Make pre-order

Queen of Blades 3D Printing Miniature | Assembly

cm: 24 w x 28.5 d x 36.5 h
in: 9.449 w x 11.22 d x 14.37 h

Source Files




Printing Details

This 3D model consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Version 1 and Version 2 are the files for Queen of Blades 3D Model optimized for 3D printing, the preview pictures of which you see above.

It is recommended:

  • to print Version 1 STL files on FDM/FFF 3D printers;
  • to print Version 2 STL files on DLP/SLA/SLS 3D printers.
File Name File Size Time / Filament Object Size
(x/y/z mm)
15.74 MiB 17 h 13 min
10 m
195 x 179 x 144 Download
15.33 MiB 14 h 18 min
8 m
202 x 164 x 160 Download
17.94 MiB 15 h 26 min
9 m
67 x 47 x 127 Download
4_GE_Connector_A_A (x4).S TL
0.03 MiB 6 min
<1 m
15 x 5 x 5 Download
2.20 MiB 1 h 47 min
1 m
18 x 21 x 88 Download
2.21 MiB 1 h 46 min
1 m
16 x 40 x 75 Download
5.03 MiB 3 h 36 min
2 m
35 x 63 x 66 Download
5.10 MiB 3 h 14 min
2 m
32 x 36 x 94 Download
3.59 MiB 2 h 8 min
1 m
21 x 26 x 88 Download
3.66 MiB 2 h 6 min
1 m
22 x 26 x 87 Download
11_GE_Connector_B_C (x8). STL
0.05 MiB 9 min
<1 m
25 x 6 x 6 Download
12_GE_Connector_platform (x2).STL
0.04 MiB 19 min
<1 m
9 x 29 x 9 Download
26.30 MiB 25 h 44 min
19 m
161 x 193 x 41 Download
28.14 MiB 32 h 5 min
25 m
210 x 155 x 41 Download
9.04 MiB 46 h
40 m
114 x 149 x 111 Download
9.29 MiB 39 h 41 min
31 m
178 x 88 x 111 Download
8.68 MiB 63 h 14 min
56 m
164 x 152 x 111 Download
14.22 MiB 77 h 44 min
68 m
167 x 235 x 111 Download


Sarah Kerrigan is psionic from a squad of ghosts. The ghosts are left her die of the Zergs, but instead of killing Zergs are captured her. She was put in a cocoon and turned into her Queen. This was done in order to get rid of the power of Amon. But in the end, she also killed him and became a new Zel-naga. Whan Sarah turning into a Queen of Blades, this made her much stronger. Kerrigan became aggressive, her enjoyment of the fight is very great. She tears her opponents with wings and cut by claws. Because of her extremely high psi-potential, Kerrigan was used as a child by the military Terran Confederacy in a program to study psi-abilities. Severe grueling training and the use of neuroimplants to control her abilities made her a closed and unsociable woman. Despite this, Kerrigan has repeatedly proved that she is a brave soldier and an experienced tactician. She negatively treated the tactics of using zerg against the forces of the Confederation. However, after rebirth, Kerrigan is freed from any moral prohibitions as well as from psychological barriers laid by Confederate scientists. The dark essence of her soul breaks loose.


Queen of Blades 3D model for printing was created in ZBrush. The model is saved in STL files, a format supported by most 3D printers

FDM version features:

- Contain 18 parts;

- Made with 3 type of connectors. (4_GE_Connector_A_A (x4)) you need to print 4 times. (11_GE_Connector_B_C (x8)) you need to print 8 times. (12_GE_Connector_platform (x2)) you need to print twice;

- Made with platform that stylized under Terran ruins;

- You can print only top plate of platform for good standing on surface;

- All parts are divided in such way that you will print them with the smallest amount of supports.

SLS/SLA version features:

- Same as FDM but smaller and made as 3 parts.

All .STL files for 3D printing have been checked in Netfabb and no errors were shown.

Note: Before starting 3D printing the model, read the Printing Details for CURA 3.1.0. Software.

There are 18 parts for FFF/FDM version and 3 parts for SLS/SLA version.

All parts of connectors should be printed at 100% infill.

Scale: Her tall in life is 1950 mm. Model made as 1/8 scale in FDM version and 1/16 in SLS/SLA version.

FDM version dimensions:
After being printed will stand - 475 mm tall, 330 mm wide, 326 mm deep - with full platform;
365 mm tall, 240 mm wide, 285 mm deep - with top plate;
- Connectors should be printed at 100% infill to make them solid.
SLS/SLA version dimensions:
After being printed will stand - 237 mm tall, 165 mm wide, 163 mm deep - with full platform;
182 mm tall, 120 mm wide, 142 mm deep - with top plate;
- Has only 3 details, to keep printing costs down.


- .STL files of Queen of Blades for 3D printing which consist of 21 parts;

- 2 versions of files for this model for FFF/FDM and SLS/SLA;

- Gorgeous platform that stylized under Terran ruins;
- Available in economy variant with small platform;

- High-poly detailed model of Queen of Blades;

- Detailed settings that we provide for Cura 3.1.0. for the best print;

- Full technical support from the Gambody Support Team.

Watch the tutorial video on how to assemble Queen of Blades 3D Printing Miniature at Gambody YouTube channel.  

You can get Queen of Blades model for 3D Printing right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Also you can get more SpaceCraft models and collect your universe of this game.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?


This model was tested in Cura 3.1.0. and printed on an Ultimaker 2 in PLA material.

Note: All parts of connectors should be printed at 100% infill.

To avoid printing problems, we recommend the following settings:


Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Slicing Tolerance: Middle
Line Width: 0.4 mm
Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
   Top/Bottom Line Width: 0.4 mm
   Infill Line Width: 0.4 mm
   Skirt/Brim Line Width: 0.4 mm
   Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%


Wall Thickness: 0.8 mm
Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1


Infill Density: 20% (all parts of the connectors should be printed at 100% infill)
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0


Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 


Print Speed: 45 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s
      Support Infill Speed: 45 mm/s
Travel Speed: 80 mm/s
Initial Layer Speed: 15 mm/s

    Initial Layer Print Speed: 15 mm/s
    Initial Layer Travel Speed: 26.6667 mm/s
Skirt/Brim Speed: 15 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2


Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm 
Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s


Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 1.3333 mm
Support Z Distance: 0.3 mm
    Support Top Distance: 0.3 mm
    Support Bottom Distance: 0.3 mm
Support X/Y Distance: 0.7 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.2 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 

Build Plate Adhesion Type: Brim
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 18 
Brim Only on Outside: Check

Mesh Fixes 

Union Overlapping Volumes: Check
Maximum Resolution: 0.01 mm
Merged Meshes Overlap: 0.15 mm

Special Modes

Print Sequence: All at Once
Surface Mode: Normal

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.


comments powered by Disqus

Similar items

Browse more newly listed 3D printings