c (repaired).s tl
27.59 MiB 2 h 47 min
2 m
39 x 42 x 68 Download
_160_chains_all (repaired ).stl
66.53 MiB 5 h 34 min
4 m
40 x 60 x 69 Download
Keychain (repaired).stl
0.35 MiB 23 min
<1 m
30 x 30 x 2 Download
Tag (repaired).stl
1.70 MiB 1 h 18 min
1 m
150 x 18 x 5 Download

ABOUT THIS 3D MODEL

 "I am consciousness. I am alive. I am Chappie."

Chappie is the titular main protagonist of the 2015 dystopian sci-fi movie, the law enforcement robot gifted with artificial intelligence that mimics a sentimental human. The robot was kidnapped and practically adopted by a pack of gangsters, who guided Chappie through different stages of ageing, taught him how to fight and love, and used the naive creature for dangerous crimes.

Would you have a try at raising a Chappie of your own? Our contributing 3D artist created an immensely detailed and elaborate Chappie 3D Printing Model for you to build the robot in your hobby workshop. Gangster or not, the 3D printed Chappie will be happy to be by your side!

ADAPTATION FOR 3D PRINTING

Chappie for 3D printing is an active assembly model and its moderation and adaptation for different types of 3D printers took the Gambody team 45 hours in total. 

For you to receive the cleanest 3D printing result possible and assemble a fully moveable model, the robot was divided into many assembly parts.

All assembly parts in the FFF/FDM version are provided in STL files in recommended positions that were worked out in order to ensure the smoothness of the details’ surfaces after printing and that the 3D printing beginners won't face difficulties when placing the parts on a build plate. When downloading any model's file you will also receive "Assembly Manual" for FFF/FDM 1.0 and DLP/SLA 1.0 version in PDF format. We highly recommend that you get acquainted with the “Assembly video” and "Assembly Manual" before getting down to the Chappie model.

The model is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model’s scale was calculated from the approximate height of Chappie which is 1800 mm. The 3D printing model’s chosen scale is 1:4 for the FFF/FDM and DLP/SLA versions.

VERSIONS' SPECIFICATIONS

FFF/FDM 1.0 version features:
- Contains 160 parts;
- A printed model stands 472 mm tall, 353 mm wide, 341 mm deep;
- Three chest plate options - with a normal “Police” logo, with a damaged logo, and a clean plate;
- You can 3D print Chappie’s gangster chains as one piece or separately;
- Moveable head;
- Moveable antennae and rotatable fan on the head;
- Moveable shoulder light and pauldrons;
- Articulated shoulder and elbow joints;
- You can 3D print the shoulder joints with or without the support rim;
- Articulated wrist joints;
- Multidirectional movement of the torso;
- Articulated hip, knee and ankle joints;
- You can 3D print knee belts that come adjusted for the standing pose, bend the straight belts to your liking or 3D print them using flexible filament;
- Some cables can be substituted with real-life cables or flexible wire;
- The assembly of the model requires pins that can be made out of short pieces of regular 1.75 mm filament or 3D printed using STL files #150-152;
- Tunnels throughout the robot's upper body are provided for you to introduce LED wiring and light up the eyes, shoulder and chest light; there's an opening hatch at the back to access the battery;
- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:
- Contains 160 parts;
- A printed model stands 472 mm tall, 353 mm wide, 341 mm deep;
- Three chest plate options - with a normal “Police” logo, with a damaged logo, and a clean plate;
- You can 3D print Chappie’s gangster chains as one piece or separately;
- Moveable head;
- Moveable antennae and rotatable fan on the head;
- Moveable shoulder light and pauldrons;
- Articulated shoulder and elbow joints;
- You can 3D print the shoulder joints with or without the support rim;
- Articulated wrist joints;
- Articulated hip, knee and ankle joints;
- Multidirectional movement of the torso;
- Fixing the model in your chosen pose and limited articulation are recommended to avoid wear-out of the joints;
- Careful assembly and some light sanding of the joints are recommended;
- You can 3D print knee belts that come adjusted for the standing pose or 3D print the straight belts using flexible material;
- Some cables can be substituted with real-life cables or flexible wire;
- The assembly of the model requires pins that can be 3D printed using STL files #150-152;
- Tunnels throughout the robot's upper body are provided for you to introduce LED wiring and light up the eyes, shoulder and chest light; there's an opening hatch at the back to access the battery;
- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

