Godzilla 2014 3D Printing Figurine | Assembly

cm: 45.9 w x 98.1 d x 46 h
in: 18.071 w x 38.622 d x 18.11 h

Source Files




Printing Details

This 3D Figurine consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Godzilla 2014 3D printing figurine comes in 4 versions for each 3D printer type (FFF/FDM, DLP/SLA and SLS). Files for each version are available for download after the purchase.

Detailed information about this 3D printing figurine is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
27.13 MiB 109 h 18 min 67 m Download
3_pelvis_FDM(repaired).st l
25.73 MiB 109 h 33 min 73 m Download
4_tail_1_FDM(repaired).st l
24.77 MiB 125 h 55 min 83 m 160 x 161 x 169 Download
5_tail_2_FDM(repaired).st l
26.55 MiB 93 h 31 min 57 m 136 x 144 x 162 Download
6_tail_3_FDM(repaired).st l
20.93 MiB 65 h 21 min 45 m 95 x 155 x 174 Download
7_tail_4_FDM(repaired).st l
17.94 MiB 26 h 54 min 17 m 87 x 94 x 145 Download
8_tail_5_FDM(repaired).st l
16.13 MiB 9 h 47 min 6 m 45 x 52 x 138 Download
9_tail_6_FDM(repaired).st l
11.94 MiB 5 h 59 min 4 m 47 x 66 x 153 Download
10_arm_R_FDM(repaired).st l
17.47 MiB 19 h 13 min 13 m 107 x 95 x 90 Download
11_hand_R_FDM(repaired).s tl
9.92 MiB 2 h 31 min 1 m 34 x 42 x 48 Download
12_arm_L_FDM(repaired).st l
17.05 MiB 17 h 36 min 11 m 79 x 119 x 90 Download
13_hand_L_FDM(repaired).s tl
10.01 MiB 2 h 27 min 1 m 33 x 41 x 53 Download
14_leg_R_FDM(repaired).st l
17.50 MiB 67 h 26 min 43 m 154 x 154 x 116 Download
15_foot_R_FDM(repaired).s tl
17.44 MiB 32 h 10 min 22 m 80 x 118 x 109 Download
16_leg_L_FDM(repaired).st l
18.02 MiB 62 h 58 min 39 m 153 x 154 x 117 Download
17_foot_L_FDM(repaired).s tl
19.10 MiB 33 h 1 min 21 m 79 x 95 x 132 Download
18_plate_1_FDM(repaired). stl
8.17 MiB 3 h 38 min 2 m 18 x 94 x 70 Download
19_plate_2_FDM(repaired). stl
2.85 MiB 47 min <1 m 12 x 34 x 37 Download
20_plate_3_FDM(repaired). stl
1.43 MiB 28 min <1 m 14 x 19 x 32 Download
21_plate_4_FDM(repaired). stl
3.73 MiB 1 h 13 min 1 m 14 x 57 x 37 Download
22_plate_5_FDM(repaired). stl
5.48 MiB 1 h 49 min 1 m 17 x 64 x 43 Download
23_plate_6_FDM(repaired). stl
19.42 MiB 11 h 22 min 6 m 35 x 138 x 99 Download
24_plate_7_FDM(repaired). stl
9.64 MiB 5 h 34 min 3 m 29 x 112 x 68 Download
25_plate_8_FDM(repaired). stl
9.97 MiB 5 h 59 min 3 m 29 x 125 x 74 Download
26_plate_9_FDM(repaired). stl
