Make pre-order

Michael Myers 3D Printing Figurine | Assembly

cm: 25.7 w x 25.2 d x 28.7 h
in: 10.118 w x 9.921 d x 11.299 h
BUY FOR  $24.99

Source Files




Printing Details

This 3D Figurine consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Michael Myers 3D Printing Figurine comes in 4 versions for each 3D printer type (FFF/FDM, DLP/SLA and SLS). Files for each version are available for download after the purchase.

Detailed information about this 3D printing figurine is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
24.99 MiB 2 h 27 min
1 m
28 x 36 x 44 Download
24.65 MiB 8 h 44 min
5 m
61 x 49 x 72 Download
24.51 MiB 14 h 50 min
8 m
71 x 65 x 145 Download
14.35 MiB 1 h 49 min
1 m
24 x 24 x 70 Download
5_hand_L_FDM(repaired).st l
8.96 MiB 26 min
<1 m
17 x 14 x 24 Download
6_arm_R_1_FDM(repaired).s tl
13.05 MiB 1 h 1 min
1 m
28 x 26 x 33 Download
7_arm_R_2_FDM(repaired).s tl
8.25 MiB 49 min
<1 m
25 x 23 x 29 Download
8_hand_R_FDM(repaired).st l
10.33 MiB 30 min
<1 m
14 x 17 x 25 Download
10.73 MiB 9 min
<1 m
4 x 49 x 8 Download
10_leg_L_FDM(repaired).st l
12.54 MiB 52 min
<1 m
27 x 39 x 18 Download
11_leg_R_FDM(repaired).st l
12.54 MiB 52 min
<1 m
26 x 40 x 18 Download
12_halloween_pumpkin_FDM( repaired).stl
13.36 MiB 8 h 43 min
6 m
64 x 63 x 55 Download
13_plank_1_FDM(repaired). stl
11.39 MiB 3 h 55 min
2 m
137 x 36 x 7 Download
14_plank_2_FDM(repaired). stl
5.80 MiB 2 h 36 min
1 m
139 x 26 x 6 Download
15_plank_3_FDM(repaired). stl
5.81 MiB 2 h 33 min
1 m
139 x 26 x 6 Download
16_plank_4_FDM(repaired). stl
8.43 MiB 56 min
<1 m
11 x 4 x 93 Download
17_plank_5_FDM(repaired). stl
7.99 MiB 56 min
<1 m
11 x 4 x 93 Download
18_stair_rails_1_FDM(repa ired).stl
19.53 MiB 8 h 13 min
4 m
25 x 118 x 99 Download
19_stair_rails_2_FDM(repa ired).stl
19.73 MiB 8 h 28 min
4 m
25 x 118 x 99 Download
20_flooring_1_FDM(repaire d).stl
14.50 MiB 11 h 30 min
6 m
101 x 125 x 16 Download
21_flooring_2_FDM(repaire d).stl
15.38 MiB 9 h 45 min
5 m
85 x 126 x 16 Download
22_platform_1_FDM(repaire d).stl
15.01 MiB 20 h 56 min
11 m
127 x 126 x 41 Download
23_platform_2_FDM(repaire d).stl
13.90 MiB 20 h 11 min
11 m
127 x 125 x 41 Download
24_platform_3_FDM(repaire d).stl
16.23 MiB 30 h 30 min
18 m
125 x 126 x 45 Download
25_platform_4_FDM(repaire d).stl
15.21 MiB 29 h 37 min
17 m
125 x 126 x 45 Download
26_ge_lock_7S(x1)_FDM(rep aired).stl
0.02 MiB 3 min
<1 m
7 x 18 x 2 Download
27_ge_lock_10H(x20)_FDM(r epaired).stl
0.03 MiB 4 min
<1 m
18 x 10 x 2 Download
Keychain (repaired).stl
0.35 MiB 23 min
<1 m
30 x 30 x 2 Download
Tag (repaired).stl
1.70 MiB 1 h 16 min
1 m
150 x 18 x 5 Download
12_halloween_pumpkin_p1_F DM(repaired).stl
15.02 MiB 6 h 47 min
4 m
64 x 63 x 39 Download
12_halloween_pumpkin_p2_F DM(repaired).stl
6.80 MiB 56 min
1 m
35 x 37 x 22 Download
1_head_v2_FDM(repaired).s tl
27.26 MiB 2 h 54 min
1 m
25 x 35 x 44 Download


