Make pre-order

Ultralisk 3D Printing Figurine | Assembly

cm: 28.8 w x 34.5 d x 27.7 h
in: 11.339 w x 13.583 d x 10.906 h
BUY FOR  $26.99

Source Files




Printing Details

This 3D Figurine consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Ultralisk 3D Printing Figurine comes in 6 versions for each 3D printer type (FFF/FDM, DLP/SLA, and SLS). Files for each version are available for download after the purchase.

Detailed information about this model is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
9.55 MiB 13 h 16 min
9 m
99 x 86 x 67 Download
14.28 MiB 31 h 9 min
23 m
165 x 90 x 103 Download
18.06 MiB 40 h 49 min
26 m
201 x 77 x 152 Download
0.04 MiB 8 min
<1 m
7 x 20 x 6 Download
0.04 MiB 8 min
<1 m
7 x 20 x 6 Download
0.04 MiB 8 min
<1 m
6 x 20 x 6 Download
0.04 MiB 8 min
<1 m
6 x 20 x 6 Download
0.04 MiB 8 min
<1 m
6 x 20 x 6 Download
5.37 MiB 4 h 55 min
3 m
60 x 47 x 67 Download
0.04 MiB 8 min
<1 m
6 x 20 x 6 Download
19.86 MiB 37 h 4 min
23 m
79 x 115 x 136 Download
32.42 MiB 40 h 8 min
25 m
87 x 135 x 127 Download
0.04 MiB 14 min
<1 m
8 x 30 x 7 Download
0.04 MiB 14 min
<1 m
8 x 30 x 7 Download
0.04 MiB 14 min
<1 m
8 x 30 x 7 Download
0.04 MiB 8 min
<1 m
7 x 20 x 6 Download
0.04 MiB 8 min
<1 m
7 x 20 x 6 Download
0.04 MiB 8 min
<1 m
6 x 20 x 6 Download
0.04 MiB 8 min
<1 m
6 x 20 x 6 Download
8.14 MiB 11 h 33 min
7 m
49 x 61 x 130 Download
6.01 MiB 7 h 60 min
5 m
48 x 63 x 105 Download
4.72 MiB 3 h 33 min
2 m
56 x 59 x 25 Download
5.85 MiB 6 h 41 min
5 m
56 x 78 x 37 Download
0.04 MiB 14 min
<1 m
8 x 30 x 7 Download
0.04 MiB 8 min
<1 m
6 x 20 x 6 Download
1.55 MiB 3 h 30 min
2 m
24 x 138 x 76 Download
5.66 MiB 15 h 45 min
9 m
48 x 223 x 107 Download
0.04 MiB 8 min
<1 m
6 x 20 x 6 Download
0.04 MiB 8 min
<1 m
7 x 20 x 6 Download
0.04 MiB 8 min
<1 m
7 x 20 x 6 Download
0.04 MiB 8 min
<1 m
7 x 20 x 6 Download
0.04 MiB 8 min
<1 m
6 x 20 x 6 Download
0.04 MiB 14 min
<1 m
8 x 30 x 7 Download
8.19 MiB 12 h 22 min
8 m
50 x 91 x 110 Download
4.67 MiB 7 h 11 min
4 m
50 x 67 x 96 Download
4.76 MiB 3 h 35 min
2 m
57 x 60 x 23 Download
6.18 MiB 7 h 44 min
5 m
57 x 75 x 47 Download
1.54 MiB 3 h 16 min
2 m
22 x 133 x 81 Download
5.62 MiB 15 h 33 min
9 m
47 x 224 x 115 Download
0.04 MiB 8 min
<1 m
6 x 20 x 6 Download
0.04 MiB 8 min
<1 m
7 x 20 x 6 Download
45.06 MiB 77 h 14 min
48 m
233 x 229 x 48 Download
32.25 MiB 56 h 38 min
35 m
221 x 146 x 48 Download
13.42 MiB 22 h 1 min
14 m
216 x 108 x 23 Download
0.04 MiB 14 min
<1 m
7 x 30 x 7 Download
0.04 MiB 14 min
<1 m
7 x 30 x 7 Download
42_platform_v2_full (repa ired).stl
27.68 MiB n.a.
233 x 229 x 48 Download
43_platform_v2_part_1 (re paired).stl
21.68 MiB n.a.
221 x 146 x 48 Download
44_platform_v2_part_2 (re paired).stl
8.30 MiB 17 h 8 min
9 m
216 x 108 x 23 Download
47_Ge_lock_10H_x5 (repair ed).stl
0.03 MiB 4 min
<1 m
10 x 18 x 2 Download