You can get the model of Chappie for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Chappie 3D Printing Model on Gambody YouTube channel.

Also, you may like MOOSE Mech 3D Printing Model, as well as other Fiction models.

 

_______
FAQ: 

Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

Below you can find printing recommendations for CuraSimplify3DSlic3r and PrusaSlicer software.

Cura printing recommendations:

These are basic settings that were tested in Cura 4.8.0 slicer. 

The test models were printed on Ultimaker 2, Creality Ender 3, Creality CR-10S Pro V2, Anycubic I3 Mega, Anycubic I3 MegaS 3D printers with PLA and PETG filaments.

Disclaimer: The following printing settings are a recommendation, not an obligation. The parameters can vary depending on the peculiarities of your 3D printer, the material you use and especially the particular assembly part at hand. Each part that any model comprises often needs preliminary review and you are free to tweak the settings the way you find suitable.

Note:
- You can scale up the model (downscaling is not recommended!);
- All connectors should be printed at 100% Infill;
- For all parts of locks (“ge_lock” in “Source files”) you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

Quality
Layer Height: 0.12 mm (you can also set Layer Height at 0.16 or 0.2mm for 0.4mm nozzles)
Initial Layer Height: 0.2 mm (carefully level the print bed and keep your Initial Layer Height the same as the main Layer Height)

Line Width: 0.4 mm
Wall Line Width: 0.4 mm
Outer Wall Line Width: 0.4 mm
Inner Wall(s) Line Width: 0.4 mm
Top/Bottom Line Width: 0.4 mm
Infill Line Width: 0.4 mm
Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm

Initial Layer Line Width: 100%

Shell 
Wall Thickness: 0.8 mm
Wall Line Count: 2

Outer Wall Wipe Distance: 0.3 mm
Top Surface Skin Layers: 0

Top/Bottom Thickness: 0.6 mm
Top Thickness: 0.6 mm
Top Layers: 5
Bottom Thickness: 0.6 mm
Bottom Layers: 5
Initial Bottom Layers: 5

Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Optimize Wall Printing Order: Check

Compensate Wall Overlaps: Check
Compensate Inner Wall Overlaps: Check

Minimum Wall Flow: 0%
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Hole horizontal expansion: 0

Z Seam Alignment: User Specified
Z Seam Position: Back
Z Seam X: Average length of your printer’s plate (e.g.”150” if your plate is 300mm on the X-axis)
Z Seam Y: A value higher than the length of your plate on the Y-axis (e.g. 700)

Seam Corner Preference: Hide Seam
Extra Skin Wall Count: 1
Skin Overlap Percentage: 10%
Skin Overlap 0.04 mm

Infill 
Infill Density: 20% (for all smaller parts and for all parts of connectors use 100% Infill)
Infill Pattern: Triangles
Connect Infill Lines: Check
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Line Multiplier: 1
Extra Infill Wall Count: 0

Infill Overlap Percentage: 10-20%
Infill Overlap: 0.04 mm

Skin Overlap Percentage: 5%
Skin Overlap: 0.02 mm

Infill Wipe Distance: 0 mm
Infill Layer Thickness: 0.24 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2

Skin Removal Width: 0.8 mm
Top Skin Removal Width: 0.8 mm
Bottom Skin Removal Width: 0.8 mm

Skin Expand Distance: 0.8
Top Skin Expand Distance: 0.8
Bottom Skin Expand Distance: 0.8

