Make pre-order

MadCat Classic MWO 3D Printing Model | Assembly + Action

cm: 16.5 w x 11.8 d x 21 h
in: 6.496 w x 4.646 d x 8.268 h
BUY FOR  $26.99

Source Files




Printing Details

This 3D Model consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

MadCat Classic MWO 3D Printing Model comes in 2 versions for FFF/FDM 3D printers type. Files for each version are available for download after the purchase.

Detailed information about this model is available in the DESCRIPTION section.

File Name File Size Time / Filament
01_madcat_hip (repaired). stl
0.01 MiB 21 min
<1 m
02_madcat_hip_b (repaired ).stl
0.25 MiB 1 h 40 min
1 m
03_madcat_hip_c (repaired ).stl
0.13 MiB 16 min
<1 m
04_madcat_hip_d (repaired ).stl
0.47 MiB 1 h 35 min
1 m
05_madcat_hip_e (repaired ).stl
0.03 MiB 18 min
<1 m
06_madcat_thigh_LEFT (rep aired).stl
0.05 MiB 1 h 20 min
1 m
07_madcat_thigh_Right (re paired).stl
0.06 MiB 1 h 21 min
1 m
08_madcat_thigh_b (repair ed).stl
0.32 MiB 30 min
<1 m
09_madcat_thigh_c (repair ed).stl
0.09 MiB 26 min
<1 m
10_madcat_thigh_d (repair ed).stl
0.03 MiB 7 min
<1 m
11_madcat_joint_tpe_01 (r epaired).stl
0.07 MiB 8 min
<1 m
12_madcat_knee_joint_righ t (repaired).stl
0.02 MiB 29 min
<1 m
13_madcat_knee_joint_left (repaired).stl
0.03 MiB 28 min
<1 m
14_madcat_knee_joint_cove r (repaired).stl
0.00 MiB 8 min
<1 m
15_madcat_foot (repaired) .stl
0.13 MiB 1 h 23 min
1 m
16_madcat_foot_cover (rep aired).stl
0.65 MiB 35 min
<1 m
17_madcat_foot_vent (repa ired).stl
0.03 MiB 3 min
<1 m
18_madcat_ankle_ball_join t (repaired).stl
0.22 MiB 29 min
<1 m
19_madcat_ankle_ball_join t_TPE_02 (repaired).stl
0.27 MiB 17 min
<1 m
20_madcat_toe_1 (repaired ).stl
0.05 MiB 15 min
<1 m
21_madcat_toe_2 (repaired ).stl
0.06 MiB 20 min
<1 m
22_madcat_toe_3 (repaired ).stl
0.05 MiB 15 min
<1 m
23_madcat_toe_4 (repaired ).stl
0.06 MiB 18 min
<1 m
24_madcat_foot_paw (repai red).stl
0.01 MiB 16 min
<1 m
25_madcat_shank_01 (repai red).stl
0.02 MiB 1 h 29 min
1 m
26_madcat_shank_02 (repai red).stl
0.26 MiB 40 min
<1 m
27_madcat_shank_tank_01 ( repaired).stl
0.08 MiB 22 min
<1 m
28_madcat_shank_tank_02 ( repaired).stl
0.08 MiB 22 min
<1 m
29_madcat_shank_heatsink (repaired).stl
0.01 MiB 7 min
<1 m
30_madcat_shank_heatsink_ fin (repaired).stl
0.04 MiB 6 min
<1 m
31_madcat_knee_joint_stop (repaired).stl
0.08 MiB 11 min
<1 m
32_madcat_joint_tpe_03 (r epaired).stl
0.30 MiB 14 min
<1 m
33_madcat_body_07 (repair ed).stl
0.22 MiB 2 h 7 min
1 m
34_madcat_body_06 (repair ed).stl
0.03 MiB 1 h 20 min
1 m
35_madcat_body_04 (repair ed).stl
0.22 MiB 7 h 34 min
4 m
36_madcat_body_05 (repair ed).stl
1.19 MiB 6 h 12 min
4 m
36_madcat_body_05(no logo ) (repaired).stl
0.75 MiB 6 h 12 min
4 m
37_madcat_body_10 (repair ed).stl
0.02 MiB 16 min
<1 m
38_madcat_body_11 (repair ed).stl
0.02 MiB 16 min
<1 m
39_madcat_body_01 (repair ed).stl
0.05 MiB 25 min
<1 m
40_madcat_body_03 (repair ed).stl
0.30 MiB 31 min
<1 m
41_madcat_body_02 (repair ed).stl
0.04 MiB 25 min
<1 m
42_madcat_body_08 (repair ed).stl
0.07 MiB 28 min
<1 m
43_madcat_body_08_pin (re paired).stl
0.05 MiB 7 min
<1 m
44_madcat_2nd_cannon (rep aired).stl
0.17 MiB 30 min
<1 m
45_madcat_arm_01 (repaire d).stl
0.30 MiB 26 min
<1 m
46_madcat_arm_02 (repaire d).stl
0.06 MiB 17 min
<1 m
47_madcat_arm_03 (repaire d).stl
0.75 MiB 30 min
<1 m
48_madcat_body_12 (repair ed).stl
0.05 MiB 23 min
<1 m
49_madcat_rocket_box (rep aired).stl
0.06 MiB 2 h 28 min
1 m
50_madcat_rocket_box_cove r (repaired).stl
0.22 MiB 31 min
<1 m
51_madcat_rocket (repaire d).stl
6.51 MiB 21 min
<1 m
52_madcat_wrist (repaired ).stl
0.09 MiB 31 min
<1 m
53_madcat_main_cannon_1 ( repaired).stl
0.08 MiB 1 h 20 min
1 m
54madcat_main_cannon_2 (r epaired).stl
0.04 MiB 13 min
<1 m
55_madcat_main_cannon_3 ( repaired).stl
0.20 MiB 8 min
<1 m
56_madcat_main_cannon_shi eld (repaired).stl
0.03 MiB 1 h 49 min
1 m
57_madcat_main_cannon_shi eld_2 (repaired).stl
0.01 MiB 11 min
<1 m
58madcat_main_cannon_4 (r epaired).stl
0.03 MiB 1 h 7 min
<1 m
59_madcat_wrist_pin (repa ired).stl
0.13 MiB 7 min
<1 m
60_madcat_main_cannon_02 (repaired).stl
0.48 MiB 31 min
<1 m