The Ultralisk is a highly efficient and extremely dangerous unit of the Zerg race. “The hulking monstrosity on the ground” is most known for its nearly indestructible Kaiser Blades - two pairs of scythes that easily slice through most even armour-clad substances. Ultralisks possess extremely thick carapace and it even may seem that the creatures do not have any soft spots. Thanks to the talented author of the 3D printing model now Gambody’s swarm also features its deadly Ultralisk. The figurine is presented in all of the creature’s “siegebreaker” glory as it was placed by the 3D artist on a platform that has the remains of the defeated Siege Tank in it. Ultralisk figurine for 3D printing is clearly ready to destroy enemies of all units on the battlefield with its mouth open and all four kaiser blades raised for an attack. While working on the figurine’s design, the 3D artist made sure to pay attention to every single spike on the Ultralisk’s back and did his best to depict the extremely resistant chitinous plating of the creature. Ultralisk is scary, powerful and, as often mentioned by StarCraft players, rather difficult to obtain. On Gambody marketplace getting hold of the Ultralisk figurine for 3D printing is as easy as pie - just place an order for STL files and print the model that will leave no StarCraft fan indifferent.


Ultralisk figurine for 3D printing is a static assembly model and its updating and adaptation for different types of 3D printers took Gambody team 56 hours in total. For all the StarCraft fans to print the cleanest figurine possible the model’s cutting was completely revised, the figurine was divided into assembly parts anew and adapted for different types of 3D printers taking into account the present-day technology advancements. The body proportions of Ultralisk, as well as its level of detail, were thoroughly reviewed during the moderation process for the Zerg to be depicted harmoniously in the intended victorious pose. The model’s cutting was chosen by our team to minimise the amount of filament needed for generated support and some of the parts were hollowed out for you in the model’s Eco version to save resin. In order to ensure the smooth 3D printed result, all Ultralisk’s kaiser blades, dorsal spikes, fangs, horn etc. are now available as separate STL files. All the assembly parts are provided in STL files in recommended positions that were worked out so to ensure the smoothness of the details’ surfaces after printing and that the 3D printing beginners won't face difficulties when placing the parts on a build plate.

The figurine is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from Ultralisk's actual height that is 15200 mm. The 3D printing figurine's chosen scale is 1/60 for the FFF/FDM version and 1/100 for the DLP/SLA/SLS versions.


FFF/FDM 1.0 version features:
- Contains 46 parts;
- A printed model is 277 mm tall, 288 mm wide, 345 mm deep;
- Assembly kit includes two types of connectors GE_Connector_A and GE_Connector_B;
- Made with a platform to resemble a defeated Siege Tank;

FFF/FDM 2.0 version features:
- Contains 47 parts;
- A printed model is 277 mm tall, 288 mm wide, 345 mm deep;
- Assembly kit includes locks to connect parts securely without glue. Lock 46_ge_lock_7S(x11) needs to be printed 11 times and lock 47_ge_lock_10H(x12)​​ need to be printed 12 times;
- Introduced new cutting and significantly enhanced level of detail;
- Made with a platform to resemble a defeated Siege Tank;
- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:
- Contains 12 parts;
- A printed model is 139 mm tall, 144 mm wide, 173 mm deep;
- Made with a platform to resemble a defeated Siege Tank;
- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

DLP/SLA Eco 1.0 version features:
- Contains 12 parts;
- A printed model is 139 mm tall, 144 mm wide, 173 mm deep;
- Made with a platform to resemble a defeated Siege Tank;
- Contains some hollowed out parts to save resin.

SLS 1.0 version features:
- Contains 1 part;
- A printed model is 157 mm tall, 164 mm wide, 196 mm deep;

SLS 2.0 version features:
- Made as a solid one-piece figurine;
- A printed model is 139 mm tall, 144 mm wide, 173 mm deep;
- Introduced new cutting and significantly enhanced level of detail;
- Contains 3 parts - a one-piece model and a figurine with the platform separated.


- STL files of Ultralisk​ 3D Figurine for 3D printing which consist of 74 parts;
- 6 versions of files for this model for FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS;
- High-poly detailed figurine of Ultralisk;
- Detailed settings that we provide as a recommendation for Cura 3.5.1, Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get the figurine of Ultralisk​ for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Ultralisk​ 3D Printing Figurine at Gambody YouTube channel.

Also, you may like Hydralisk 3D Printing Figurine as well as other StarCraft 3D Printing Models.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.5.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for CuraSimplify3D and Slic3r softwares.

Cura printing recommendations:

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

To avoid printing problems, we recommend the following settings:

Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s 
     Support Infill Speed: 45 mm/s
Travel Speed: 45 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 45 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.6562 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 2.2 mm
Support Z Distance: 0.13 mm
    Support Top Distance: 0.13 mm
    Support Bottom Distance: 0.13 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 15 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Extruder 1 Temperature: 210
Heated Bed: 60

Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
  Detect thin walls: Check
  Detect bridging perimeters: Check
  Seam position: Random
  Fill desity: 20%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
  Infill/Perimeters overlap: 20%
  Bridge flow ratio: 0.95
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm


comments powered by Disqus

Similar items

Browse more newly listed 3D printings