Make pre-order

Smaug the Golden 3D Printing Figurine | Assembly

cm: 40 w x 42 d x 25.2 h
in: 15.748 w x 16.535 d x 9.921 h

Source Files




Printing Details

This 3D Figurine consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Smaug the Golden 3D Printing Figurine comes in 4 versions for each 3D printer type (FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS). Files for each version are available for download after the purchase.

Detailed information about this 3D printing figurine is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
1_head_1_FDM(repaired).st l
11.32 MiB 3 h 39 min
2 m
50 x 77 x 33 Download
2_head_2_FDM(repaired).st l
11.55 MiB 7 h 39 min
4 m
51 x 47 x 101 Download
12.66 MiB 18 min
<1 m
17 x 22 x 11 Download
12.76 MiB 49 min
<1 m
26 x 38 x 15 Download
5_neck_1_FDM(repaired).st l
10.08 MiB 13 h 30 min
9 m
79 x 61 x 89 Download
6_neck_2_FDM(repaired).st l
13.16 MiB 17 h 14 min
12 m
77 x 82 x 104 Download
15.16 MiB 35 h 12 min
22 m
86 x 93 x 126 Download
8_tail_1_FDM(repaired).st l
15.31 MiB 21 h 28 min
13 m
58 x 73 x 144 Download
9_tail_2_FDM(repaired).st l
8.41 MiB 12 h 12 min
9 m
60 x 69 x 122 Download
10_tail_3_FDM(repaired).s tl
10.46 MiB 2 h 48 min
2 m
31 x 43 x 68 Download
11_tail_4_FDM(repaired).s tl
11.38 MiB 3 h 2 min
2 m
25 x 52 x 106 Download
12_tail_5_FDM(repaired).s tl
11.85 MiB 1 h 33 min
1 m
20 x 31 x 80 Download
13_leg_L_1_FDM(repaired). stl
9.25 MiB 5 h 59 min
4 m
47 x 72 x 39 Download
14_leg_L_2_FDM(repaired). stl
9.95 MiB 3 h 3 min
2 m
32 x 51 x 50 Download
15_foot_L_FDM(repaired).s tl
10.03 MiB 2 h 8 min
1 m
53 x 62 x 27 Download
16_leg_R_1_FDM(repaired). stl
9.84 MiB 5 h 24 min
3 m
39 x 56 x 58 Download
17_leg_R_2_FDM(repaired). stl
8.02 MiB 3 h 12 min
2 m
35 x 57 x 45 Download
18_foot_R_FDM(repaired).s tl
12.17 MiB 2 h 5 min
1 m
71 x 44 x 30 Download
19_wing_L_1_FDM(repaired) .stl
7.76 MiB 8 h 22 min
5 m
84 x 47 x 88 Download
20_wing_L_2_FDM(repaired) .stl
10.13 MiB 19 h 56 min
12 m
166 x 51 x 129 Download
21_wing_L_3_FDM(repaired) .stl
9.81 MiB 9 h 13 min
5 m
60 x 67 x 147 Download
22_wing_L_4_FDM(repaired) .stl
5.09 MiB 1 h 46 min
1 m
66 x 18 x 96 Download
23_wing_L_5_FDM(repaired) .stl
9.57 MiB 20 h 56 min
12 m
222 x 53 x 140 Download
24_claws_L_1_FDM(repaired ).stl
1.48 MiB 11 min
<1 m
17 x 6 x 32 Download
25_claws_L_2_FDM(repaired ).stl
1.41 MiB 11 min
<1 m
20 x 10 x 30 Download
26_claws_L_3_FDM(repaired ).stl
1.27 MiB 9 min
<1 m
10 x 17 x 27 Download
27_wing_R_1_FDM(repaired) .stl
7.10 MiB 9 h 9 min
6 m
48 x 84 x 94 Download
28_wing_R_2_FDM(repaired) .stl
8.61 MiB 15 h 21 min
9 m
48 x 127 x 152 Download
29_wing_R_3_FDM(repaired) .stl
10.75 MiB 10 h 30 min
6 m
115 x 39 x 137 Download
30_wing_R_4_FDM(repaired) .stl
9.59 MiB 20 h 2 min
12 m
41 x 183 x 161 Download
31_claws_R_1_FDM(repaired ).stl
1.04 MiB 8 min
<1 m
13 x 9 x 27 Download
32_claws_R_2_FDM(repaired ).stl
1.04 MiB 9 min
<1 m
12 x 11 x 27 Download
33_claws_R_3_FDM(repaired ).stl
1.24 MiB 11 min
<1 m
15 x 9 x 34 Download
34_platform_1_FDM(repaire d).stl
17.23 MiB 43 h 9 min
25 m
133 x 133 x 54 Download
35_platform_2_FDM (repair ed).stl
15.21 MiB 31 h 17 min
18 m
121 x 122 x 83 Download
36_platform_3_FDM(repaire d).stl
18.53 MiB 63 h 19 min
37 m
133 x 133 x 87 Download
37_platform_4_FDM(repaire d).stl
14.36 MiB 25 h 20 min
15 m
122 x 122 x 61 Download
38_platform_5_FDM(repaire d).stl
18.15 MiB 60 h 12 min
36 m
133 x 133 x 83 Download
39_platform_6_FDM(repaire d).stl
13.28 MiB 27 h 41 min
16 m
121 x 122 x 76 Download
40_platform_7_FDM(repaire d).stl
15.30 MiB 48 h 37 min
28 m
133 x 133 x 68 Download
41_platform_8_FDM(repaire d).stl
12.77 MiB 22 h 55 min
13 m
122 x 122 x 50 Download
42_platform_9_FDM(repaire d).stl
19.22 MiB 60 h 24 min
35 m
133 x 133 x 74 Download
43_Ge_lock_10H(x74)_FDM(r epaired).stl
0.03 MiB 4 min
<1 m
18 x 10 x 2 Download
44_Ge_lock_7S(x13)_FDM(re paired).stl
0.02 MiB 3 min
<1 m
18 x 7 x 2 Download
Keychain (repaired).stl
0.35 MiB 23 min
<1 m
30 x 30 x 2 Download
Tag (repaired).stl
1.70 MiB 1 h 16 min
1 m
150 x 18 x 5 Download