Maximum Skin Angle for Expansion: 90˚
Minimum Skin Width for Expansion: 0.0
Skin Edge Support Thickness: 0
Skin Edge Support Layers: 0

Material 
Initial Layer Flow: 100%
Printing Temperature: See your filament settings
Initial Printing Temperature: Your filament settings
Final Printing Temperature: Your filament settings
Build Plate Temperature: Your filament settings
Build Plate Temperature Initial Layer: Your filament settings + 5°
Flow: 100% (Important! If you face difficulty printing the model, you may need to adjust the Flow parameter. You may research the topic using the Internet or seek assistance at our Customer Support Team at support@gambody.com)

Speed 

You can increase the printing Speed by 20% when you print simple objects. For small/thin parts you need to decrease the Speed by 25% - 50%.

Print Speed: 50 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 25 mm/s
          Outer Wall Speed:25 mm/s
          Inner Wall Speed: 50 mm/s

Top/Bottom Speed: 25mm/s
Support Speed: 25 mm/s 
          Support Infill Speed: 45 mm/s
          Support Interface Speed: 25 mm/s
                Support Roof Speed: 25 mm/s
                Support Floor Speed: 25 mm/s

Travel Speed: 80 mm/s
Initial Layer Speed: 80 mm/s
Initial Layer Print Speed: 20 mm/s
Initial Layer Travel Speed: 80 mm/s

Skirt/Brim Speed: 20 mm/s
Z  Hop Speed: 5 mm/s
Number of Slower Layers: 2
Enable Acceleration Control: Check

When printing simple objects, you need to set all Acceleration parameters at 500 mm/s. For small/thin parts you need to decrease the Acceleration by 50% - 70%.

Travel 
Enable Retraction: Check
Retraction Distance: 4-8 mm, 1-3 mm for Direct Extruder (This is the most important retraction parameter. You can find your optimal value of Retraction Distance by printing any test object, e.g. bridges, towers etc.)

Retraction Speed: 25mm/s
Retraction Retract Speed: 25 mm/s
Retraction Prime Speed: 25 mm/s

Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 1.5 mm
Maximum Retraction Count: 100
Minimum Extrusion Distance Window: 6,5 - 10 mm
Limit Support Retractions: Check
Combing Mode: All
Max Comb Distance With No Retract: 30 mm
Retract Before Outer Wall: Check
Avoid Printed Parts When Travelling: Check
Avoid Supports When Travelling: Check
Travel Avoid Distance: 1 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm
Z Hop When Retracted: Check
Z Hop Height: 0,3 mm

Cooling 
Enable Print Cooling: Check
Fan Speed: 100%
Regular Fan Speed: 100%
Maximum Fan Speed: 100% 

Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.36 mm
Regular Fan Speed at Layer: 3 

Minimum Layer Time: 10 s
Minimum Speed: 10 mm/s

Support 
Generate Support: Check
Support Structure: Normal (you can try using Tree Support Structure if you have difficulty printing any particular assembly part)
Support Placement: Everywhere 
Support Overhang Angle: 60° (this parameter can range from 30° to 70° depending on the part at hand)
Support Pattern: Zig Zag
Support Wall Line Count: 1 (stronger support that might be more difficult to remove) 0 (less strong support but is easier to remove)

Support Density: 15%
Support Line Distance: 2.6667 mm
Initial layer support line distance: 2.667 mm

Support Z Distance: 0.12 mm
Support Top Distance: 0.12 mm
Support Bottom Distance: 0.12 mm

Support X/Y Distance: 0.8-1 mm
Support Distance Priority: Z overrides X/Y
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Stair Step Minimum Slope Angle: 10°
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.2 mm
Gradual Support Infill Steps: 0
Minimum Support Area: 2 mm

Enable Support Interface: Check (generates additional “pillow” on the support structure that leads to a more even surface, but can be difficult to remove in hard-to-reach areas)
Enable Support Roof: Check
Enable Support Floor: Check

