Make pre-order

Sylvanas 3D Printing Miniature | Assembly

cm: 19.6 w x 27 d x 47 h
in: 7.717 w x 10.63 d x 18.504 h
BUY FOR  $24.99

Source Files




Printing Details

This 3D model consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Version 1 and Version 2 are the files for Sylvanas 3D Model optimized for 3D printing, the preview pictures of which you see above.

It is recommended:

  • to print Version 1 STL files on FDM/FFF 3D printers;
  • to print Version 2 STL files on DLP/SLA/SLS 3D printers.
File Name File Size Time / Filament
14.94 MiB 20 h 11 min
13 m
10.68 MiB 4 h 1 min
2 m
10.35 MiB 4 h 5 min
2 m
5.31 MiB 3 h 28 min
2 m
0.92 MiB 27 min
<1 m
1.41 MiB 35 min
<1 m
8_Ge_lock_7S (x8).STL
0.01 MiB 3 min
<1 m
9_Ge_lock_7S_70_ (x9).STL
0.01 MiB 2 min
<1 m
6.69 MiB 3 h 8 min
2 m
11_hand_L (with_bow).STL
13.47 MiB 8 h 19 min
4 m
4.86 MiB 2 h 14 min
1 m
10.83 MiB 5 h 49 min
3 m
4.84 MiB 2 h 22 min
1 m
19.15 MiB 13 h 16 min
8 m
7.66 MiB 5 h 18 min
3 m
8.12 MiB 5 h 20 min
3 m
0.57 MiB 14 min
<1 m
0.50 MiB 12 min
<1 m
0.58 MiB 14 min
<1 m
4.81 MiB 1 h 14 min
1 m
3.85 MiB 1 h 13 min
1 m
15.46 MiB 14 h 27 min
9 m
34.09 MiB 43 h 59 min
25 m
0.00 MiB 20 min
<1 m
20.75 MiB 9 h 52 min
6 m


One day Sylvanas Windrunner was the brave leader of the pathfinders of Silvermoon and the commander of the high elfs armies. But during the Third War, Prince Arthas, at the head of the undead army, invaded the elfs kingdom of Quel'Thalas. Sylvanas spent all her energy against the army of the living dead but was eventually killed by the Death Knight and turned into an obedient Banshee slave. Cursed and devoid of free will she served her master until the Lich King was so much weak that he could no longer control her. Sylvanas and her rebels seized the Undercity, declaring themselves free and independent. Somehow she regained her physical form, but her body still carries the curse of the undead, and therefore the former life is not available to her. Now Sylvanas dreams of only one is to find and destroy Arthas. She hates him the most in the world and also she wants to destroy the Lich King in order to avenge his curse and bring final freedom to his subjects. Some people say that during the transformation into a banshee between Sylvanas and the Lich King, a certain kind of communication was established, therefore it is impossible to destroy her soul until finally, the Lich will be destroyed.


The model is saved in STL files, a format supported by most 3D printers

FDM version features:

- Contain 25 parts. One part of Lock (8_Ge_lock_7S (x8)) you need to print 8 times. One part of Lock (9_Ge_lock_7S_70_ (x9)) you need to print 9 times;
- Made with locks;
- Made with special platform with huge banner;
- Made with 2 versions of quiver. With arrows and without them. Parts of arrows you can print separately;
- All parts are divided in such way that you will print them with the smallest amount of supports.

SLS/SLA version features:

- Same as FDM but smaller and made as 4 parts.

All STL files for 3D printing have been checked in Netfabb and no errors were shown.

Note: Before starting 3D printing the model, read the Printing Details for CURA 3.1.0. Software.

There are 25 parts for FFF/FDM version and 4 parts for SLS/SLA version.

Scale: Her tall in life is 2130 mm. Model made as 1/8 scale in FDM version and 1/16 in SLS/SLA version.

FDM version dimensions:

After being printed will stand - 470 mm tall, 196 mm wide, 270 mm deep;

SLS/SLA version dimensions:

After being printed will stand - 235 mm tall, 98 mm wide, 135 mm deep;

- Have few details, to keep printing costs down.


- STL files of Sylvanas for 3D printing which consist of 29 parts;

- 2 versions of files for this model for FFF/FDM and SLS/SLA;

- Made with special platform with huge banner. Made with 2 versions of quiver. With arrows and without them;

- Made with locks for better fixing in FDM version;

- High-poly detailed model of Sylvanas;

- Detailed settings that we provide for Cura 3.1.0. for the best print;

- Full technical support from the Gambody Support Team.

Watch the tutorial video on how to assemble Sylvanas 3D Printing Miniature at Gambody YouTube channel.  

You can get Model of Sylvanas for 3D Printing right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Also, you may like another Warcraft 3D models.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.1.0. and printed on an Ultimaker 2 in PLA material.

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

To avoid printing problems, we recommend the following settings:


Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Slicing Tolerance: Middle
Line Width: 0.4 mm
Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
   Top/Bottom Line Width: 0.4 mm
   Infill Line Width: 0.4 mm
   Skirt/Brim Line Width: 0.4 mm
   Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%


Wall Thickness: 0.8 mm
Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1


Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0


Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 


Print Speed: 45 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s
      Support Infill Speed: 45 mm/s
Travel Speed: 80 mm/s
Initial Layer Speed: 15 mm/s

    Initial Layer Print Speed: 15 mm/s
    Initial Layer Travel Speed: 26.6667 mm/s
Skirt/Brim Speed: 15 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2


Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm 
Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s


Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 1.3333 mm
Support Z Distance: 0.3 mm
    Support Top Distance: 0.3 mm
    Support Bottom Distance: 0.3 mm
Support X/Y Distance: 0.7 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.2 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 

Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 18 
Brim Only on Outside: Check

Mesh Fixes 

Union Overlapping Volumes: Check
Maximum Resolution: 0.01 mm
Merged Meshes Overlap: 0.15 mm

Special Modes

Print Sequence: All at Once
Surface Mode: Normal

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.


comments powered by Disqus
Other author's 3D printings


Warcraft, Elf, Sylvanas, heroes, Assembly, warrior, game

Similar items

Browse more newly listed 3D printings