The notable fire drake of the Lonely Mountain or the last great dragon to exist is an essential part of any Middle-earth universe fan’s 3D printed collection. When choosing the setting to depict his Smaug the Golden figurine in, the author of the dragon for 3D printing most likely was drawing inspiration from the original illustration provided by J.R.R. Tolkien titled “Conversation with Smaug”. The dragon is pictured sprawled on the wealth of the inestimable hoard in the depth of his mountain lair. The Hobbit film trilogy, without doubt, did greatly facilitate the 3D artist’s creative process but nevertheless, the figurine's sculpting took its author 125 hours in total. One can suppose that the Smaug 3D printing figurine shows the beast a mere seconds after being awakened from his slumber by the group of curious Dwarves who had the audacity to claim the ancient treasure from the dragon. Smaug the Chiefest and Greatest of Calamities, as Bilbo once addressed the dragon, turned out to be much larger than the Dwarves had expected and just as greedy as one may assume. The way the Smaug for 3D printing is towering above his great treasures proves that he has no intention to let his guard down - the Lonely Mountain’s wealth belongs solely to its rightful possessor, the King under the Mountain. 


Smaug the Golden 3D printing figurine is a static assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 46 hours in total. The model’s cutting was chosen by our team to minimise the amount of filament needed for generated support and some of the parts were hollowed out for you to save the resin. The figurine was divided into as many assembly parts as needed to fit even the smallest 3D printers' build plates and for you to nevertheless receive a large dragon after the assembly. The Smaug's head was split up for you to print the jaws preserving all the teeth's finest details. All the assembly parts are provided in STL files in recommended positions that were worked out so to ensure the smoothness of the details’ surfaces after printing and that the 3D printing beginners won't face difficulties when placing the parts on a build plate. All the parts have special connecting elements for you to assemble the figurine in the easiest way possible and there are locks provided to connect the details if you don’t want to glue the parts. It is especially convenient for those who are going to paint the model.

The figurine is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from the dragon's actual length that is 130000 mm. The 3D printing figurine's chosen scale is 1/100 for the FFF/FDM version and 1/200 for the DLP/SLA/SLS versions.


FFF/FDM version features:
- Contains 44 parts;
- A printed model is 252 mm tall, 400 mm wide, 420 mm deep;
- Assembly kit includes locks to connect the parts without glue. One lock 43_Ge_lock_10H(x74) needs to be printed 74 times. The second lock 44_Ge_lock_7S(x13)​ needs to be printed 13 times;
- Made with a platform to resemble the mountain of golden treasures;
- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA version features:
- Contains 13 parts;
- A printed model is 126 mm tall, 200 mm wide, 210 mm deep;
- Made with a platform to resemble the mountain of golden treasures;
- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

DLP/SLA Eco version features:
- Same as the DLP/SLA version, but contains parts hollowed out to save resin.