Support Interface Thickness: 0.8 mm
Support Roof Thickness: 0.8 mm
Support Floor Thickness: 0.8 mm

Support Interface Resolution 0.2 mm
Support Interface Density: 50-100%
        Support Roof Density: 50-100%
Support Roof Line Distance: 0.8 mm
        Support Floor Density: 50-100%
Support Floor line Distance:  0.4mm

Support Interface Pattern: Grid 
Support Roof Pattern: Grid (this parameter should differ from Bottom Pattern Initial Layer in “Shell” section)
Support Floor Pattern: Grid

Minimum Support Interface Area: 10mm
Minimum Support Roof Area: 10 mm
Minimum Support Floor Area: 10 mm

Support Interface Horizontal Expansion: 0.0 mm
Support Roof Horizontal Expansion: 0.0 mm
Support Floor Horizontal Expansion: 0.0 mm

Fan Speed Override: Check
Supported Skin Fan Speed: 100%
Use Towers: Check
Tower Diameter: 4 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Skirt/Brim (For unsteady parts, and those parts that may come unstuck use “Brim”. For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
       Brim Line Count: 10
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Experimental
Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Extruder
Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Layer
Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Additions
Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Infill
Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Support
Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Temperature
Extruder 1 Temperature: 210
Heated Bed: 60

Cooling
Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Speeds
Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Other
Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

These basic 3D printing settings recommendations for beginners were tested in Slic3r 1.3.0 software. Test models were printed on Ultimaker 2, Creality Ender 3, Creality Cr-10S pro v2, Anycubic I3 Mega, Anycubic I3 MegaS, Anycubic Vyper with PLA and PetG filaments. 

Note:

- You can upscale your 3D printing models. Downscaling is not recommended - it can make smaller parts of the model unprintable, distort the model’s level of detail and result in assembly issues. 
- All connectors should be printed at 100% Infill.
- When printing Lock connectors, we recommend setting the “Brim width” parameter to 0 in the "Skirt and Brim" print settings. In that way, the Locks will be 3D printed with a Skirt only. 

Print Settings Tab
 
Layers and perimeters
Layer height:
Layer Height: 0.1-0.2 
First layer height: 0.2-0.3
Vertical shells:
Perimeters: 2-3
Spiral vase: OFF
Horizontal shells:
Solid layers: 8 (For 0.1 Layer Height) or 4 (For 0.2 Layer Height)
Quality (slow slicing)
Extra perimeters if needed: CHECK
Avoid crossing perimeters:  CHECK
Detect thin walls: -//-
Detect bridging perimeters:  CHECK
 
Advanced: 
Seam position: Aligned
External perimeters first: -//-
 
Infill
Fill Density: 10%
Fill Pattern: Rectilinear
Top Fill Pattern: Rectilinear
Bottom fill pattern: Rectilinear
 
Reducing printing time:
Combine infill every: 1
Only infill where needed: -//-
 
Advanced:
Fill gaps: CHECK
Solid Infill every: 0
Fill angle: 45
Solid Infill threshold area: 70
Bridging angle: 0
Only retract when crossing perimeters: CHECK
Infill before perimeters: -//-
 
Skirt and brim
Skirt
Loops (minimum): 3
Distance from Object: 5
Skirt Height: 1 ( for pla and petg)
Minimal Filament extrusion length: 50
 
Brim
Brim width: (5-8 mm is optional for small prints that have bad adhesion to the build plate)
 
Support material
Support Material:
Generate Support material: -//- (enable this parameter if your model requires supports)
Overhang threshold: 40-60
Enforce support for the first: 0
 
Raft:
Raft Layers: 0
Options for Support material and Raft:
Contact Z distance: 0.2
Pattern: Rectilinear 
Pattern spacing: 2.5
Pattern angle: 0
Interface Layers: 3
Interface pattern spacing: 0.2
Support on build plate only: -//-
Don’t support bridges: CHECK
 
