Make pre-order

Destoroyah 3D Printing Figurine | Assembly

big
cm: 65.9 w x 61.6 d x 65.9 h
in: 25.945 w x 24.252 d x 25.945 h

Source Files

|

Description

|

Printing Details

This 3D figurine of Destoroyah Kaiju consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

WHAT WILL YOU GET AFTER PURCHASE?

4 versions of Destoroyah STL files for FFF/FDMDLP/SLADLP/SLA Eco, and SLS - files for each version are available for download after the purchase

- STL files of high-poly Kaiju Destoroyah for 3D printing consist of 137 files
Sizes:
FFF/FDM: 659 mm tall, 847 mm wide, 616 mm deep
DLP/SLA/SLS: 330 mm tall, 424 mm wide, 308 mm deep

Assembly Manual for FFF/FDM 1.0 and DLP/SLA 1.0 versions in PDF format
- Detailed settings that we provide as a recommendation for Cura, Simplify3D, Slic3r and PrusaSlicer for the best print
- Full technical support from the Gambody Support Team

Detailed information about this 3D printing figurine is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
1_head_FDM(repaired).stl
56.42 MiB 40 h 12 min
25 m
94 x 131 x 123 Download
2_horn_FDM(repaired).stl
14.60 MiB 46 min
<1 m
18 x 26 x 56 Download
3_ear_R_FDM(repaired).stl
18.70 MiB 7 h 22 min
4 m
51 x 110 x 69 Download
4_ear_L_FDM(repaired).stl
19.17 MiB 6 h 52 min
4 m
105 x 50 x 68 Download
5_tooth_1_R_FDM(repaired) .stl
1.45 MiB 3 min
<1 m
5 x 5 x 11 Download
6_tooth_2_R_FDM(repaired) .stl
3.97 MiB 8 min
<1 m
6 x 10 x 17 Download
7_tooth_3_R_FDM(repaired) .stl
3.67 MiB 6 min
<1 m
6 x 9 x 13 Download
8_tooth_1_L_FDM(repaired) .stl
1.63 MiB 3 min
<1 m
6 x 6 x 11 Download
9_tooth_2_L_FDM(repaired) .stl
4.05 MiB 8 min
<1 m
11 x 7 x 16 Download
10_tooth_3_L_FDM(repaired ).stl
3.56 MiB 5 min
<1 m
9 x 7 x 12 Download
11_chest_FDM(repaired).st l
46.76 MiB 123 h 59 min
78 m
Download
12_body_FDM(repaired).stl
38.11 MiB 108 h 11 min
66 m
Download
13_tail_1_FDM(repaired).s tl
25.41 MiB 52 h 54 min
31 m
Download
14_tail_2_FDM(repaired).s tl
22.65 MiB 51 h 36 min
33 m
118 x 134 x 117 Download
15_tail_3_FDM(repaired).s tl
22.33 MiB 38 h 26 min
24 m
107 x 102 x 120 Download
16_tail_4_FDM(repaired).s tl
19.91 MiB 21 h 11 min
12 m
80 x 74 x 120 Download
17_tail_5_FDM(repaired).s tl
24.16 MiB 13 h 57 min
8 m
60 x 94 x 91 Download
18_tail_6_FDM(repaired).s tl
22.18 MiB 8 h 39 min
6 m
80 x 45 x 79 Download
19_tail_7_FDM(repaired).s tl
20.16 MiB 5 h 51 min
3 m
44 x 60 x 98 Download
20_tail_8_FDM(repaired).s tl
22.48 MiB 8 h 47 min
6 m
52 x 80 x 92 Download
21_arm_R_FDM(repaired).st l
31.95 MiB 21 h 9 min
15 m
Download
22_arm_L_FDM(repaired).st l
37.63 MiB 19 h 7 min
13 m
Download
23_leg_R_1_FDM(repaired). stl
19.65 MiB 48 h 48 min
30 m
Download
24_leg_R_2_FDM(repaired). stl
22.44 MiB 55 h 22 min
35 m
Download
25_spike_1_leg_R_FDM(repa ired).stl
5.19 MiB 26 min
<1 m
27 x 19 x 28 Download
26_spike_2_leg_R_FDM(repa ired).stl
4.41 MiB 18 min
<1 m
15 x 18 x 22 Download
27_spike_3_leg_R_FDM(repa ired).stl
7.70 MiB 23 min
<1 m
21 x 12 x 29 Download
28_spike_4_leg_R_FDM(repa ired).stl
5.13 MiB 23 min
<1 m
22 x 13 x 27 Download
29_spike_5_leg_R_FDM(repa ired).stl
3.43 MiB 18 min
<1 m
Download
30_spike_6_leg_R_FDM(repa ired).stl
3.80 MiB 22 min
<1 m
Download
31_leg_L_1_FDM(repaired). stl
24.41 MiB 51 h 15 min
