Make pre-order

(1)
small
cm: 3 w x 4 d x 3.5 h
in: 1.181 w x 1.575 d x 1.378 h
6
BUY FOR  $9.99

Source Files

|

Description

|

Printing Details

This 3D model consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Version 1 and Version 2 are the files for Mad Cat Mk II Weapon Kit optimized for 3D printing, the preview pictures of which you see above.

It is recommended:

  • to print Version 1 STL files on FDM/FFF 3D printers;
  • to print Version 2 STL files on DLP/SLA/SLS 3D printers.
      File Name File Size Time / Filament
      1_a_R (repaired).stl
      2.52 MiB 1 h 19 min
      1 m
      Download
      2_b_R (repaired).stl
      2.24 MiB 1 h 10 min
      1 m
      Download
      3_c_R (repaired).stl
      0.78 MiB 2 h 34 min
      1 m
      Download
      4_d_R (repaired).stl
      1.20 MiB 1 h 20 min
      1 m
      Download
      5_e_R (repaired).stl
      2.25 MiB 1 h 11 min
      1 m
      Download
      6_f_R (repaired).stl
      2.31 MiB 2 h 3 min
      1 m
      Download
      7_a_L (inverted) (repaire d).stl
      2.52 MiB 1 h 18 min
      1 m
      Download
      8_b_L (inverted) (repaire d).stl
      2.24 MiB 1 h 10 min
      1 m
      Download
      9_c_L (inverted) (repaire d).stl
      0.78 MiB 2 h 35 min
      1 m
      Download
      10_d_L (inverted) (repair ed).stl
      1.20 MiB 1 h 18 min
      1 m
      Download
      11_e_L (inverted) (repair ed).stl
      2.25 MiB 1 h 9 min
      1 m
      Download
      12_f_L (repaired).stl
      2.31 MiB 2 h 4 min
      1 m
      Download

      Are you familiar with Mad Cat Mk II 3D Printing Miniature?
      I'm sure yes! And now for you, this set of weapons that will turn your cat into a tiger! This will be an excellent addition for your robot. Powerful upgrade consisting of 5 sets which can decorate your model.

      Mad Cat Mk. II Enhanced
      Mad Cat Mk. II 2 Launchers on shoulders and rockets on the torso
      Mad Cat Mk. II 3 Rocket Launchers
      Mad Cat Mk. II 4 Laser Cannon
      Mad Cat Mk. II 5 Special Rocket Launchers and Gauss weapon

      Of course you can mix them and create your own unique set of weapons. But the best thing that is in this set the old-school Enhanced guns at angle of 45º. They are available in two versions, as open and closed. This is exactly the good news for fans of Mad Cat, since now their robot available in the best configuration. Joining of weapons is possible thanks to specially designed slots, but in order to change weapons in your arms you need to print a new model which is in this set so that the connection parts can be replaceable.
      And now it’s available for purchase on Gambody Marketplace!

      All files are made in very high quality and should be printed at 100% infill to make them solid.

      STL files for 3D printing have been checked for errors and corrected in Netfabb.

      Note: Before starting 3D printing the model, read the Printing Details for CURA 2.3.1 software.

      There are 44 parts for FDM version and 12 part for SLS.
      Scale:
      The robot's scale is 1/60. 17600/60 = 293 mm.
      Scale of weapon based on this numbers.

      Watch the video of Mad Cat MK || Weapon Kits shown from all sides at Gambody YouTube channel

      If you don’t have Mad Cat MkII 3D Printing Miniature you can purchase it and this set right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.
       

      ____________
      FAQ: 

      Where can I print a model if I have no printer?
      How to get started with 3D printing?
      How to set up my 3D printer?
      How to choose right 3D model print bed positioning? 
      How to paint printed figurine?

      If you want to 3D print this kit on an FDM 3D printer, we recommend scaling the model up three times and use the CURA 2.3.1 settings below.