Speed
 
Speed for print movies
(We recommend that you try printing with the parameters listed below and then adjust the print speed until the printing quality is optimal for you)
Perimeters: 20 mm/s
Small perimeters: 20 mm/s
External perimeters: 20 mm/s
Infill: 50 mm/s
Solid: 30 mm/s
Top solid :  20 mm/s
Gaps: 20 mm/s
Bridges: 20 mm/s
Support material: 50 mm/s
 
Speed for non print movies
Travel: 100 mm/s
 
Modifiers
First layer speed: 10 mm/s
 
Acceleration control (Settings for advanced users, change these parameters only if you have sufficient 3D printing expertise)
Perimeters: 400 mm/s2
Infill: 400 mm/s2
Bridge: 400 mm/s2
First layer: 300 mm/s2
Default: 400 mm/s2
 
Auto speed (advanced)
Max print speed: 100 mm/s
Max volumetric speed: 0 mm3/s
 
Multiple Extruders
These settings only work for 3D printers with multiple extruders (not recommended for beginners)
 
Advanced
Extrusion width 
You can try setting all parameters in this section, except the First layer, to values between 0.75% of your nozzle diameter and 1.25% of your nozzle diameter. Adjusting them will help you work out the optimal parameters for the best quality for your print. As for the First layer, you can set it to 150% of the diameter of your nozzle for better adhesion to the build plate (for a nozzle with a diameter of 0.4 mm, the First layer extrusion width can be from 0.3 mm to 0.5 mm)
 
Overlap
Infill/perimeters overlap: 25%
 
Flow
Bridge flow ratio: 0.7
 
Other
-//-
Output options
-//-
Notes
-//-
Shortcuts
-//-
 
Filament Settings Tab
 
Filament
Filament
Color: -//-
Diameter: 1.75
Extrusion multiplier: 1
Density: -//-
Cost: -//-
(You can set these parameters yourself if you need)
 
Cooling
Enable
Keep fan always on: CHECK
Enable auto cooling: -//-
 
Fan settings
Fan speed
Min: 100% (for PLA, PETG) or 30% (for ABS, SBS)
Max: -//-
Bridges fan speed: 100%
Disable fan for the first: 1
 
Cooling thresholds
Enable fan if layer print time is below: -//-
Slow down if layer print time is below: -//-
Min print Speed: -//-
 
Custom G-code
-//-
Notes
-//-
 
Printer Settings Tab
 
General 
Size and coordinates
Bed shape: your 3D printer’s bed size
Z offset: 0
Capabilities
Extruders: 1
Has heated bed: CHECK
Firmware
G-code flavor: RepRap (Marlin/Sprinter)
Advanced
Use relative E distances: CHECK
 
Custom G-code
Use your 3D printer’s standard G-code. If you don't have it, you may use the example below.
Start G-code
M104 S(First_layer_temperature) 
M140  S(First_layer_bed_temperature)
G28 S(Parking)
M109 S(waiting_for_warm-up_nozzle) 
M190  S(waiting_for_warm-up_bed)
End G-code
M104 s0 ;turn off nozzle
M140 s0 ;turn off bed
G91
G1 Z1 
G28 X0 Y0 ;park
M84 ;disable motors
M107 ;disable cooling
 
Extruder 1
Size
Nozzle diameter: 0.4 mm
Layer height limits
Min: 0.05
Max: 0.3
Position
Extruder offset: -//-
Retraction
Length: 5.5-6.5 mm (1mm for a direct extruder)
Lift Z: 0-0.3 mm
Speed: 30 - 40 mm/s
Extra length on restart: 0 mm
Minimum travel after retraction: 2 mm
Retract on layer change: -//- (you can try to enable this parameter)
Wipe while retracting: -//-  (you can try to enable this parameter)
 

PrusaSlicer printing recommendations:

 
These basic 3D printing settings recommendations for beginners were tested in PrusaSlicer 2.3.1. Test models were printed on Ultimaker 2, Creality Ender 3, Creality Cr-10S pro v2, Anycubic I3 Mega, Anycubic I3 MegaS, Anycubic Vyper with PLA and PETG filaments.
 