31 m
Download
32_leg_L_2_FDM(repaired). stl
23.22 MiB 54 h 55 min
35 m
Download
33_spike_1_leg_L_FDM(repa ired).stl
2.21 MiB 20 min
<1 m
15 x 19 x 25 Download
34_spike_2_leg_L_FDM(repa ired).stl
1.81 MiB 14 min
<1 m
14 x 15 x 17 Download
35_spike_3_leg_L_FDM(repa ired).stl
3.63 MiB 21 min
<1 m
17 x 12 x 25 Download
36_spike_4_leg_L_FDM(repa ired).stl
4.76 MiB 19 min
<1 m
19 x 8 x 26 Download
37_spike_5_leg_L_FDM(repa ired).stl
3.02 MiB 17 min
<1 m
13 x 18 x 21 Download
38_spike_6_leg_L_FDM(repa ired).stl
2.82 MiB 27 min
<1 m
30 x 20 x 29 Download
39_spike_1_R_FDM(repaired ).stl
9.28 MiB 3 h 44 min
2 m
47 x 36 x 94 Download
40_spike_2_R_FDM(repaired ).stl
9.66 MiB 2 h 37 min
1 m
47 x 55 x 54 Download
41_spike_1_L_FDM(repaired ).stl
10.00 MiB 4 h 20 min
3 m
49 x 45 x 95 Download
42_spike_2_L_FDM(repaired ).stl
9.95 MiB 2 h 41 min
1 m
42 x 54 x 65 Download
43_wing_small_R_1_FDM(rep aired).stl
14.73 MiB 4 h 36 min
3 m
67 x 27 x 98 Download
44_wing_small_R_2_FDM(rep aired).stl
13.53 MiB 9 h 53 min
7 m
106 x 67 x 126 Download
45_wing_small_L_1_FDM(rep aired).stl
14.95 MiB 8 h 5 min
5 m
61 x 66 x 108 Download
46_wing_small_L_2_FDM(rep aired).stl
13.94 MiB 6 h 6 min
3 m
102 x 36 x 132 Download
47_wing_1_R_FDM(repaired) .stl
16.50 MiB 25 h 48 min
16 m
147 x 151 x 116 Download
48_wing_2_R_FDM(repaired) .stl
15.53 MiB 14 h 1 min
8 m
151 x 79 x 110 Download
49_wing_3_R_FDM(repaired) .stl
16.80 MiB 15 h 5 min
10 m
81 x 50 x 121 Download
50_wing_4_R_FDM(repaired) .stl
19.44 MiB 12 h 8 min
6 m
144 x 85 x 135 Download
51_wing_5_R_FDM(repaired) .stl
15.26 MiB 14 h 11 min
10 m
125 x 48 x 118 Download
52_wing_6_R_FDM(repaired) .stl
15.38 MiB 9 h 39 min
5 m
100 x 120 x 177 Download
53_wing_1_L_FDM(repaired) .stl
15.56 MiB 19 h 9 min
12 m
101 x 57 x 176 Download
54_wing_2_L_FDM(repaired) .stl
19.00 MiB 14 h 53 min
9 m
142 x 78 x 125 Download
55_wing_3_L_FDM(repaired) .stl
16.60 MiB 18 h 54 min
14 m
99 x 86 x 122 Download
56_wing_4_L_FDM(repaired) .stl
20.22 MiB 8 h 43 min
5 m
Download
57_wing_5_L_FDM(repaired) .stl
16.92 MiB 15 h 29 min
10 m
44 x 127 x 135 Download
58_wing_6_L_FDM(repaired) .stl
14.02 MiB 13 h 54 min
8 m
116 x 120 x 175 Download
59_platform_1_FDM(repaire d).stl
20.87 MiB 19 h 14 min
11 m
161 x 98 x 34 Download
60_platform_2_FDM(repaire d).stl
19.14 MiB 43 h 36 min
25 m
188 x 189 x 52 Download
61_platform_3_FDM(repaire d).stl
19.35 MiB 19 h 11 min
11 m
98 x 163 x 37 Download
62_platform_4_FDM(repaire d).stl
21.61 MiB 46 h 31 min
27 m
187 x 187 x 69 Download
63_platform_5_FDM(repaire d).stl
19.54 MiB 48 h 56 min
28 m
213 x 214 x 36 Download
64_platform_6_FDM(repaire d).stl
20.23 MiB 42 h 32 min
24 m
187 x 188 x 48 Download
65_platform_7_FDM(repaire d).stl
19.59 MiB 19 h 31 min
11 m
97 x 162 x 38 Download
66_platform_8_FDM(repaire d).stl
20.05 MiB 41 h 36 min
24 m
188 x 188 x 49 Download
67_platform_9_FDM(repaire d).stl
19.93 MiB 18 h 57 min
11 m
161 x 97 x 34 Download
68_ge_lock_7S(x1)_FDM(rep aired).stl
0.02 MiB 4 min
<1 m
7 x 18 x 2 Download
69_ge_lock_10H(x89)_FDM(r epaired).stl
0.03 MiB 4 min
<1 m
18 x 10 x 2 Download
Keychain (repaired).stl
0.35 MiB 23 min
<1 m
30 x 30 x 2 Download
Tag (repaired).stl
1.70 MiB 1 h 18 min
1 m
150 x 18 x 5 Download