      Quality

      Layer Height: 0.1 mm
      Initial Layer Height: 0.3 mm
      Line Width: 0.4 mm
      Wall Line Width: 0.4 mm
      Outer Wall Line Width: 0.4 mm
      Inner Wall(s) Line Width: 0.4 mm
      Top/Bottom Line Width: 0.4 mm
      Infill Line Width: 0.4 mm
      Skirt/Brim Line Width: 0.4 mm
      Support Line Width: 0.4 mm

      Shell

      Wall Thickness: 0.8 mm
      Wall Line Count: 2
      Top/Bottom Thickness: 0.8 mm
      Top Thickness: 0.8 mm
      Top Layers: 8
      Bottom Thickness: 0.8 mm
      Bottom Layers: 8
      Top/Bottom Pattern: Lines
      Outer Wall Inset: 0 mm
      Compensate Wall Overlaps: Check
      Compensate Outer Wall Overlaps: Check
      Compensate Inner Wall Overlaps: Check
      Horizontal Expansion: 0 mm
      Z Seam Alignment: Shortest

      Infill

      Infill Density: 25%
      Infill Line Distance: 3.2 mm
      Infill Pattern: Grid
      Infill Overlap Percentage: 10%
      Infill Overlap: 0.04 mm
      Skin Overlap Percentage: 5%
      Skin Overlap: 0.02 mm
      Infill Wipe Distance: 0.1 mm
      Infill Layer Thickness: 0.1 mm
      Gradual Infill Steps: 0
      Infill Before Walls: Check

      Material

      Enable Retraction: Check
      Retraction Extra Prime Amount: 0 mm3
      Retraction Minimum Travel: 0.8 mm
      Maximum Retraction Count: 90
      Minimum Extrusion Distance Window: 6.5 mm
      Standby Temperature: 175°C
      Nozzle Switch Retraction Distance: 16 mm
      Nozzle Switch Retraction Speed: 20 mm/s
      Nozzle Switch Retract Speed: 20 mm/s
      Nozzle Switch Prime Speed: 20 mm/s

      Speed

      Print Speed: 60 mm/s
      Infill Speed: 80 mm/s
      Wall Speed: 30 mm/s
      Outer Wall Speed: 30 mm/s
      Inner Wall Speed: 60 mm/s
      Top/Bottom Speed 15 mm/s
      Support Speed: 60 mm/s
      Support Infill Speed: 60 mm/s
      Travel Speed: 120 mm/s
      Initial Layer Speed: 15 mm/s
      Initial Layer Print Speed: 15 mm/s
      Initial Layer Travel Speed: 30 mm/s
      Skirt/Brim Speed 15 mm/s
      Maximum Z Speed: 0 mm/s

      Travel

      Combing Mode: All
      Avoid Printed Parts when Traveling: Check
      Travel Avoid Distance: 0.625 mm

      Cooling

      Enable Print Cooling: Check
      Fan Speed: 100%
      Regular Fan Speed: 100%
      Maximum Fan Speed: 100%
      Regular/Maximum Fan Speed Threshold: 10 s
      Regular Fan Speed at Height: 0.3 mm
      Regular Fan Speed at Layer: 2
      Minimum Layer Time: 5 s
      Minimum Speed: 10 mm/s

      Support

      Enable Support: Check
      Support Placement: Everywhere
      Support Overhang Angle: 30°
      Support Pattern: Zig Zag
      Connect Support ZigZags: Check
      Support Density: 30 %
      Support Line Distance: 1.3333 mm
      Support Z Distance: 0.1 mm
      Support Top Distance: 0.1 mm
      Support Bottom Distance: 0.1 mm
      Support X/Y Distance: 0.7 mm
      Support Distance Priority: Z overrides X/Y
      Minimum Support X/Y Distance: 0.2 mm
      Support Stair Step Height: 0.3 mm
      Support Join Distance: 2.0 mm
      Support Horizontal Expansion: 0.2 mm
      Use Towers: Check
      Tower Diameter: 3.0 mm
      Minimum Diameter: 3.0 mm
      Tower Roof Angle: 65°

      Build Plate Adhesion

      Build Plate Adhesion Type: Brim
      Skirt/Brim Minimum Length: 250 mm
      Brim Width: 8.0 mm
      Brim Line Count: 20
      Brim Only on Outside: Check

      Mesh Fixes

      Union Overlapping Volumes: Check

      Special Modes

      Print Sequence: All at Once
      Surface Mode: Normal

      Experimental

      Extra Skin Wall Count: 0

      Comments

      comments powered by Disqus
      Other author's 3D printings

      Tags

      MechWarrior Online, MWO, Battlemech, Battletech, Mad Cat, Weapon, Assembly, Mad Cat weapon kit

      Similar items

      Browse more newly listed 3D printings