Note:
- You can upscale your 3D printing models. Downscaling is not recommended - it can make smaller parts of the model unprintable, distort the model’s level of detail and result in assembly issues.
- All connectors should be printed at 100% Infill.
- When printing Lock connectors, we recommend setting the “Brim width” parameter to 0 in the "Skirt and Brim" print settings. In that way, the Locks will be 3D printed with a Skirt only. 
 
In order to see all the parameters listed below, you need to enable the Expert mode in the PrusaSlicer’s settings.
 
Print Settings Tab
 
Layers and perimeters
Layer height:
Layer Height: 0.1-0.2
First layer height: 0.2-0.3
Vertical shells:
Perimeters: 2-3
Spiral vase: OFF
Horizontal shells:
Solid layers: 8 (for 0.1 Layer Height) or 4 (for 0.2 Layer Height)
Minimum shell thickness: 0.8
Quality (slower slicing)
Extra perimeters if needed: CHECK
Ensure vertical shell thickness: -//-
Avoid crossing perimeters:  CHECK
Detect thin walls: -//-
Detect bridging perimeters:  CHECK
Advanced: 
Seam position: Aligned
External perimeters first: -//-
 
Infill
Infill
Fill Density: 10%
Fill Pattern: Rectilinear
Top Fill Pattern: Monotonic
Bottom fill pattern: Monotonic
Reducing printing time:
Combine infill every: 1
Only infill where needed: -//-
Advanced:
Solid Infill every: 0
Fill angle: 45
Solid Infill threshold area: 70
Bridging angle: 0
Only retract when crossing perimeters: CHECK
Infill before perimeters: -//-
 
Skirt and brim
Skirt
Loops (minimum): 3
Distance from Object: 5
Skirt Height: 1 (for PLA and PETG)
Draft Shield: -//-
Minimal filament extrusion length: 50
Brim
Brim width: (5-8 mm is optional for small prints that have bad adhesion to the build plate)
 
Support material
Support Material:
Generate Support material: -//- (enable this parameter if your model requires supports)
Auto generated supports: CHECK
Overhang threshold: 40-60
Enforce support for the first: 0
Raft:
Raft Layers: 0
Options for Support material and Raft:
Contact Z distance: 0.2
Pattern: Rectilinear 
With sheath around the support: CHECK
Pattern spacing: 2.5
Pattern angle: 0
Interface Layers: 3
Interface pattern spacing: 0.2
Interface loops: -//-
Support on build plate only: -//-
XY separation between an object and its support: 50%
Don’t support bridges: CHECK
Synchronize with object layers: -//-
 
Speed
Speed for print moves
(We recommend that you try printing with the parameters listed below and then adjust the print speed until the printing quality is optimal for you)
Perimeters: 20 mm/s
Small perimeters: 20 mm/s
External perimeters: 20 mm/s
Infill: 50 mm/s
Solid infill: 30 mm/s
Top solid infill:  20 mm/s
Support material: 50 mm/s
Support material interface: 20 mm/s
Bridges: 20 mm/s
Gap fill: 20 mm/s
Ironing: 15 mm/s
 
Speed for non-print moves
Travel: 100 mm/s
 
Modifiers
First layer speed: 10 mm/s
 
Acceleration control (Settings for advanced users, change these parameters only if you have sufficient 3D printing expertise)
Perimeters: 400 mm/s2
Infill: 400 mm/s2
Bridge: 400 mm/s2
First layer: 400 mm/s2
Default: 400 mm/s2
 