SLS version features:
- Same as DLP/SLA one but made as a solid figurine; 
- Contains 3 parts - a one-piece model and the figurine with the platform separated.


- STL files of Smaug the Golden 3D Figurine for 3D printing which consist of 73 parts;
- 4 versions of files for this model for FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS;
- High-poly detailed figurine of Smaug the Golden;
- Detailed settings that we provide as a recommendation for Cura , Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get the figurine of Smaug the Golden for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Smaug the Golden 3D Printing Figurine at Gambody YouTube channel.

Also, you may like other Lord of the Rings 3D Printing Figurines.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

Below you can find printing recommendations for CuraSimplify3D and Slic3r software.

Cura printing recommendations:

These are basic settings that were tested in Cura 4.8.0 slicer. 

The test models were printed on Ultimaker 2, Creality Ender 3, Creality CR-10S Pro V2, Anycubic I3 Mega, Anycubic I3 MegaS 3D printers with PLA and PETG filaments.

Disclaimer: The following printing settings are a recommendation, not an obligation. The parameters can vary depending on the peculiarities of your 3D printer, the material you use and especially the particular assembly part at hand. Each part that any model comprises often needs preliminary review and you are free to tweak the settings the way you find suitable.

- You can scale up the model (downscaling is not recommended!);
- All connectors should be printed at 100% Infill;
- For all parts of locks (“ge_lock” in “Source files”) you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

Layer Height: 0.12 mm (you can also set Layer Height at 0.16 or 0.2mm for 0.4mm nozzles)
Initial Layer Height: 0.2 mm (carefully level the print bed and keep your Initial Layer Height the same as the main Layer Height)

Line Width: 0.4 mm
Wall Line Width: 0.4 mm
Outer Wall Line Width: 0.4 mm
Inner Wall(s) Line Width: 0.4 mm
Top/Bottom Line Width: 0.4 mm
Infill Line Width: 0.4 mm
Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm

Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
Wall Line Count: 2

Outer Wall Wipe Distance: 0.3 mm
Top Surface Skin Layers: 0

Top/Bottom Thickness: 0.6 mm
Top Thickness: 0.6 mm
Top Layers: 5
Bottom Thickness: 0.6 mm
Bottom Layers: 5
Initial Bottom Layers: 5

Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Optimize Wall Printing Order: Check

Compensate Wall Overlaps: Check
Compensate Inner Wall Overlaps: Check

Minimum Wall Flow: 0%
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Hole horizontal expansion: 0

Z Seam Alignment: User Specified
Z Seam Position: Back
Z Seam X: Average length of your printer’s plate (e.g.”150” if your plate is 300mm on the X-axis)
Z Seam Y: A value higher than the length of your plate on the Y-axis (e.g. 700)

Seam Corner Preference: Hide Seam
Extra Skin Wall Count: 1
Skin Overlap Percentage: 10%
Skin Overlap 0.04 mm

Infill Density: 20% (for all smaller parts and for all parts of connectors use 100% Infill)
Infill Pattern: Triangles
Connect Infill Lines: Check
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Line Multiplier: 1
Extra Infill Wall Count: 0

Infill Overlap Percentage: 10-20%
Infill Overlap: 0.04 mm

Skin Overlap Percentage: 5%
Skin Overlap: 0.02 mm

Infill Wipe Distance: 0 mm
Infill Layer Thickness: 0.24 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2

Skin Removal Width: 0.8 mm
Top Skin Removal Width: 0.8 mm
Bottom Skin Removal Width: 0.8 mm

Skin Expand Distance: 0.8
Top Skin Expand Distance: 0.8
Bottom Skin Expand Distance: 0.8

Maximum Skin Angle for Expansion: 90˚
Minimum Skin Width for Expansion: 0.0
Skin Edge Support Thickness: 0
Skin Edge Support Layers: 0

Initial Layer Flow: 100%
Printing Temperature: See your filament settings
Initial Printing Temperature: Your filament settings
Final Printing Temperature: Your filament settings
Build Plate Temperature: Your filament settings
Build Plate Temperature Initial Layer: Your filament settings + 5°
Flow: 100% (Important! If you face difficulty printing the model, you may need to adjust the Flow parameter. You may research the topic using the Internet or seek assistance at our Customer Support Team at


You can increase the printing Speed by 20% when you print simple objects. For small/thin parts you need to decrease the Speed by 25% - 50%.