MadCat is a fast heavy MechWarrior that was first introduced in 2945 as a representative of the OmniMech Clan. Its design is so remarkable and distinctive that has eventually become emblematic of the BattleTech universe in general. Though its official name is Timber Wolf, the deadly Mech is widely known as MadCat bearing a certain resemblance both to Marauder (Mad) and Catapult (Cat). The first time the nickname was designated to the Mech was when Inner Sphere’s targeting computer couldn’t identify it between the two. MadCat is actually much more powerful than both MechWarriors. Hardly had it been created when Clan Wolf as well as any other Clan immediately understood its great value. Timber Wolf can boast an impressive combination of energy and missile weaponry that guarantees a considerable firepower during the hottest of confrontation.


The model is saved in STL files, a format supported by most 3D printers

FFF/FDM 2.0 version features:
- Contains 71 parts;
- Assembly kit includes Locks. One part of Lock (69_Ge_lock_10H_x19) needs to be printed 19 times;
- Action figure with movable legs and arms;
- All parts are divided in such a way that you will print them with the smallest number of support structures.

FFF/FDM 1.0 version features:
- Contains 112 parts;
- Made in classic pose;
- Action figure with movable legs and arms;

All STL files for 3D printing have been checked in Netfabb and no errors were shown.

Note: Before starting 3D printing the model, read the Printing Details for CURA 3.5.1Simplify3D or Slic3r Software.

There are 71 parts for FFF/FDM 2.0 version and 112 parts for FFF/FDM 1.0

Scale: MadCat actual height is 12600 mm. The model’s chosen scale is 1/60 for the FDM version.

FFF/FDM version dimensions:
A printed model is 210 mm tall, 165 mm wide, 118 mm deep;


- STL files of MadCat 3D Model for 3D printing which consist of 159 parts;
- 2 versions of files for this model for FFF/FDM 3D Printers;
- High-poly detailed model of MadCat Classic Mech Warrior;
- Detailed settings that we provide for Cura 3.5.1, Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get Model of MadCat Classic Mech Warrior for 3D Printing right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble MadCat Classic Mech Warrior 3D Printing Model at Gambody YouTube channel.

Also, you may like other Mech Warrior 3D Printing Models.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.5.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for CuraSimplify3D and Slic3r softwares.

Cura printing recommendations:

- You can up scale or down scale the whole model.
- Connectors should be printed at 100% infill.
- For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section

To avoid printing problems, we recommend the following settings:

Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill Density: 20% (for all parts of connectors use 100% infill)
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s 
     Support Infill Speed: 45 mm/s
Travel Speed: 45 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 45 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.6562 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 45°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 2 mm
Support Z Distance: 0.2 mm
    Support Top Distance: 0.2 mm
    Support Bottom Distance: 0.2 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 15 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Extruder 1 Temperature: 210
Heated Bed: 60

Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
  Detect thin walls: Check
  Detect bridging perimeters: Check
  Seam position: Random
  Fill desity: 20%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
  Infill/Perimeters overlap: 20%
  Bridge flow ratio: 0.95
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm


comments powered by Disqus


MADCAT, Mech, Mechwarrior, robots, assembly, battlemech, battletech, Action

Similar items

Browse more newly listed 3D printings