Make pre-order

B1 Battle Droid 3D Printing Model | Assembly + Action

average
cm: 6.2 w x 7.8 d x 24.8 h
in: 2.441 w x 3.071 d x 9.764 h
6
BUY FOR  $24.99

Source Files

|

Description

|

Printing Details

This 3D Model consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

B1 Battle Droid 3D Printing Model comes in 3 versions for FFF/FDM, DLP/SLA and SLS 3D printers. Files for each version are available for download after purchase.

Detailed information about this 3D printing model is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
1_foot_R_FDM (repaired).s tl
4.53 MiB 31 min
<1 m
11 x 33 x 20 Download
2_foot_L_FDM (repaired).s tl
4.53 MiB 32 min
<1 m
11 x 33 x 20 Download
3_shin_R_FDM (repaired).s tl
5.91 MiB 1 h 16 min
<1 m
11 x 13 x 68 Download
4_shin_L_FDM (repaired).s tl
5.92 MiB 1 h 15 min
1 m
11 x 13 x 68 Download
5_leg_R_FDM (repaired).st l
6.90 MiB 1 h 15 min
1 m
13 x 14 x 61 Download
6_leg_L_FDM (repaired).st l
6.90 MiB 1 h 14 min
1 m
13 x 14 x 61 Download
7_connector_leg_R_FDM (re paired).stl
0.08 MiB 4 min
<1 m
15 x 4 x 4 Download
8_connector_leg_L_FDM (re paired).stl
0.08 MiB 4 min
<1 m
15 x 4 x 4 Download
9_pelvis_FDM (repaired).s tl
17.83 MiB 1 h 47 min
1 m
20 x 34 x 41 Download
10_piston_in_R_FDM (repai red).stl
1.00 MiB 5 min
<1 m
11 x 20 x 4 Download
11_piston_out_R_FDM (repa ired).stl
1.29 MiB 15 min
<1 m
14 x 7 x 15 Download
12_piston_in_L_FDM (repai red).stl
1.00 MiB 5 min
<1 m
10 x 20 x 4 Download
13_piston_out_L_FDM (repa ired).stl
1.29 MiB 15 min
<1 m
14 x 7 x 15 Download
14_body_joint_FDM (repair ed).stl
0.30 MiB 20 min
<1 m
10 x 10 x 20 Download
15_body_claw_FDM (repaire d).stl
0.16 MiB 8 min
<1 m
14 x 15 x 6 Download
16_body_FDM (repaired).st l
13.66 MiB 2 h 55 min
2 m
Download
17_neck_FDM (repaired).st l
0.46 MiB 26 min
<1 m
24 x 40 x 11 Download
18_head_1_FDM (repaired). stl
9.49 MiB 1 h 5 min
1 m
Download
19_head_2_FDM (repaired). stl
2.68 MiB n.a.
n.a.
14 x 13 x 19 Download
20_anten_FDM (repaired).s tl
0.81 MiB 13 min
<1 m
Download
21_backpack_FDM (repaired ).stl
9.67 MiB 1 h 55 min
1 m
Download
22_backpack_anten_1_FDM ( repaired).stl
0.18 MiB 4 min
<1 m
2 x 49 x 2 Download
23_backpack_anten_2_FDM ( repaired).stl
0.16 MiB 3 min
<1 m
2 x 40 x 2 Download
24_shoulder_1_R_FDM (repa ired).stl
0.52 MiB 25 min
<1 m
17 x 17 x 18 Download
25_shoulder_2_R_FDM (repa ired).stl
0.42 MiB 14 min
<1 m
Download
26_shoulder_1_L_FDM (repa ired).stl
0.52 MiB 25 min
<1 m
Download
27_shoulder_2_L_FDM (repa ired).stl
0.42 MiB 14 min
<1 m
Download
28_arm_R_FDM (repaired).s tl
1.61 MiB 18 min
<1 m
Download
29_arm_L_FDM (repaired).s tl
1.61 MiB 18 min
<1 m
Download
30_hand_R_FDM (repaired). stl
0.55 MiB 14 min
<1 m
Download
31_hand_L_FDM (repaired). stl
0.55 MiB 14 min
<1 m
Download
32_wrist_R_FDM (repaired) .stl
1.51 MiB 12 min
<1 m
Download
33_wrist_L_FDM (repaired) .stl
1.51 MiB 12 min
<1 m
Download
34_finger_a_R_FDM (repair ed).stl
0.12 MiB 8 min
<1 m
Download
35_finger_b_R_FDM (repair ed).stl
0.04 MiB 2 min
<1 m
4 x 11 x 3 Download
36_finger_c_R_FDM (repair ed).stl
0.04 MiB n.a.
n.a.
4 x 11 x 3 Download
37_finger_d_R_FDM (repair ed).stl
0.09 MiB 2 min
<1 m
Download
38_finger_e_R_FDM (repair ed).stl
0.05 MiB n.a.
n.a.
8 x 4 x 3 Download
39_finger_a_L_FDM (repair ed).stl
0.12 MiB 8 min
<1 m
Download
40_finger_b_L_FDM (repair ed).stl
0.04 MiB 2 min
<1 m
4 x 11 x 3 Download
41_finger_c_L_FDM (repair ed).stl
0.04 MiB 2 min
<1 m
Download
42_finger_d_L_FDM (repair ed).stl
0.09 MiB 2 min
<1 m
Download
43_finger_e_L_FDM (repair ed).stl
0.05 MiB 2 min
<1 m
Download
44_E_5_blaster_rifle_FDM (repaired).stl
4.61 MiB 1 h 25 min
1 m
Download
45_body_cap_FDM (repaired ).stl
0.27 MiB 10 min
<1 m
15 x 19 x 4 Download
Keychain (repaired).stl
0.35 MiB 23 min
<1 m
30 x 30 x 2 Download
Tag (repaired).stl
1.70 MiB 1 h 16 min
1 m
Download

