Make pre-order

Martian 3D Printing Figurine | Assembly

cm: 12.3 w x 11.2 d x 20.5 h
in: 4.843 w x 4.409 d x 8.071 h
BUY FOR  $24.99

Source Files




Printing Details

This 3D Figurine consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Martian 3D Printing Figurine comes in 4 versions for each 3D printer type (FFF/FDM, DLP/SLA and SLS). Files for each version are available for download after the purchase.

Detailed information about this 3D printing figurine is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
47.63 MiB 5 h 12 min
3 m
44 x 38 x 54 Download
2_space_suit_FDM(repaired ).stl
23.63 MiB n.a.
51 x 51 x 55 Download
62.07 MiB 7 h 5 min
4 m
4_arm_R_1_FDM(repaired).s tl
32.22 MiB 50 min
<1 m
24 x 33 x 19 Download
5_arm_R_2_FDM(repaired).s tl
32.74 MiB n.a.
14 x 13 x 30 Download
6_hand_R_FDM(repaired).st l
17.99 MiB 30 min
<1 m
7_arm_L_1_FDM(repaired).s tl
30.63 MiB 41 min
<1 m
8_arm_L_2_FDM(repaired).s tl
35.00 MiB 32 min
<1 m
9_hand_L_FDM(repaired).st l
17.70 MiB 30 min
<1 m
10_leg_R_FDM(repaired).st l
41.30 MiB 2 h 41 min
2 m
11_foot_R_FDM(repaired).s tl
34.90 MiB 59 min
1 m
27 x 25 x 40 Download
12_leg_L_FDM(repaired).st l
39.30 MiB 2 h 40 min
2 m
36 x 36 x 57 Download
13_foot_L_FDM(repaired).s tl
31.63 MiB 1 h 3 min
1 m
20 x 27 x 44 Download
14_hoses_connector_FDM(re paired).stl
15.01 MiB 12 min
<1 m
12 x 20 x 9 Download
15_hose_1_FDM(repaired).s tl
13.57 MiB 37 min
<1 m
18 x 26 x 35 Download
16_hose_2_FDM(repaired).s tl
13.37 MiB 38 min
<1 m
22 x 19 x 37 Download
17_baloon_1_FDM(repaired) .stl
22.64 MiB 1 h 42 min
1 m
19 x 55 x 25 Download
18_baloon_2_FDM(repaired) .stl
22.12 MiB 1 h 39 min
1 m
19_baloon_connector_1_FDM (repaired).stl
16.31 MiB 11 min
<1 m
20_baloon_connector_2_FDM (repaired).stl
16.75 MiB 11 min
<1 m
8 x 10 x 12 Download
22_laser_rifle_2_FDM(repa ired).stl
14.27 MiB 33 min
<1 m
10 x 10 x 27 Download
23_laser_rifle_3_FDM(repa ired).stl
7.54 MiB 15 min
<1 m
7 x 12 x 24 Download
24_platform_FDM(repaired) .stl
35.56 MiB 6 h 32 min
3 m
Keychain (repaired).stl
0.35 MiB 23 min
<1 m
30 x 30 x 2 Download
Tag (repaired).stl
1.70 MiB 1 h 16 min
1 m
150 x 18 x 5 Download
2_1_space_suit_1_FDM(repa ired).stl
17.61 MiB 3 h 21 min
2 m
51 x 27 x 55 Download
2_2_space_suit_2_FDM(repa ired).stl
19.88 MiB 3 h 32 min
2 m
51 x 27 x 55 Download
21_laser_rifle_1_FDM(repa ired).stl
39.84 MiB 2 h 27 min
1 m
82 x 18 x 42 Download


Ack Ack Ack!!”

The theme of an alien invasion in movies isn’t a novelty for sci-fi enthusiasts, but there’s hardly a movie like 1996 Mars Attacks! comedy. Directed by Tim Burton, Mars Attacks! pays tribute to the genre of science fiction of the 1960s, portraying the Martian army extremely lethal in a wonderfully silly manner! An all-star cast of Tim Burton’s cult B-movie is led by the great Jack Nicholson who plays the US President James Dale. However, the brightest stars of the film are indeed the large-brained comical Martians who seem to invade the Earth for the sole purpose of having fun! One of our contributing 3D artists decided to capture in 3D printing form one of the representatives of the merciless Martians and dedicated around 145 hours working on the project. The 3D printing Martian is very determined, angry and is clearly ready for action! The figurine is pointing a large blaster rifle (although it seems to be aiming at no particular target). The alien’s exaggerated eyes are full of hatred and its toothy jaws are open in a crazy laugh. The author of the model made sure to pay careful attention to every little detail and extraterrestrial texture of the model, so we urge you to take a closer look at the patters of the Martian’s massive brain or at the finely detailed surface of its sturdy armour. The 3D printing alien is equipped with a pair of nitrogen tanks, intricately connected with a system of pipes, as the race of alien destroyers doesn't breathe in Earth's atmosphere. Mars Attacks! is a fan-loved movie full of goofiness, unexpected twists, A-list actors, and one-of-a-kind villains. Now you’ve got a perfect chance to tame a Martian yourself - just print the awesome 3D printing figurine!


