Make pre-order

Sekiro 3D Printing Figurine | Assembly

average
cm: 29 w x 21.8 d x 26 h
in: 11.417 w x 8.583 d x 10.236 h
32
BUY FOR  $24.99

Source Files

|

Description

|

Printing Details

This 3D Figurine consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Sekiro 3D Printing Figurine comes in 4 versions for each 3D printer type (FFF/FDM, DLP/SLA and SLS). Files for each version are available for download after the purchase.

Detailed information about this 3D printing figurine is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
1_head_FDM(repaired).stl
19.20 MiB 1 h 17 min
1 m
31 x 21 x 31 Download
2_knot_FDM(repaired).stl
8.70 MiB 25 min
<1 m
14 x 13 x 23 Download
3_body_FDM(repaired).stl
33.14 MiB 9 h 29 min
5 m
63 x 47 x 73 Download
4_legs_FDM(repaired).stl
28.21 MiB 22 h 59 min
15 m
148 x 78 x 87 Download
5_arm_R_FDM(repaired).stl
12.84 MiB 2 h 43 min
2 m
30 x 36 x 51 Download
6_hand_R_FDM(repaired).st l
19.40 MiB 1 h 58 min
1 m
18 x 36 x 48 Download
7_arm_L_1_FDM(repaired).s tl
17.10 MiB 1 h 21 min
1 m
37 x 18 x 34 Download
8_arm_L_2_FDM(repaired).s tl
15.21 MiB 1 h 3 min
<1 m
22 x 16 x 44 Download
9_hand_L_FDM(repaired).st l
17.66 MiB 26 min
<1 m
15 x 12 x 26 Download
10_foot_R_FDM(repaired).s tl
17.66 MiB 4 h 9 min
3 m
42 x 38 x 66 Download
11_foot_L_FDM(repaired).s tl
16.10 MiB 3 h 46 min
2 m
37 x 29 x 67 Download
12_apparel_1_FDM(repaired ).stl
10.24 MiB 60 min
<1 m
16 x 14 x 71 Download
13_apparel_2_FDM(repaired ).stl
17.46 MiB 2 h 1 min
1 m
35 x 17 x 56 Download
14_apparel_3_FDM(repaired ).stl
14.84 MiB 9 h 35 min
6 m
72 x 77 x 136 Download
15_sword_1_FDM(repaired). stl
14.76 MiB 1 h 22 min
1 m
147 x 145 x 22 Download
16_scabbard_1_FDM(repaire d).stl
17.97 MiB 47 min
<1 m
5 x 143 x 11 Download
17_sword_2_FDM(repaired). stl
11.96 MiB 59 min
<1 m
17 x 15 x 53 Download
18_scabbard_2_FDM(repaire d).stl
12.92 MiB 1 h 42 min
1 m
119 x 131 x 12 Download
19_bamboo_FDM(repaired).s tl
9.40 MiB 1 h 33 min
1 m
29 x 19 x 108 Download
20_fern_1_FDM(repaired).s tl
10.47 MiB 4 h 56 min
4 m
52 x 59 x 49 Download
21_fern_2_FDM(repaired).s tl
10.82 MiB 3 h 55 min
3 m
38 x 36 x 74 Download
22_fern_3_FDM(repaired).s tl
10.36 MiB 3 h 45 min
3 m
38 x 38 x 61 Download
23_fern_4_FDM(repaired).s tl
12.40 MiB 3 h 49 min
3 m
46 x 39 x 49 Download
24_fern_5_FDM(repaired).s tl
13.17 MiB 3 h 5 min
2 m
38 x 23 x 80 Download
25_fern_6_FDM(repaired).s tl
11.03 MiB 4 h 5 min
3 m
40 x 47 x 55 Download
26_fern_7_FDM(repaired).s tl
13.17 MiB 2 h 53 min
2 m
35 x 35 x 72 Download
27_platform_1_FDM(repaire d).stl
20.08 MiB 13 h 14 min
7 m
128 x 112 x 24 Download
28_platform_2_FDM(repaire d).stl
20.73 MiB 12 h 2 min
7 m
112 x 113 x 25 Download
29_platform_3_FDM(repaire d).stl
17.45 MiB 10 h 6 min
6 m
110 x 83 x 24 Download
30_platform_4_FDM(repaire d).stl
15.15 MiB 10 h 48 min
6 m
124 x 82 x 27 Download
31_ge_lock_7S(x1)_FDM(rep aired).stl
0.02 MiB 3 min
<1 m
7 x 18 x 2 Download
32_ge_lock_10H(x8)_FDM(re paired).stl
0.03 MiB 4 min
<1 m
10 x 18 x 2 Download
Keychain (repaired).stl
0.35 MiB 23 min
<1 m
30 x 30 x 2 Download
Tag (repaired).stl
1.70 MiB 1 h 16 min
1 m
150 x 18 x 5 Download