ABOUT THIS 3D FIGURINE

Get ready for the final battle of the titans! One of the most fierce and a truly evil enemies of Heisei Godzilla has emerged - it is Destoroyah in his final form. Just like a demon it resembles, Destoroyah seeks to wreak havoc on his path and takes pleasure in the suffering of his victims. Only you will be able to stop him!

Destoroyah figurine for 3D printing is a remarkable piece for your Kaiju collection - it perfectly captures the last evolution stage of the terrifying monster and his merciless spirit. The layered exoskeleton structure,, four bat-like wings, large curved crests crowning his head, and a long tail with a pincer at the end are brought out by the highly detailed sculpt. What a terrifying beauty he is!

ADAPTATION FOR 3D PRINTING

Destoroyah for 3D printing is a static assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 48 hours. The figurine's anatomy and proportions were thoroughly reviewed during the moderation process for the kaiju to look harmonically in the intended pose.

The model’s cutting was chosen by our team to ensure the cleanest 3D printed result possible and some of the parts were hollowed out for you to save resin in the Eco version. In order to conceal the places where the assembly parts of the models are connected, the figurine was cut along the contour of Destoroyah's body. The monster's head, horns, wings, spikes, arms, legs, etc. are provided as separate assembly parts.

All assembly parts of the FFF/FDM versions come in STL files in recommended positions that were worked out in order to ensure the smoothness of the details’ surfaces after printing and so that the 3D printing beginners won't face difficulties when placing the parts on a build plate.

The figurine is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from the height of Destoroyah which is 120 000 mm. The 3D printing figurine's chosen scales are 1:250 for the FFF/FDM version and 1:500 for the DLP/SLA/SLS versions.

VERSIONS' SPECIFICATIONS

FFF/FDM 1.0 version features:
- Contains 69 parts;
- A printed model is 659 mm tall, 847 mm wide, 616 mm deep;
- The assembly kit includes locks 68_ge_lock_7S(x1) and 69_ge_lock_10H(x89) to assemble the figurine and the platform securely without glue, then number of required printed copies is written in parentheses;
- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:
- Contains 33 parts;
- A printed model is 330 mm tall, 424 mm wide, 308 mm deep;
- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

DLP/SLA Eco 1.0 version features:
- Contains 33 parts;
- A printed model is 330 mm tall, 424 mm wide, 308 mm deep;
- Some parts are manually hollowed out to save resin.

SLS 1.0 version features:
- A printed model is 330 mm tall, 424 mm wide, 308 mm deep;
- Contains 2 parts - a solid Destoroyah figurine and the platform.

You can get the Destoroyah figurine for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Destoroyah 3D Printing Figurine on Gambody YouTube channel.

Also, you may like other Kaiju models for 3D printing.

_______
FAQ: 

Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

Below you can find printing recommendations for CuraSimplify3DSlic3r and PrusaSlicer software.

Cura printing recommendations:

These are basic settings that were tested in Cura 4.8.0 slicer. 

The test models were printed on Ultimaker 2, Creality Ender 3, Creality CR-10S Pro V2, Anycubic I3 Mega, Anycubic I3 MegaS 3D printers with PLA and PETG filaments.