Auto speed (advanced)
Max print speed: 100 mm/s
Max volumetric speed: 0 mm3/s
 
Multiple Extruders
These settings only work for 3D printers with multiple extruders (not recommended for beginners)
 
Advanced
Extrusion width 
 
You can try setting all parameters in this section, except the First layer, to values between 0.75% of your nozzle diameter and 1.25% of your nozzle diameter. Adjusting them will help you work out the optimal parameters for the best quality for your print. As for the First layer, you can set it to 150% of the diameter of your nozzle for better adhesion to the build plate (for a nozzle with a diameter of 0.4 mm, the First layer extrusion width can be from 0.3 mm to 0.5 mm)
 
Overlap
Infill/perimeter overlap: 25%
 
Flow
Bridge flow ratio: 0.7
 
Slicing
-//-
Other
Clip multi-part objects: CHECK
Output options
-//-
Notes
-//-
Dependencies
-//-
 
Filament Settings Tab
Filament
Filament
Color: -//-
Diameter: 1.75
Extrusion multiplier: 1
Density: -//-
Cost: -//-
Spool weight: -//-
(You can set these parameters yourself if you need)
Temperature
Сheck your filament manufacturer's temperature recommendations on the spool.
 
Cooling
Enable
Keep fan always on: CHECK
Enable auto cooling: -//-
Fan settings
Fan speed
Min: 100% (for PLA, PETG) or 30% (for ABS, SBS)
Max: -//-
Bridges fan speed: 100%
Disable fan for the first: 1
Full fan speed at layer: 3-4
Cooling thresholds
Enable fan if layer print time is below: -//-
Slow down if layer print time is below: -//-
Min print speed: -//-
 
Advanced
Print speed override
Max volumetric speed:
PLA: 14 MM3/S
ABS:  10 MM3/S
PETG:  14 MM3/S
HIPS: 10 MM3/S
(If you use the Volcano extruder for your printer, all parameters need to be increased x2)
 
Filament Overrides
-//-
Custom G-code
-//-
Notes
-//-
Dependencies
-//-
 
Printer Settings Tab
 
General 
Size and coordinates
Bed shape: your 3D printer’s bed size
Max print height: your 3D printer’s height
Z offset: 0
Capabilities
Extruders: 1
Single Extruder Multi Material: -//-
Firmware
G-code flavor: RepRap/Sprinter
G-code thumbnails: -//-
Supports stealth mode: -//-
Supports remaining times: -//-
Advanced
Use relative E distances: CHECK
Use firmware retraction: -//- (needs to be enabled in the firmware of your printer)
Use volumetric E: -//-
Enable variable layer height feature: CHECK
 
Custom G-code
Use your 3D printer’s standard G-code. If you don't have it, you may use the example below.
Start G-code
M104 S(First_layer_temperature) 
M140  S(First_layer_bed_temperature)
G28 S(Parking)
M109 S(waiting_for_warm-up_nozzle) 
M190  S(waiting_for_warm-up_bed)
End G-code
M104 s0 ;turn off nozzle
M140 s0 ;turn off bed
G91
G1 Z1 
G28 X0 Y0 ;park
M84 ;disable motors
M107 ;disable cooling
 
Extruder 1
Size
Nozzle diameter: 0.4 mm
Layer height limits
Min: 0.05
Max: 0.3
Position
Extruder offset: -//-
Retraction
Length: 5.5-6.5 mm (1 mm for a direct extruder)
Lift Z: 0-0.3 mm
Retraction Speed: 30 - 40 mm/s
Deretraction Speed: 0 mm/s
Extra length on restart: 0 mm
Minimum travel after retraction: 2 mm
Retract on layer change: -//- (you can try to enable this parameter)
Wipe while retracting: -//-  (you can try to enable this parameter)
Retract amount before wipe:
Notes
-//-
Dependencies
-//-

Comments

comments powered by Disqus

Similar items

Browse more newly listed 3D printings