ABOUT THIS 3D MODEL

"Roger, roger."

B1 Battle Droid, also known as Standard Battle Droid or simply Clanker, is a crucial member of the Separatist/CIS army and a brilliant comic relief of the Star Wars prequel trilogy. Designed to resemble their Geonosian creators, Battle Droids proved to be absolutely ineffective alone but could be deadly in large numbers. The humanoid robots are dim-witted, extremely fragile, and have little tactical intelligence but are very cheap to produce so the decision was reached to create millions of droid copies to overwhelm the enemy not in power but through sheer numbers. Our contributing 3D artist was taken by the idea of creating the backbone of the Confederate fighting force for 3D printing and spent 95 hours working on a B1 Battle Droid model. The Clanker for 3D printing has the unit’s trademark elongated face and a pair of specialized movement processors in the back of the head. The author of the model made sure to equip the Droid with the unit’s standardized E-5 blaster rifle and a backpack device that is known to be needed for power augmentation in order for the droids to operate in the field without recharge for a longer period of time. There is also a pair of long signal reception booster antennas extending from the backpack of a 3D printing robot that can be optionally displayed alone on the droid’s back. B1 Battle Droids might be the easily controlled mindless soldiers but some personality quirks revealed by “programming glitches” made the unit well-loved among Star Wars fans. 3D print your own Droid legion - the STL files are waiting for you to download!