Disclaimer: The following printing settings are a recommendation, not an obligation. The parameters can vary depending on the peculiarities of your 3D printer, the material you use and especially the particular assembly part at hand. Each part that any model comprises often needs preliminary review and you are free to tweak the settings the way you find suitable.

Note:
- You can scale up the model (downscaling is not recommended!);
- All connectors should be printed at 100% Infill;
- For all parts of locks (“ge_lock” in “Source files”) you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

Quality
Layer Height: 0.12 mm (you can also set Layer Height at 0.16 or 0.2mm for 0.4mm nozzles)
Initial Layer Height: 0.2 mm (carefully level the print bed and keep your Initial Layer Height the same as the main Layer Height)

Line Width: 0.4 mm
Wall Line Width: 0.4 mm
Outer Wall Line Width: 0.4 mm
Inner Wall(s) Line Width: 0.4 mm
Top/Bottom Line Width: 0.4 mm
Infill Line Width: 0.4 mm
Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm

Initial Layer Line Width: 100%

Shell 
Wall Thickness: 0.8 mm
Wall Line Count: 2

Outer Wall Wipe Distance: 0.3 mm
Top Surface Skin Layers: 0

Top/Bottom Thickness: 0.6 mm
Top Thickness: 0.6 mm
Top Layers: 5
Bottom Thickness: 0.6 mm
Bottom Layers: 5
Initial Bottom Layers: 5

Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Optimize Wall Printing Order: Check

Compensate Wall Overlaps: Check
Compensate Inner Wall Overlaps: Check

Minimum Wall Flow: 0%
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Hole horizontal expansion: 0

Z Seam Alignment: User Specified
Z Seam Position: Back
Z Seam X: Average length of your printer’s plate (e.g.”150” if your plate is 300mm on the X-axis)
Z Seam Y: A value higher than the length of your plate on the Y-axis (e.g. 700)

Seam Corner Preference: Hide Seam
Extra Skin Wall Count: 1
Skin Overlap Percentage: 10%
Skin Overlap 0.04 mm

Infill 
Infill Density: 20% (for all smaller parts and for all parts of connectors use 100% Infill)
Infill Pattern: Triangles
Connect Infill Lines: Check
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Line Multiplier: 1
Extra Infill Wall Count: 0

Infill Overlap Percentage: 10-20%
Infill Overlap: 0.04 mm

Skin Overlap Percentage: 5%
Skin Overlap: 0.02 mm

Infill Wipe Distance: 0 mm
Infill Layer Thickness: 0.24 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2

Skin Removal Width: 0.8 mm
Top Skin Removal Width: 0.8 mm
Bottom Skin Removal Width: 0.8 mm

Skin Expand Distance: 0.8
Top Skin Expand Distance: 0.8
Bottom Skin Expand Distance: 0.8

Maximum Skin Angle for Expansion: 90˚
Minimum Skin Width for Expansion: 0.0
Skin Edge Support Thickness: 0
Skin Edge Support Layers: 0

Material 
Initial Layer Flow: 100%
Printing Temperature: See your filament settings
Initial Printing Temperature: Your filament settings
Final Printing Temperature: Your filament settings
Build Plate Temperature: Your filament settings
Build Plate Temperature Initial Layer: Your filament settings + 5°
Flow: 100% (Important! If you face difficulty printing the model, you may need to adjust the Flow parameter. You may research the topic using the Internet or seek assistance at our Customer Support Team at support@gambody.com)

Speed 

You can increase the printing Speed by 20% when you print simple objects. For small/thin parts you need to decrease the Speed by 25% - 50%.

Print Speed: 50 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 25 mm/s
          Outer Wall Speed:25 mm/s
          Inner Wall Speed: 50 mm/s

Top/Bottom Speed: 25mm/s
Support Speed: 25 mm/s 
          Support Infill Speed: 45 mm/s
          Support Interface Speed: 25 mm/s
                Support Roof Speed: 25 mm/s
                Support Floor Speed: 25 mm/s

Travel Speed: 80 mm/s
Initial Layer Speed: 80 mm/s
Initial Layer Print Speed: 20 mm/s
Initial Layer Travel Speed: 80 mm/s

Skirt/Brim Speed: 20 mm/s
Z  Hop Speed: 5 mm/s
Number of Slower Layers: 2
Enable Acceleration Control: Check

When printing simple objects, you need to set all Acceleration parameters at 500 mm/s. For small/thin parts you need to decrease the Acceleration by 50% - 70%.