Martian figurine for 3D printing is a static assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 45 hours in total. The alien’s anatomy and proportions were thoroughly reviewed during the moderation process for the hostile extra-terrestrial to be depicted harmoniously in the intended attacking pose. The model’s cutting was chosen by our team to minimise the amount of filament needed for generated support and some of the parts were hollowed out for you to save resin in the figurine’s Eco version. In order to conceal the places where the assembly parts of the model must be connected, the figurine was cut along the contour of the martian’s armour seams. For you to achieve the cleanest 3D printed result, the figurine’s head, hands, boots, alien blaster, nitrogen tanks, etc. are provided as separate files. The bubble helmet also comes separately in order for you to print it with the transparent material. The alien blaster and the nitrogen attachment were split element by element for the cleanest 3D printed result possible. All the assembly parts come in STL files in recommended positions that were worked out in order to ensure the smoothness of the details’ surfaces after printing and so that the 3D printing beginners won't face difficulties when placing the parts on a build plate. When downloading any figurine's file you will also receive "Assembly Manual" for FFF/FDM 1.0 and DLP/SLA 1.0 versions in PDF format.

The figurine is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from the average height of Martian which is 1500 mm. The 3D printing figurine's chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS versions.


FFF/FDM 1.0 version features:
- Contains 24 parts;
- A printed model is 205 mm tall, 123 mm wide, 112 mm deep;
- Martian can be displayed wearing a bubble helmet or without it;
- The one-piece bubble helmet (2_space_suit_FDM) won't fit the Martian's head, but can be used as a part of a diorama;
- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:
- Contains 11 parts;
- A printed model is 103 mm tall, 62 mm wide, 56 mm deep;
- Martian can be displayed wearing a bubble helmet or without it;
- The one-piece bubble helmet (2_space_suit_SLA) won't fit the Martian's head, but can be used as a part of a diorama;
- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

DLP/SLA Eco 1.0 version features:
- Contains 11 parts;
- A printed model is 103 mm tall, 62 mm wide, 56 mm deep;
- Martian can be displayed wearing a bubble helmet or without it;
- The one-piece bubble helmet (2_space_suit_SLA) won't fit the Martian's head, but can be used as a part of a diorama;
- Contains some hollowed out parts to save resin.

SLS 1.0 version features:
- Made as a solid one-piece figurine;
- A printed model is 103 mm tall, 62 mm wide, 56 mm deep;
- Contains 3 parts - one-piece model and the figurine with the platform separated.


- STL files of Martian 3D Figurine for 3D printing which consist of 49 parts;
- 4 versions of files for this model for FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS;
- High-poly detailed figurine of Martian;
Assembly Manual for FFF/FDM 1.0 and DLP/SLA 1.0 versions in PDF format;
- Detailed settings that we provide as a recommendation for Cura 3.5.1, Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get the figurine of Martian​ for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Martian 3D Printing Figurine at Gambody YouTube channel.

Also, you may like other Villains 3D Printing Figurines.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.5.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for CuraSimplify3D and Slic3r softwares.

Cura printing recommendations:

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

To avoid printing problems, we recommend the following settings:

Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s 
     Support Infill Speed: 45 mm/s
Travel Speed: 45 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 45 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.6562 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 2.2 mm
Support Z Distance: 0.13 mm
    Support Top Distance: 0.13 mm
    Support Bottom Distance: 0.13 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 15 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Extruder 1 Temperature: 210
Heated Bed: 60

Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
  Detect thin walls: Check
  Detect bridging perimeters: Check
  Seam position: Random
  Fill desity: 20%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
  Infill/Perimeters overlap: 20%
  Bridge flow ratio: 0.95
  XY Size Compensation: 0 mm
  Threads: 8
  Resolution: 0 mm


comments powered by Disqus

Similar items

Browse more newly listed 3D printings