Make pre-order

BattleTech Marauder 3D Model | Assembly Figure

cm: 13.3 w x 18.7 d x 25 h
in: 5.236 w x 7.362 d x 9.843 h
BUY FOR  $26.99

Source Files




Printing Details

This 3D model consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Version 4 and Version 5 are the new files for Marauder MWO 3D Model optimized for 3D printing, the preview pictures of which you see above.

It is recommended:

  • Version 1 STL files on FDM/FFF 1.0 3D printers - old version with old joints;
  • Version 2 STL files on FDM/FFF 2.0 3D printers - old updated version;
  • Version 3 STL files on FDM/FFF 3.0 3D printers - new version with new scale and new joints;
  • Version 4 STL files on FDM/FFF 3.1 3D printers - new version of knee and elbow joints;
  • Version 5 STL files on DLP/SLA/SLS 1.0 3D printers - new version with new scale and new joints.


File Name File Size Time / Filament
2 (repaired).stl
18.37 MiB 18 h 41 min
11 m
3 (repaired).stl
7.92 MiB 7 h 20 min
4 m
G1 (repaired).stl
1.63 MiB 3 h 15 min
2 m
G2 (repaired).stl
0.77 MiB 1 h 9 min
1 m
G3 (repaired).stl
0.89 MiB 33 min
<1 m
G4 (repaired).stl
2.98 MiB 1 h 39 min
1 m
G5 (repaired).stl
2.78 MiB 59 min
1 m
L1 (repaired).stl
1.58 MiB 1 h 37 min
1 m
L10 (repaired).stl
0.21 MiB 13 min
<1 m
L11 (repaired).stl
0.50 MiB 50 min
<1 m
L12 (repaired).stl
0.16 MiB 47 min
1 m
L13 (repaired).stl
0.31 MiB 54 min
1 m
L14 (repaired).stl
0.24 MiB 37 min
<1 m
L15 (repaired).stl
1.46 MiB 4 h 36 min
3 m
L16 (repaired).stl
2.37 MiB 4 h 46 min
3 m
L17 (repaired).stl
0.31 MiB 46 min
<1 m
L2 (repaired).stl
0.16 MiB 1 h 6 min
1 m
L3 (repaired).stl
0.34 MiB 8 min
<1 m
L4 (repaired).stl
0.15 MiB 37 min
<1 m
L5 (repaired).stl
0.34 MiB 21 min
<1 m
L6 (repaired).stl
4.12 MiB 4 h 47 min
3 m
L7 (repaired).stl
0.29 MiB 57 min
<1 m
L8 (repaired).stl
3.02 MiB 6 h 60 min
4 m
L9 (repaired).stl
1.90 MiB 4 h 5 min
2 m
R1 (repaired).stl
1.58 MiB 1 h 37 min
1 m
R10 (repaired).stl
0.21 MiB 13 min
<1 m
R11 (repaired).stl
0.50 MiB 50 min
<1 m
R12 (repaired).stl
0.16 MiB 47 min
1 m
R13 (repaired).stl
0.31 MiB 54 min
1 m
R14 (repaired).stl
0.24 MiB 36 min
<1 m
R15 (repaired).stl
1.46 MiB 4 h 36 min
3 m
R16 (repaired).stl
2.37 MiB 4 h 46 min
3 m
R17 (repaired).stl
0.31 MiB 46 min
<1 m
R2 (repaired).stl
0.16 MiB 1 h 6 min
1 m
R3 (repaired).stl
0.34 MiB 8 min
<1 m
R4 (repaired).stl
0.15 MiB 37 min
<1 m
R5 (repaired).stl
0.34 MiB 21 min
<1 m
R6 (repaired).stl
4.12 MiB 4 h 50 min
3 m
R7 (repaired).stl
0.29 MiB 57 min
<1 m
R8 (repaired).stl
3.03 MiB 6 h 60 min
4 m
R9 (repaired).stl
1.90 MiB 4 h 4 min
2 m
1 (repaired).stl
10.62 MiB 29 h 36 min
18 m

Marauder is another bipedal Mech from the BattleTech Universe. The Marauder design has somehow detached from the traditional Mechs’ humanoid look and resembles more to a robot vehicle. The Mech was built to be used in attacks and as a fire support BattleMech.

BattleTech Marauder 3D model is what the BattleTech Universe bipedal vehicle is. Its distinguishable feature is the GM Whirlwind Autocannon/5 that crowns its torso.

Marauder Mech 3D model is what you need to add to your army of bipedal vehicles. Equipped with long-range firepower PPCs and the Autocannon, the Mech could withstand heavy combat.

Marauder model for 3D printing is a poseable figurine, with workable legs and hands. The Mech’s torso is also operational, rotating at 360°.