Travel 
Enable Retraction: Check
Retraction Distance: 4-8 mm, 1-3 mm for Direct Extruder (This is the most important retraction parameter. You can find your optimal value of Retraction Distance by printing any test object, e.g. bridges, towers etc.)

Retraction Speed: 25mm/s
Retraction Retract Speed: 25 mm/s
Retraction Prime Speed: 25 mm/s

Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 1.5 mm
Maximum Retraction Count: 100
Minimum Extrusion Distance Window: 6,5 - 10 mm
Limit Support Retractions: Check
Combing Mode: All
Max Comb Distance With No Retract: 30 mm
Retract Before Outer Wall: Check
Avoid Printed Parts When Travelling: Check
Avoid Supports When Travelling: Check
Travel Avoid Distance: 1 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm
Z Hop When Retracted: Check
Z Hop Height: 0,3 mm

Cooling 
Enable Print Cooling: Check
Fan Speed: 100%
Regular Fan Speed: 100%
Maximum Fan Speed: 100% 

Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.36 mm
Regular Fan Speed at Layer: 3 

Minimum Layer Time: 10 s
Minimum Speed: 10 mm/s

Support 
Generate Support: Check
Support Structure: Normal (you can try using Tree Support Structure if you have difficulty printing any particular assembly part)
Support Placement: Everywhere 
Support Overhang Angle: 60° (this parameter can range from 30° to 70° depending on the part at hand)
Support Pattern: Zig Zag
Support Wall Line Count: 1 (stronger support that might be more difficult to remove) 0 (less strong support but is easier to remove)

Support Density: 15%
Support Line Distance: 2.6667 mm
Initial layer support line distance: 2.667 mm

Support Z Distance: 0.12 mm
Support Top Distance: 0.12 mm
Support Bottom Distance: 0.12 mm

Support X/Y Distance: 0.8-1 mm
Support Distance Priority: Z overrides X/Y
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Stair Step Minimum Slope Angle: 10°
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.2 mm
Gradual Support Infill Steps: 0
Minimum Support Area: 2 mm

Enable Support Interface: Check (generates additional “pillow” on the support structure that leads to a more even surface, but can be difficult to remove in hard-to-reach areas)
Enable Support Roof: Check
Enable Support Floor: Check

Support Interface Thickness: 0.8 mm
Support Roof Thickness: 0.8 mm
Support Floor Thickness: 0.8 mm

Support Interface Resolution 0.2 mm
Support Interface Density: 50-100%
        Support Roof Density: 50-100%
Support Roof Line Distance: 0.8 mm
        Support Floor Density: 50-100%
Support Floor line Distance:  0.4mm

Support Interface Pattern: Grid 
Support Roof Pattern: Grid (this parameter should differ from Bottom Pattern Initial Layer in “Shell” section)
Support Floor Pattern: Grid

Minimum Support Interface Area: 10mm
Minimum Support Roof Area: 10 mm
Minimum Support Floor Area: 10 mm

Support Interface Horizontal Expansion: 0.0 mm
Support Roof Horizontal Expansion: 0.0 mm
Support Floor Horizontal Expansion: 0.0 mm

Fan Speed Override: Check
Supported Skin Fan Speed: 100%
Use Towers: Check
Tower Diameter: 4 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Skirt/Brim (For unsteady parts, and those parts that may come unstuck use “Brim”. For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
       Brim Line Count: 10
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Experimental
Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Extruder
Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Layer
Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Additions
Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Infill
Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Support
Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Temperature
Extruder 1 Temperature: 210
Heated Bed: 60

Cooling
Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Speeds
Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Other
Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

These basic 3D printing settings recommendations for beginners were tested in Slic3r 1.3.0 software. Test models were printed on Ultimaker 2, Creality Ender 3, Creality Cr-10S pro v2, Anycubic I3 Mega, Anycubic I3 MegaS, Anycubic Vyper with PLA and PetG filaments. 

Note:

- You can upscale your 3D printing models. Downscaling is not recommended - it can make smaller parts of the model unprintable, distort the model’s level of detail and result in assembly issues. 
- All connectors should be printed at 100% Infill.
- When printing Lock connectors, we recommend setting the “Brim width” parameter to 0 in the "Skirt and Brim" print settings. In that way, the Locks will be 3D printed with a Skirt only. 