11.11 MiB 7 h 24 min 4 m 36 x 113 x 89 Download
27_plate_10_FDM(repaired) .stl
3.21 MiB 2 h 3 min 1 m 47 x 25 x 55 Download
28_plate_11_FDM(repaired) .stl
2.85 MiB 1 h 52 min 1 m 24 x 51 x 53 Download
29_plate_12_FDM(repaired) .stl
2.78 MiB 1 h 27 min 1 m 17 x 44 x 45 Download
30_plate_13_FDM(repaired) .stl
2.47 MiB 1 h 25 min 1 m 35 x 18 x 58 Download
31_plate_14_FDM(repaired) .stl
2.78 MiB 1 h 26 min 1 m 18 x 42 x 55 Download
32_plate_15_FDM(repaired) .stl
3.47 MiB 1 h 55 min 1 m 39 x 23 x 54 Download
33_plate_16_FDM(repaired) .stl
3.20 MiB 1 h 35 min 1 m 42 x 19 x 53 Download
34_plate_17_FDM(repaired) .stl
2.22 MiB 59 min 1 m 49 x 12 x 41 Download
35_plate_18_FDM(repaired) .stl
2.35 MiB 1 h 8 min 1 m 12 x 54 x 38 Download
36_plate_19_FDM(repaired) .stl
3.44 MiB 1 h 48 min 1 m 47 x 20 x 50 Download
37_plate_20_FDM(repaired) .stl
3.68 MiB 54 min <1 m 10 x 40 x 44 Download
38_platform_1_FDM(repaire d).stl
16.04 MiB 25 h 14 min 15 m 141 x 142 x 32 Download
39_platform_2_FDM(repaire d).stl
16.07 MiB 44 h 39 min 26 m 152 x 155 x 52 Download
40_platform_3_FDM(repaire d).stl
14.52 MiB 25 h 3 min 15 m 141 x 144 x 34 Download
41_platform_4_FDM(repaire d).stl
15.57 MiB 43 h 16 min 25 m 154 x 151 x 50 Download
42_platform_5_FDM(repaire d).stl
16.94 MiB 42 h 45 min 25 m 152 x 151 x 33 Download
43_platform_6_FDM(repaire d).stl
15.31 MiB 42 h 28 min 25 m 153 x 151 x 42 Download
44_platform_7_FDM(repaire d).stl
14.56 MiB 26 h 18 min 16 m 140 x 141 x 50 Download
45_platform_8_FDM(repaire d).stl
15.33 MiB 42 h 58 min 25 m 152 x 152 x 33 Download
46_platform_9_FDM(repaire d).stl
14.53 MiB 25 h 25 min 15 m 141 x 140 x 33 Download
Keychain (repaired).stl
0.35 MiB 23 min <1 m 30 x 30 x 2 Download
Tag (repaired).stl
1.70 MiB 1 h 16 min 1 m 150 x 18 x 5 Download
48_body_v2_FDM(repaired). stl
62.37 MiB 24 h 42 min 14 m Download
49_tongue_v2_FDM(repaired ).stl
2.51 MiB 27 min <1 m 11 x 14 x 34 Download
7_v2_tail_4_FDM(repaired) .stl
34.27 MiB 45 h 4 min 31 m 81 x 151 x 141 Download
8_v2_tail_5_FDM(repaired) .stl
31.43 MiB 27 h 47 min 17 m 86 x 153 x 133 Download
9_v2_tail_6_FDM(repaired) .stl
24.30 MiB 17 h 33 min 13 m 47 x 126 x 163 Download
47_ge_lock_10H(x90)_FDM(r epaired).stl
0.03 MiB 4 min <1 m 18 x 10 x 2 Download
0.02 MiB 3 min <1 m 18 x 7 x 2 Download
1_head_FDM(repaired)1 (re paired).stl
76.93 MiB 25 h 2 min 13 m Download


