Make pre-order

cm: 33 w x 54.7 d x 40.8 h
in: 12.992 w x 21.535 d x 16.063 h
BUY FOR  $24.99

Source Files




Printing Details

This 3D Miniature consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Version 1 and Version 2 are the files for Godzilla Hybrid 3D Miniature optimized for 3D printing, the preview pictures of which you see above.

It is recommended:

  • to print Version 1 STL files on FDM/FFF 3D printers;
  • to print Version 2 STL files on DLP/SLA/SLS 3D printers.
File Name File Size Time / Filament
7.34 MiB 37 h 13 min
22 m
6.35 MiB 36 h 57 min
22 m
6.52 MiB 40 h 24 min
24 m
8.21 MiB 38 h 25 min
22 m
5_Ge_lock_10S (x31).STL
0.02 MiB 4 min
<1 m
12.11 MiB 51 h 1 min
34 m
24.27 MiB 130 h 45 min
89 m
11.90 MiB 51 h 54 min
35 m
6.26 MiB 11 h 37 min
8 m
15.54 MiB 107 h 45 min
70 m
6.17 MiB 11 h 35 min
7 m
11.92 MiB 27 h 29 min
19 m
7.84 MiB 79 h 46 min
50 m
7.53 MiB 22 h 27 min
14 m
12_head_v2_FDM(repaired). stl
29.97 MiB 26 h 18 min
17 m
12_head_jaw_2_FDM(repaire d).stl
3.71 MiB 20 min
<1 m
12_head_jaw_1_FDM(repaire d).stl
17.96 MiB 1 h 37 min
1 m


In the new era, Godzilla collided with an incredible adversary. A huge alien creature that was in the ocean. It wakes up and jumps on the roof of the office skyscraper using its electromagnetic "tentacles" to enter into the super-computer and begins to read all the data. It turns out that the stranger wants to change the atmosphere of the Earth, after which the new era of the Millennium will begin. Godzilla attracts his ability to regenerate. Soon Godzilla appears from the sea and heads towards her enemy. The alien first deviates from Godzilla's atomic beam, but then he gets Godzilla's cell samples and creates a hunchbacked monster similar to him with long crooked paws and a small head - Orga. Godzilla destroys the flying alien by the atomic beam and fights against Orga. With each close contact, the new monster becomes more and more like Godzilla. Finally, Orga reveals a huge mouth and tries to swallow Godzilla acquiring his features, but Godzilla shoots by his atomic beam in time, tearing the enemy to pieces. After this, the lizard destroys the building with a paw and then turns around and goes on to continue destroying the city. Everyone has to admit that nothing can stop this monster.


The model is saved in STL files, a format supported by most 3D printers

FDM version features:
- Contain 14 parts;
- Made with Locks for better fixing. One part of Lock (5_Ge_lock_10S (x31)) you need to print 31 times.
- Made with platform that divided on 4 parts for small buildplates;
- All parts are divided in such way that you will print them with the smallest amount of supports.

SLS/SLA version features:
- Same as FDM but smaller, made as 3 parts, and contain 2 variants (with divided platform).

All STL files for 3D printing have been checked in Netfabb and no errors were shown.

Note: Before starting 3D printing the model, read the Printing Details for CURA 3.2.1. Software.

There are 14 parts for FFF/FDM version and 3 parts for SLS/SLA version.

Scale: His tall in life is 91000 mm. Model made as 1/200 scale in FDM version and 1/400 in SLS/SLA version.

FDM version dimensions:
After being printed will stand - 408 mm tall, 330 mm wide, 547 mm deep;

SLS/SLA version dimensions:
After being printed will stand - 204 mm tall, 165 mm wide, 274 mm deep;
- Has few details, to keep printing costs down.


- STL files of Godzilla Hybrid 3D Miniature for 3D printing which consist of 17 parts;
- 2 versions of files for this model for FFF/FDM and SLS/SLA (contain 2 variants);
- Made with platform;
- Model fixed by the Locks;
- High-poly detailed miniature of Godzilla Hybrid;
- Detailed settings that we provide for Cura 3.2.1. for the best print;
- Full technical support from the Gambody Support Team.

Watch the tutorial video on how to assemble Godzilla Hybrid 3D Printing Miniature at Gambody YouTube channel.

You can get Model of Godzilla Hybrid for 3D Printing right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Also, you may like other Villains 3D Printing Miniatures.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine

This model was tested in Cura 3.2.1 and printed on an Ultimaker 2 in PLA material.

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

To avoid printing problems, we recommend the following settings:

Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Print Speed: 45 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
Travel Speed: 120 mm/s
Initial Layer Speed: 30 mm/s
  Initial Layer Print Speed: 30 mm/s
  Initial Layer Travel Speed: 60 mm/s
Skirt/Brim Speed: 30 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 1.3333 mm
Support Z Distance: 0.3 mm
    Support Top Distance: 0.3 mm
    Support Bottom Distance: 0.3 mm
Support X/Y Distance: 0.7 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.2 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 18 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.


comments powered by Disqus
Other author's 3D printings


Kaiju, Monster, Millennium, Assembly, Godzilla

Similar items

Browse more newly listed 3D printings