Print Settings Tab
 
Layers and perimeters
Layer height:
Layer Height: 0.1-0.2 
First layer height: 0.2-0.3
Vertical shells:
Perimeters: 2-3
Spiral vase: OFF
Horizontal shells:
Solid layers: 8 (For 0.1 Layer Height) or 4 (For 0.2 Layer Height)
Quality (slow slicing)
Extra perimeters if needed: CHECK
Avoid crossing perimeters:  CHECK
Detect thin walls: -//-
Detect bridging perimeters:  CHECK
 
Advanced: 
Seam position: Aligned
External perimeters first: -//-
 
Infill
Fill Density: 10%
Fill Pattern: Rectilinear
Top Fill Pattern: Rectilinear
Bottom fill pattern: Rectilinear
 
Reducing printing time:
Combine infill every: 1
Only infill where needed: -//-
 
Advanced:
Fill gaps: CHECK
Solid Infill every: 0
Fill angle: 45
Solid Infill threshold area: 70
Bridging angle: 0
Only retract when crossing perimeters: CHECK
Infill before perimeters: -//-
 
Skirt and brim
Skirt
Loops (minimum): 3
Distance from Object: 5
Skirt Height: 1 ( for pla and petg)
Minimal Filament extrusion length: 50
 
Brim
Brim width: (5-8 mm is optional for small prints that have bad adhesion to the build plate)
 
Support material
Support Material:
Generate Support material: -//- (enable this parameter if your model requires supports)
Overhang threshold: 40-60
Enforce support for the first: 0
 
Raft:
Raft Layers: 0
Options for Support material and Raft:
Contact Z distance: 0.2
Pattern: Rectilinear 
Pattern spacing: 2.5
Pattern angle: 0
Interface Layers: 3
Interface pattern spacing: 0.2
Support on build plate only: -//-
Don’t support bridges: CHECK
 
Speed
 
Speed for print movies
(We recommend that you try printing with the parameters listed below and then adjust the print speed until the printing quality is optimal for you)
Perimeters: 20 mm/s
Small perimeters: 20 mm/s
External perimeters: 20 mm/s
Infill: 50 mm/s
Solid: 30 mm/s
Top solid :  20 mm/s
Gaps: 20 mm/s
Bridges: 20 mm/s
Support material: 50 mm/s
 
Speed for non print movies
Travel: 100 mm/s
 
Modifiers
First layer speed: 10 mm/s
 
Acceleration control (Settings for advanced users, change these parameters only if you have sufficient 3D printing expertise)
Perimeters: 400 mm/s2
Infill: 400 mm/s2
Bridge: 400 mm/s2
First layer: 300 mm/s2
Default: 400 mm/s2
 
Auto speed (advanced)
Max print speed: 100 mm/s
Max volumetric speed: 0 mm3/s
 
Multiple Extruders
These settings only work for 3D printers with multiple extruders (not recommended for beginners)
 
Advanced
Extrusion width 
You can try setting all parameters in this section, except the First layer, to values between 0.75% of your nozzle diameter and 1.25% of your nozzle diameter. Adjusting them will help you work out the optimal parameters for the best quality for your print. As for the First layer, you can set it to 150% of the diameter of your nozzle for better adhesion to the build plate (for a nozzle with a diameter of 0.4 mm, the First layer extrusion width can be from 0.3 mm to 0.5 mm)
 
Overlap
Infill/perimeters overlap: 25%
 
Flow
Bridge flow ratio: 0.7
 
Other
-//-
Output options
-//-
Notes
-//-
Shortcuts
-//-
 
Filament Settings Tab
 
Filament
Filament
Color: -//-
Diameter: 1.75
Extrusion multiplier: 1
Density: -//-
Cost: -//-
(You can set these parameters yourself if you need)
 
Cooling
Enable
Keep fan always on: CHECK
Enable auto cooling: -//-
 
Fan settings
Fan speed
Min: 100% (for PLA, PETG) or 30% (for ABS, SBS)
Max: -//-
Bridges fan speed: 100%
Disable fan for the first: 1
 
Cooling thresholds
Enable fan if layer print time is below: -//-
Slow down if layer print time is below: -//-
Min print Speed: -//-
 
Custom G-code
-//-
Notes
-//-
 
Printer Settings Tab
 
General 
Size and coordinates
Bed shape: your 3D printer’s bed size
Z offset: 0
Capabilities
Extruders: 1
Has heated bed: CHECK
Firmware
G-code flavor: RepRap (Marlin/Sprinter)
Advanced
Use relative E distances: CHECK
 