ABOUT THIS 3D FIGURINE

Sekiro, also known as Wolf, is a solitary shinobi who is the protagonist of Sekiro: Shadows Die Twice action-adventure video game. Bound by the Iron Code to protect his young master, the Divine Heir, Sekiro loses his left arm in the game’s prologue that is later replaced by the Shinobi Prosthetic. Brave and loyal, Sekiro is loved by video game fans from all over the world and one of such enthusiasts happens to be our contributing 3D artist. Having spent 202 hours in total, the author of Sekiro figurine for 3D printing submitted an incredible Wolf model where the finest elements are taken care of. A Shinobi for 3D printing is depicted holding his primary Kusabimaru katana that the warrior is known to receive from the Divine Heir. There is also a second weapon - The Mortal Blade, also known as Fushigiri, on his back that the 3D printing hero keeps in case of a need to slay the undying. Wolf’s trademark Shinobi Prosthetic is equipped with the player character’s default Grapple Hook that ensures quick movement and is meticulously made with attention to all little fasteners and hardware. 3D printing Sekiro’s face is covered with scars and marks that Wolf received while training to become a Shinobi. For the purpose of conveying the atmosphere of the beautiful 16th century Sengoku Japanese nature, the 3D artist adorned the figurine’s platform with cherry blossom, bamboo fragments and leaves of a fern. A mysterious monk the Sculptor is known to have a collection of carved Buddhist statues. We are not sure what your collection comprises but a 3D printed Sekiro has all chances to become its gem!

ADAPTATION FOR 3D PRINTING

Sekiro figurine for 3D printing is a static assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 50 hours in total. Figurine’s anatomy was thoroughly reviewed during the moderation process for the samurai to be depicted harmoniously in the intended fighting pose. The model’s cutting was chosen by our team to minimise the amount of filament needed for generated support and some of the parts were hollowed out for you to save resin in the model’s Eco version. In order to conceal the places where the assembly parts of the model must be connected, the figurine was cut along the contour of the character’s armour seams and warrior’s Kusabimaru was extracted from Sekiro’s hold. For you to achieve the cleanest result possible such smaller parts as Sekiro’s Kusabimaru, its scabbard, the Mortal Blade, its handle, samurai’s boots, his shinobi prosthetic, hair bun etc. are provided as separate files. The leaves of fern and bamboo fragments that adorn the platform also come as separated 3D printing elements. All the assembly parts come in STL files in recommended positions that were worked out so to ensure the smoothness of the details’ surfaces after printing and that the 3D printing beginners won't face difficulties when placing the parts on a build plate. When downloading any figurine's file you will also receive "Assembly Manual" for FFF/FDM 1.0 and DLP/SLA 1.0 versions in PDF format.

The figurine is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from Sekiro's actual height that is 1800 mm. The 3D printing figurine's chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS versions.

VERSIONS' SPECIFICATIONS

FFF/FDM 1.0 version features:
- Contains 32 parts;
- A printed model is 260 mm tall, 290 mm wide, 218 mm deep;
- Assembly kit includes locks to attach the model's parts securely without glue. One lock 31_ge_lock_7S(x1) needs to be printed once; lock 32_ge_lock_10H(x8) needs to be printed 8 times;
- Made with a platform to recreate the nature of 16th century Sengoku Japan;
- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:
- Contains 10 parts;
- A printed model is 130 mm tall, 145 mm wide, 109 mm deep;
- Made with a platform to recreate the nature of 16th century Sengoku Japan;
- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

DLP/SLA Eco 1.0 version features:
- Contains 10 parts;
- A printed model is 130 mm tall, 145 mm wide, 109 mm deep;
- Made with a platform to recreate the nature of 16th century Sengoku Japan;
- Contains some hollowed out parts to save resin.

SLS 1.0 version features:
- Made as a solid one-piece figurine;
- A printed model is 130 mm tall, 145 mm wide, 109 mm deep;
- Contains 3 parts - one-piece Sekiro model and the figurine with the platform separated.

WHAT WILL YOU GET AFTER PURCHASE?

- STL files of Sekiro​ 3D Figurine for 3D printing which consist of 55 parts;
- 4 versions of files for this model for FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS;
- High-poly detailed figurine of Sekiro​;
Assembly Manual for FFF/FDM 1.0 and DLP/SLA 1.0 versions in PDF format;
- Detailed settings that we provide as a recommendation for Cura 3.5.1, Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get the figurine of Sekiro​​ for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Sekiro​ 3D Printing Figurine at Gambody YouTube channel.

Also, you may like other Heroes 3D Printing Figurines.

_______
FAQ: 

Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.5.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for CuraSimplify3D and Slic3r softwares.

Cura printing recommendations:

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

To avoid printing problems, we recommend the following settings:

Quality
Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Shell 
Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill 
Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Material 
Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Speed 
Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s 
     Support Infill Speed: 45 mm/s
Travel Speed: 45 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 45 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Travel 
Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.6562 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Cooling 
Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Support 
Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 2.2 mm
Support Z Distance: 0.13 mm
    Support Top Distance: 0.13 mm
    Support Bottom Distance: 0.13 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 15 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Experimental
Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Extruder
Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Layer
Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Additions
Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Infill
Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Support
Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Temperature
Extruder 1 Temperature: 210
Heated Bed: 60

Cooling
Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Speeds
Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Other
Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
Quality
  Detect thin walls: Check
  Detect bridging perimeters: Check
Advanced
  Seam position: Random
Infill
  Fill desity: 20%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
Advanced
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
Skirt
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
Brim 
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
Raft
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
Modifiers
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
Autospeed
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
Overlap
  Infill/Perimeters overlap: 20%
Flow
  Bridge flow ratio: 0.95
Other
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm

Comments

comments powered by Disqus

Similar items

Browse more newly listed 3D printings