ADAPTATION FOR 3D PRINTING

B1 Battle Droid model for 3D printing is a highly articulated assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 39 hours in total. In order to ensure the robot’s multidirectional movement, it was divided into many assembly parts and special mechanisms were introduced into all model’s joints to give you an opportunity to display B1 Battle Droid in a variety of positions, i.e. droid’s head, neck, shoulder, elbow, wrist, finger, hip, knee and ankle are movable and the droid’s pelvis is equipped with the ball-and-claw joint. For the articulated robot to stand firm in any position you may choose, most of the joints are provided with locking mechanisms. Droid’s back can be optionally displayed with antennas or backpack+antennas and the E-5 blaster rifle can be placed into Droid’s hands as you prefer by folding the fingers. All assembly parts are provided in STL files in recommended positions that were worked out in order to ensure the smoothness of the details’ surfaces after printing and so that the 3D printing beginners won't face difficulties when placing the parts on a build plate. The model’s assembly in FFF/FDM 1.0 version requires additional “pins” to secure the parts. These pins do not come in STL files but can be made out of short pieces of regular 1.75 PLA. We highly recommend that you watch "Assembly video" in the photo preview section before assembling the Droid. When downloading any model's file you will also receive "Assembly Manual" for FFF/FDM 1.0 and DLP/SLA 1.0 versions in PDF format.

The model is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from B1 Battle Droid​​​'s actual height that is 1930 mm. The 3D printing model's chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS versions.

VERSION SPECIFICATIONS

FFF/FDM 1.0 version features:
- Contains 45 parts;
- A printed model is 248 mm tall, 62 mm wide, 78 mm deep;
- Each robot’s joint (head, neck, shoulder, elbow, wrist, finger, pelvis, hip, kneeankle) is articulated which allows the model's multidirectional movement;
- This version's assembly requires additional “pins” to secure the parts. These pins do not come in STL files but can be made out of short pieces of regular 1.75 PLA;
- Droid’s back can be optionally displayed with antennas or backpack+antennas;
- You can put the E-5 blaster rifle into Droid’s hands as you prefer by folding the fingers;
- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:
- Contains 12 parts;
- A printed model is 124 mm tall, 31 mm wide, 39 mm deep;
- Comprises parts for you to assemble Droid either in an action pose or in a static pose holding an E-5 blaster rifle;
- Can be displayed with or without backpack+antennas;
- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

SLS 1.0 version features:
- Made as a solid one-piece figurine;
- A printed model is 124 mm tall, 31 mm wide, 39 mm deep;
- Contains 4 parts - solid models in an action pose with and without backpack+antennas; solid models in a static pose holding an E-5 blaster rifle with and without backpack+antennas.

WHAT WILL YOU GET AFTER PURCHASE?

- STL files of B1 Battle Droid​​​ Model for 3D printing which consist of 61 parts;
3 versions of files for this model for FFF/FDM, DLP/SLA and SLS;
- High-poly detailed model of B1 Battle Droid​​​;
Assembly Manual for FFF/FDM 1.0 and DLP/SLA 1.0 versions in PDF format;
- Detailed settings that we provide as a recommendation for Cura 3.5.1, Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get the model of B1 Battle Droid​​​​ for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble B1 Battle Droid​​​ 3D Printing Model at Gambody YouTube channel.

Also, you may like other Space War Online 3D Printing Figurines as well as other Droid 3D Printing Models.

_______
FAQ: 

Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.4.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for CuraSimplify3D and Slic3r softwares.

Cura printing recommendations:

To avoid printing problems, we recommend the following settings:

Quality
Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Shell
Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill
Infill Density: 80%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Material
Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s

Speed 
Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
Travel Speed: 45 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 30 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Travel 
Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Cooling 
Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100%
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Support 
Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 50°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 3 mm
Support Z Distance: 0.1 mm
    Support Top Distance: 0.1 mm
    Support Bottom Distance: 0.1 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65°

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 18
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Experimental
Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Extruder
Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Layer
Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Additions
Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Infill
Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 80%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Support
Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Temperature
Extruder 1 Temperature: 210
Heated Bed: 60

Cooling
Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Speeds
Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Other
Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
Quality
  Detect thin walls: Check
  Detect bridging perimeters: Check
Advanced
  Seam position: Random
Infill
  Fill density: 80%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
Advanced
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
Skirt
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
Brim 
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
Raft
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
Modifiers
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
Autospeed
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
Overlap
  Infill/Perimeters overlap: 20%
Flow
  Bridge flow ratio: 0.95
Other
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm

Comments

comments powered by Disqus

Similar items

Browse more newly listed 3D printings