Custom G-code
Use your 3D printer’s standard G-code. If you don't have it, you may use the example below.
Start G-code
M104 S(First_layer_temperature) 
M140  S(First_layer_bed_temperature)
G28 S(Parking)
M109 S(waiting_for_warm-up_nozzle) 
M190  S(waiting_for_warm-up_bed)
End G-code
M104 s0 ;turn off nozzle
M140 s0 ;turn off bed
G91
G1 Z1 
G28 X0 Y0 ;park
M84 ;disable motors
M107 ;disable cooling
 
Extruder 1
Size
Nozzle diameter: 0.4 mm
Layer height limits
Min: 0.05
Max: 0.3
Position
Extruder offset: -//-
Retraction
Length: 5.5-6.5 mm (1mm for a direct extruder)
Lift Z: 0-0.3 mm
Speed: 30 - 40 mm/s
Extra length on restart: 0 mm
Minimum travel after retraction: 2 mm
Retract on layer change: -//- (you can try to enable this parameter)
Wipe while retracting: -//-  (you can try to enable this parameter)
 

PrusaSlicer printing recommendations:

 
These basic 3D printing settings recommendations for beginners were tested in PrusaSlicer 2.3.1. Test models were printed on Ultimaker 2, Creality Ender 3, Creality Cr-10S pro v2, Anycubic I3 Mega, Anycubic I3 MegaS, Anycubic Vyper with PLA and PETG filaments.
 
Note:
- You can upscale your 3D printing models. Downscaling is not recommended - it can make smaller parts of the model unprintable, distort the model’s level of detail and result in assembly issues.
- All connectors should be printed at 100% Infill.
- When printing Lock connectors, we recommend setting the “Brim width” parameter to 0 in the "Skirt and Brim" print settings. In that way, the Locks will be 3D printed with a Skirt only. 
 
In order to see all the parameters listed below, you need to enable the Expert mode in the PrusaSlicer’s settings.
 
Print Settings Tab
 
Layers and perimeters
Layer height:
Layer Height: 0.1-0.2
First layer height: 0.2-0.3
Vertical shells:
Perimeters: 2-3
Spiral vase: OFF
Horizontal shells:
Solid layers: 8 (for 0.1 Layer Height) or 4 (for 0.2 Layer Height)
Minimum shell thickness: 0.8
Quality (slower slicing)
Extra perimeters if needed: CHECK
Ensure vertical shell thickness: -//-
Avoid crossing perimeters:  CHECK
Detect thin walls: -//-
Detect bridging perimeters:  CHECK
Advanced: 
Seam position: Aligned
External perimeters first: -//-
 
Infill
Infill
Fill Density: 10%
Fill Pattern: Rectilinear
Top Fill Pattern: Monotonic
Bottom fill pattern: Monotonic
Reducing printing time:
Combine infill every: 1
Only infill where needed: -//-
Advanced:
Solid Infill every: 0
Fill angle: 45
Solid Infill threshold area: 70
Bridging angle: 0
Only retract when crossing perimeters: CHECK
Infill before perimeters: -//-
 
Skirt and brim
Skirt
Loops (minimum): 3
Distance from Object: 5
Skirt Height: 1 (for PLA and PETG)
Draft Shield: -//-
Minimal filament extrusion length: 50
Brim
Brim width: (5-8 mm is optional for small prints that have bad adhesion to the build plate)
 
Support material
Support Material:
Generate Support material: -//- (enable this parameter if your model requires supports)
Auto generated supports: CHECK
Overhang threshold: 40-60
Enforce support for the first: 0
Raft:
Raft Layers: 0
Options for Support material and Raft:
Contact Z distance: 0.2
Pattern: Rectilinear 
With sheath around the support: CHECK
Pattern spacing: 2.5
Pattern angle: 0
Interface Layers: 3
Interface pattern spacing: 0.2
Interface loops: -//-
Support on build plate only: -//-
XY separation between an object and its support: 50%
Don’t support bridges: CHECK
Synchronize with object layers: -//-
 
Speed
Speed for print moves
(We recommend that you try printing with the parameters listed below and then adjust the print speed until the printing quality is optimal for you)
Perimeters: 20 mm/s
Small perimeters: 20 mm/s
External perimeters: 20 mm/s
Infill: 50 mm/s
Solid infill: 30 mm/s
Top solid infill:  20 mm/s
Support material: 50 mm/s
Support material interface: 20 mm/s
Bridges: 20 mm/s
Gap fill: 20 mm/s
Ironing: 15 mm/s
 