Print Speed: 50 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 25 mm/s
          Outer Wall Speed:25 mm/s
          Inner Wall Speed: 50 mm/s

Top/Bottom Speed: 25mm/s
Support Speed: 25 mm/s 
          Support Infill Speed: 45 mm/s
          Support Interface Speed: 25 mm/s
                Support Roof Speed: 25 mm/s
                Support Floor Speed: 25 mm/s

Travel Speed: 80 mm/s
Initial Layer Speed: 80 mm/s
Initial Layer Print Speed: 20 mm/s
Initial Layer Travel Speed: 80 mm/s

Skirt/Brim Speed: 20 mm/s
Z  Hop Speed: 5 mm/s
Number of Slower Layers: 2
Enable Acceleration Control: Check

When printing simple objects, you need to set all Acceleration parameters at 500 mm/s. For small/thin parts you need to decrease the Acceleration by 50% - 70%.

Enable Retraction: Check
Retraction Distance: 4-8 mm, 1-3 mm for Direct Extruder (This is the most important retraction parameter. You can find your optimal value of Retraction Distance by printing any test object, e.g. bridges, towers etc.)

Retraction Speed: 25mm/s
Retraction Retract Speed: 25 mm/s
Retraction Prime Speed: 25 mm/s

Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 1.5 mm
Maximum Retraction Count: 100
Minimum Extrusion Distance Window: 6,5 - 10 mm
Limit Support Retractions: Check
Combing Mode: All
Max Comb Distance With No Retract: 30 mm
Retract Before Outer Wall: Check
Avoid Printed Parts When Travelling: Check
Avoid Supports When Travelling: Check
Travel Avoid Distance: 1 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm
Z Hop When Retracted: Check
Z Hop Height: 0,3 mm

Enable Print Cooling: Check
Fan Speed: 100%
Regular Fan Speed: 100%
Maximum Fan Speed: 100% 

Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.36 mm
Regular Fan Speed at Layer: 3 

Minimum Layer Time: 10 s
Minimum Speed: 10 mm/s

Generate Support: Check
Support Structure: Normal (you can try using Tree Support Structure if you have difficulty printing any particular assembly part)
Support Placement: Everywhere 
Support Overhang Angle: 60° (this parameter can range from 30° to 70° depending on the part at hand)
Support Pattern: Zig Zag
Support Wall Line Count: 1 (stronger support that might be more difficult to remove) 0 (less strong support but is easier to remove)

Support Density: 15%
Support Line Distance: 2.6667 mm
Initial layer support line distance: 2.667 mm

Support Z Distance: 0.12 mm
Support Top Distance: 0.12 mm
Support Bottom Distance: 0.12 mm

Support X/Y Distance: 0.8-1 mm
Support Distance Priority: Z overrides X/Y
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Stair Step Minimum Slope Angle: 10°
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.2 mm
Gradual Support Infill Steps: 0
Minimum Support Area: 2 mm

Enable Support Interface: Check (generates additional “pillow” on the support structure that leads to a more even surface, but can be difficult to remove in hard-to-reach areas)
Enable Support Roof: Check
Enable Support Floor: Check

Support Interface Thickness: 0.8 mm
Support Roof Thickness: 0.8 mm
Support Floor Thickness: 0.8 mm

Support Interface Resolution 0.2 mm
Support Interface Density: 50-100%
        Support Roof Density: 50-100%
Support Roof Line Distance: 0.8 mm
        Support Floor Density: 50-100%
Support Floor line Distance:  0.4mm

Support Interface Pattern: Grid 
Support Roof Pattern: Grid (this parameter should differ from Bottom Pattern Initial Layer in “Shell” section)
Support Floor Pattern: Grid

Minimum Support Interface Area: 10mm
Minimum Support Roof Area: 10 mm
Minimum Support Floor Area: 10 mm

Support Interface Horizontal Expansion: 0.0 mm
Support Roof Horizontal Expansion: 0.0 mm
Support Floor Horizontal Expansion: 0.0 mm

Fan Speed Override: Check
Supported Skin Fan Speed: 100%
Use Towers: Check
Tower Diameter: 4 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Skirt/Brim (For unsteady parts, and those parts that may come unstuck use “Brim”. For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
       Brim Line Count: 10
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Extruder 1 Temperature: 210
Heated Bed: 60

Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
  Detect thin walls: Check
  Detect bridging perimeters: Check
  Seam position: Random
  Fill desity: 20%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
  Infill/Perimeters overlap: 20%
  Bridge flow ratio: 0.95
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm


comments powered by Disqus

Similar items

Browse more newly listed 3D printings