2014 Godzilla movie turned out to be a pretty refreshing look at the well-loved monster universe. A 2-hour blockbuster shows the usual havoc that the titular monster spreads and being the Hollywood-produced film, the action takes place mostly in U.S. cities. The author of the gigantic Godzilla figurine for 3D printing rejoiced all fans of modern American MonsterVerse and came up with this brilliant and deadly kaiju figurine. The whole project took the 3D artist about 240 hours to complete and now the 90,000-ton King of the Monsters is featured in its 3D printing form in Gambody’s Kaiju category. The appearance of the destructive creature figurine is as realistic as ever. Inspired by the 2014 film by Legendary Pictures, the 3D artist depicted the Titanus Gojira with his blocky face, small eyes, thick neck and shark-like gills, making the monster look more reptile-like. 3D printing Godzilla's dorsal plates are small but seem to be extremely sharp and are located all along the monster’s bulky back and tail. The King of the Monster overall looks exceptionally heavy so no wonder it takes much effort to tame the beast. The creature’s creators revealed that this massive Godzilla’s roar can be heard from 3 miles away and given his looks we can totally believe it! Order the STL files of the Godzilla 2014 figurine and 3D print your own Massive Unidentified Terrestrial Organism. 


Godzilla 2014 is a static assembly figurine and its moderation and adaptation for different types of 3D printers took Gambody team 56 hours in total. The huge figurine was divided into as many assembly parts as needed to fit even the smallest 3D printers' build plates and for you to nevertheless receive a giant 3D printed kaiju after assembly. The cutting of Godzilla figurine was chosen by our team to minimise the amount of filament needed for generated support and some of the model’s parts were hollowed out for you to save resin in the model’s Eco version. In order to receive the cleanest result possible all dorsal plates located along the monster’s back and tail were extracted and are now provided as 20 separate parts, each having a designated assembly notch. The model’s platform was also divided into nine pieces in the assembly version to fit even the smallest build plates. All assembly parts are provided in STL files in recommended positions that were worked out so to ensure the smoothness of the details’ surfaces after printing and that the 3D printing beginners won't face difficulties when placing the parts on a build plate. When downloading any figurine's file you will also receive "Assembly Manual" for FFF/FDM 1.0 and DLP/SLA 1.0 versions in PDF format.

The figurine is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from 2014 Godzilla's actual height that is 108200 mm. The 3D printing figurine's chosen scale is 1/250 for the FFF/FDM version and 1/500 for the DLP/SLA/SLS versions.


FFF/FDM 1.0 version features:
- Contains 49 parts;
- A printed model is 460 mm tall, 459 mm wide, 981 mm deep;
- Assembly kit includes lock 47_ge_lock_10H(x88) to connect the model's parts securely without glue that needs to be printed 88 times;
- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:
- Contains 19 parts;
- A printed model is 230 mm tall, 230 mm wide, 491 mm deep;
- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

DLP/SLA Eco 1.0 version features:
- Contains 19 parts;
- A printed model is 230 mm tall, 230 mm wide, 491 mm deep;
- Contains some hollowed out parts to save resin.

SLS 1.0 version features:
- Made as solid one-piece figurine;
- A printed model is 230 mm tall, 230 mm wide, 491 mm deep;
- Contains 3 parts - two variants of the one-piece figurine (open and closed mouth) with the platform separated.


- STL files of Godzilla 2014 3D printing figurine which consist of 90 parts;
- 4 versions of files for this model for FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS;
- High-poly detailed figurine of Godzilla 2014;
Assembly Manual for FFF/FDM 1.0 and DLP/SLA 1.0 versions in PDF format;
- Detailed settings that we provide as a recommendation for Cura , Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get Godzilla 2014 3D printing figurine​ immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Godzilla 2014 3D printing figurine at Gambody YouTube channel.

Also, you may like other Kaiju Figurines for 3D Printing.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

Below you can find printing recommendations for CuraSimplify3D and Slic3r software.

Cura printing recommendations:

These are basic settings that were tested in Cura 4.8.0 slicer. 

The test models were printed on Ultimaker 2, Creality Ender 3, Creality CR-10S Pro V2, Anycubic I3 Mega, Anycubic I3 MegaS 3D printers with PLA and PETG filaments.

Disclaimer: The following printing settings are a recommendation, not an obligation. The parameters can vary depending on the peculiarities of your 3D printer, the material you use and especially the particular assembly part at hand. Each part that any model comprises often needs preliminary review and you are free to tweak the settings the way you find suitable.