Speed for non-print moves
Travel: 100 mm/s
 
Modifiers
First layer speed: 10 mm/s
 
Acceleration control (Settings for advanced users, change these parameters only if you have sufficient 3D printing expertise)
Perimeters: 400 mm/s2
Infill: 400 mm/s2
Bridge: 400 mm/s2
First layer: 400 mm/s2
Default: 400 mm/s2
 
Auto speed (advanced)
Max print speed: 100 mm/s
Max volumetric speed: 0 mm3/s
 
Multiple Extruders
These settings only work for 3D printers with multiple extruders (not recommended for beginners)
 
Advanced
Extrusion width 
 
You can try setting all parameters in this section, except the First layer, to values between 0.75% of your nozzle diameter and 1.25% of your nozzle diameter. Adjusting them will help you work out the optimal parameters for the best quality for your print. As for the First layer, you can set it to 150% of the diameter of your nozzle for better adhesion to the build plate (for a nozzle with a diameter of 0.4 mm, the First layer extrusion width can be from 0.3 mm to 0.5 mm)
 
Overlap
Infill/perimeter overlap: 25%
 
Flow
Bridge flow ratio: 0.7
 
Slicing
-//-
Other
Clip multi-part objects: CHECK
Output options
-//-
Notes
-//-
Dependencies
-//-
 
Filament Settings Tab
Filament
Filament
Color: -//-
Diameter: 1.75
Extrusion multiplier: 1
Density: -//-
Cost: -//-
Spool weight: -//-
(You can set these parameters yourself if you need)
Temperature
Сheck your filament manufacturer's temperature recommendations on the spool.
 
Cooling
Enable
Keep fan always on: CHECK
Enable auto cooling: -//-
Fan settings
Fan speed
Min: 100% (for PLA, PETG) or 30% (for ABS, SBS)
Max: -//-
Bridges fan speed: 100%
Disable fan for the first: 1
Full fan speed at layer: 3-4
Cooling thresholds
Enable fan if layer print time is below: -//-
Slow down if layer print time is below: -//-
Min print speed: -//-
 
Advanced
Print speed override
Max volumetric speed:
PLA: 14 MM3/S
ABS:  10 MM3/S
PETG:  14 MM3/S
HIPS: 10 MM3/S
(If you use the Volcano extruder for your printer, all parameters need to be increased x2)
 
Filament Overrides
-//-
Custom G-code
-//-
Notes
-//-
Dependencies
-//-
 
Printer Settings Tab
 
General 
Size and coordinates
Bed shape: your 3D printer’s bed size
Max print height: your 3D printer’s height
Z offset: 0
Capabilities
Extruders: 1
Single Extruder Multi Material: -//-
Firmware
G-code flavor: RepRap/Sprinter
G-code thumbnails: -//-
Supports stealth mode: -//-
Supports remaining times: -//-
Advanced
Use relative E distances: CHECK
Use firmware retraction: -//- (needs to be enabled in the firmware of your printer)
Use volumetric E: -//-
Enable variable layer height feature: CHECK
 
Custom G-code
Use your 3D printer’s standard G-code. If you don't have it, you may use the example below.
Start G-code
M104 S(First_layer_temperature) 
M140  S(First_layer_bed_temperature)
G28 S(Parking)
M109 S(waiting_for_warm-up_nozzle) 
M190  S(waiting_for_warm-up_bed)
End G-code
M104 s0 ;turn off nozzle
M140 s0 ;turn off bed
G91
G1 Z1 
G28 X0 Y0 ;park
M84 ;disable motors
M107 ;disable cooling
 
Extruder 1
Size
Nozzle diameter: 0.4 mm
Layer height limits
Min: 0.05
Max: 0.3
Position
Extruder offset: -//-
Retraction
Length: 5.5-6.5 mm (1 mm for a direct extruder)
Lift Z: 0-0.3 mm
Retraction Speed: 30 - 40 mm/s
Deretraction Speed: 0 mm/s
Extra length on restart: 0 mm
Minimum travel after retraction: 2 mm
Retract on layer change: -//- (you can try to enable this parameter)
Wipe while retracting: -//-  (you can try to enable this parameter)
Retract amount before wipe:
Notes
-//-
Dependencies
-//-

Comments

DP
Other author's 3D printings

Reviews

  • loading reviews..

Similar items

Browse more newly listed 3D printings