Michael Myers is the iconic slasher character from the Halloween films series. The horror classic that is considered to have jump-started the slasher genre popularity has been successfully keeping in awe film-goers since 1978 and now all 3D printing enthusiasts have an awesome opportunity to place a legendary 3D printed serial killer on a shelf. A young boy who ruthlessly murdered his sister returns to his hometown from asylum 15 years later to hunt down the rest of his family to kill them and later wanders around town scoping out victims and targeting teenage babysitters. The author of this 3D printing figurine spent 142 hours to depict the serial killer with the blackest eyes... the devil's eyes. Michael Myers for 3D printing stands on the wooden porch of his house in Haddonfield with his hand holding a simple kitchen knife raised. The pumpkin that lies near the stairs indicates that the scene takes place on Halloween night and the Shape is ready to stalk the babysitters of the neighbourhood. The model is portrayed wearing a mechanic jumpsuit, work boots and Myers’ trademark expressionless Halloween mask that hides his face and terrifies the killer’s victims. Michael Myers 3D printing figurine will definitely become a menacing addition to any collection of horror classic characters, hurry up to print!


Michael Myers figurine for 3D printing is a static assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 36 hours in total. Figurine’s anatomy was thoroughly reviewed during the moderation process for the slasher films legend to be depicted harmoniously in the intended malicious pose. The model’s cutting was chosen by our team to minimise the amount of filament needed for generated support and some of the parts were hollowed out for you to save resin in the figurine’s Eco version. For you to receive the cleanest result possible the knife that Myers is holding up was extracted from the raised hand and in order to conceal the places where the assembly parts of the model must be connected, the figurine was cut along the contour of Michael Myers clothes’ seams. What is more, to ensure an excellent quality of the 3D printed result, the platform was also divided into many assembly pieces, i.e. each tread is provided separately, as well as balusters and holiday pumpkin. All the assembly parts are provided in STL files in recommended positions that were worked out so to ensure the smoothness of the details’ surfaces after printing and that the 3D printing beginners won't face difficulties when placing the parts on a build plate.

The figurine is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from Michael Myers' actual height that is 1900 mm. The 3D printing figurine's chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS versions.


FFF/FDM 1.0 version features:
- Contains 27 parts;
- A printed model is 287 mm tall, 257 mm wide, 252 mm deep;
- Assembly kit includes locks to connect parts securely without glue. One lock 26_ge_lock_7S(x1) to attach the figurine's body to legs securely without glue needs to be printed once; another lock 27_ge_lock_10H(x20) needs to be printed 20 times;
- Made with a platform to resemble the wooden doorstep of the Michael Myers' house in Haddonfield on Halloween;
- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:
- Contains 8 parts;
- A printed model is 144 mm tall, 129 mm wide, 126 mm deep;
- Made with a platform to resemble the wooden doorstep of the Michael Myers' house in Haddonfield on Halloween;
- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

DLP/SLA Eco 1.0 version features:
- Contains 8 parts;
- A printed model is 144 mm tall, 129 mm wide, 126 mm deep;
- Made with a platform to resemble the wooden doorstep of the Michael Myers' house in Haddonfield on Halloween;
- Contains some hollowed out parts to save resin.

SLS 1.0 version features:
- Made as a solid one-piece figurine;
- A printed model is 144 mm tall, 129 mm wide, 126 mm deep;
- Contains 3 parts - a one-piece model and Leatherface with the platform separated.


- STL files of Michael Myers 3D Figurine for 3D printing which consist of 46 parts;
- 4 versions of files for this model for FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS;
- High-poly detailed figurine of Michael Myers;
- Detailed settings that we provide as a recommendation for Cura 3.5.1, Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get the figurine of Michael Myers​ for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Michael Myers​ 3D Printing Figurine at Gambody YouTube channel.

Also, you may like other Villain 3D Printing Figurines.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.5.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for CuraSimplify3D and Slic3r softwares.

Cura printing recommendations:

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

To avoid printing problems, we recommend the following settings:

Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s 
     Support Infill Speed: 45 mm/s
Travel Speed: 45 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 45 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.6562 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 2.2 mm
Support Z Distance: 0.13 mm
    Support Top Distance: 0.13 mm
    Support Bottom Distance: 0.13 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 15 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Extruder 1 Temperature: 210
Heated Bed: 60

Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
  Detect thin walls: Check
  Detect bridging perimeters: Check
  Seam position: Random
  Fill desity: 20%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
  Infill/Perimeters overlap: 20%
  Bridge flow ratio: 0.95
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm


comments powered by Disqus

Similar items

Browse more newly listed 3D printings