Bonus: Marauder 3D model’s weapons are completely removable. This means you will be able to remove the model’s regular weapons pack and attach other, upgraded weapons.

Modeling BattleTech Marauder 3D model

All in all, the 3D model consists of 42 parts. Every part is modeled in Autodesk Maya 3D modeling program. Every part has undergone thorough checking in Netfabb, to ensure error-free and accurate 3D printing.

BattleTech Marauder action figurine is a 3D model optimized for 3D printing on any type of 3D printers: SLA/SLS and FFF.

All parts are converted into STL file format. They can be easily handled in any slicing program, such as Cura 15.06 or Simplify3D.

Marauder 3D Print Model size after assembly

After 3D printing and assembling the model, Marauder BattleTech 3D action figure will stand 250 mm tall, 135 mm wide, and 187 mm deep.

Add the poseable model to your collection of 3D printed Mechs.

Buy BattleTech Marauder 3D model by clicking the green button in the top right corner of the screen. Proceed to checkout, provide your PayPal or credit card information and download Marauder 3D model STL files.

Note: You can now 3D print your model with 3DHubs directly from our site. Click the Print with 3DHubs button. You will be redirected to their platform, where you can enter your city of residence and choose from the hundreds of available 3D printing service providers.

*** Version 2 of Marauder STL Files is now available for purchase and download. The model parts are solid and adapted to be 3D printed using any slicing program. 

On 28.11.2016 the model files have been optimized and made solid. They now are adapted to be 3D printed using any slicing program. 3D model files are already available for purchase and download. 


On 03.11.2017 new scale and new version of joints have been added.


Now, the 3D Model of Marauder MWO is available in two scale: 1/60 for Version 3 (FDM/FFF) and 1/100 for Version 4 (DLP/SLA/SLS).

There are 46 parts in Version 3 (FDM/FFF) and 8 parts for Version 4 (DLP/SLA/SLS).

Version 3 (FDM/FFF):
- Is 1:60 scale and after being printed will stand 250 mm tall, 133 mm wide, 187 mm deep;
- Made with new joints;
- All movable elements of the Marauder Mech were saved.

Version 4 (DLP/SLA/SLS):
- Is 1:100 scale and will stand 150 mm tall, 80 mm wide, 111 mm deep;
- Made with new joints;
- All movable elements of the Marauder Mech were saved;
- Has as few details as possible to keep printing costs down.

With new joints from Version 3 and Version 4 you will get next advantages:
1. Increases frictional force;
2. Possible to up scale or down scale the whole model;
3. Printable from any type of material;
4. Higher strength;
5. Material shrinkage does not affect at strength and friction.

STL files with new scale and new joints are already available for download in “Source files” tab for:
- Version 3 - STL files on FDM/FFF 3D printers;
- Version 4 - STL files on DLP/SLA/SLS 3D printers.

Watch the tutorial video on how to assemble Marauder MWO 3D Printing Miniature at Gambody YouTube channel


On 14.09.2018 new knee and elbow joints have been added.

Now the Marauder 3D model has new, more durable knee and elbow joints to improve the model’s stability. They reliably fix and allow changing the model’s pose. Due to the improved durability, the joints do not wear off because of frequent changes in the model’s pose. The new knee and elbow joints are simpler to print and better fit the overall design and appearance of the model. They are also completely replaceable, and you don’t have to reprint the whole model to replace one of these parts.

Now this model contain parts of Locks. One part of Lock (47_Ge_lock_10H_(x4)) you need to print 4 times.

STL files with new joints are already available for download in “Source files” tab FFF/FDM 3.1 Version.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.4.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for Cura and Simplify3D softwares.

Cura printing recommendations:

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.


- You can print new joints from Version 3 and Version 4 with 20-30% infill. 
- With the new joints from Version 3 and Version 4 you can up scale or down scale the whole model.

- All parts of connectors should be printed at 100% infill.

To avoid printing problems, we recommend the following settings:

Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill Density: 20% (use 100% for connectors)
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Print Speed: 45 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s 
     Support Infill Speed: 45 mm/s
Travel Speed: 60 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 30 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.6562 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 50°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 1.3333 mm
Support Z Distance: 0.3 mm
    Support Top Distance: 0.3 mm
    Support Bottom Distance: 0.3 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 18 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Extruder 1 Temperature: 210
Heated Bed: 60

Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Unsupported area threshold: 20.0 sq m


comments powered by Disqus
Other author's 3D printings


mechwarrior, battlemech, marauder, battletech, mwo, battletech marauder, video games, assembly models, poseable 3d model, New Joints, New Scale

Similar items

Browse more newly listed 3D printings