- You can scale up the model (downscaling is not recommended!);
- All connectors should be printed at 100% Infill;
- For all parts of locks (“ge_lock” in “Source files”) you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

Layer Height: 0.12 mm (you can also set Layer Height at 0.16 or 0.2mm for 0.4mm nozzles)
Initial Layer Height: 0.2 mm (carefully level the print bed and keep your Initial Layer Height the same as the main Layer Height)

Line Width: 0.4 mm
Wall Line Width: 0.4 mm
Outer Wall Line Width: 0.4 mm
Inner Wall(s) Line Width: 0.4 mm
Top/Bottom Line Width: 0.4 mm
Infill Line Width: 0.4 mm
Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm

Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
Wall Line Count: 2

Outer Wall Wipe Distance: 0.3 mm
Top Surface Skin Layers: 0

Top/Bottom Thickness: 0.6 mm
Top Thickness: 0.6 mm
Top Layers: 5
Bottom Thickness: 0.6 mm
Bottom Layers: 5
Initial Bottom Layers: 5

Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Optimize Wall Printing Order: Check

Compensate Wall Overlaps: Check
Compensate Inner Wall Overlaps: Check

Minimum Wall Flow: 0%
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Hole horizontal expansion: 0

Z Seam Alignment: User Specified
Z Seam Position: Back
Z Seam X: Average length of your printer’s plate (e.g.”150” if your plate is 300mm on the X-axis)
Z Seam Y: A value higher than the length of your plate on the Y-axis (e.g. 700)

Seam Corner Preference: Hide Seam
Extra Skin Wall Count: 1
Skin Overlap Percentage: 10%
Skin Overlap 0.04 mm

Infill Density: 20% (for all smaller parts and for all parts of connectors use 100% Infill)
Infill Pattern: Triangles
Connect Infill Lines: Check
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Line Multiplier: 1
Extra Infill Wall Count: 0

Infill Overlap Percentage: 10-20%
Infill Overlap: 0.04 mm

Skin Overlap Percentage: 5%
Skin Overlap: 0.02 mm

Infill Wipe Distance: 0 mm
Infill Layer Thickness: 0.24 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2

Skin Removal Width: 0.8 mm
Top Skin Removal Width: 0.8 mm
Bottom Skin Removal Width: 0.8 mm

Skin Expand Distance: 0.8
Top Skin Expand Distance: 0.8
Bottom Skin Expand Distance: 0.8

Maximum Skin Angle for Expansion: 90˚
Minimum Skin Width for Expansion: 0.0
Skin Edge Support Thickness: 0
Skin Edge Support Layers: 0

Initial Layer Flow: 100%
Printing Temperature: See your filament settings
Initial Printing Temperature: Your filament settings
Final Printing Temperature: Your filament settings
Build Plate Temperature: Your filament settings
Build Plate Temperature Initial Layer: Your filament settings + 5°
Flow: 100% (Important! If you face difficulty printing the model, you may need to adjust the Flow parameter. You may research the topic using the Internet or seek assistance at our Customer Support Team at support@gambody.com)


You can increase the printing Speed by 20% when you print simple objects. For small/thin parts you need to decrease the Speed by 25% - 50%.

Print Speed: 50 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 25 mm/s
          Outer Wall Speed:25 mm/s
          Inner Wall Speed: 50 mm/s

Top/Bottom Speed: 25mm/s
Support Speed: 25 mm/s 
          Support Infill Speed: 45 mm/s
          Support Interface Speed: 25 mm/s
                Support Roof Speed: 25 mm/s
                Support Floor Speed: 25 mm/s

Travel Speed: 80 mm/s
Initial Layer Speed: 80 mm/s
Initial Layer Print Speed: 20 mm/s
Initial Layer Travel Speed: 80 mm/s

Skirt/Brim Speed: 20 mm/s
Z  Hop Speed: 5 mm/s
Number of Slower Layers: 2
Enable Acceleration Control: Check

When printing simple objects, you need to set all Acceleration parameters at 500 mm/s. For small/thin parts you need to decrease the Acceleration by 50% - 70%.

Enable Retraction: Check
Retraction Distance: 4-8 mm, 1-3 mm for Direct Extruder (This is the most important retraction parameter. You can find your optimal value of Retraction Distance by printing any test object, e.g. bridges, towers etc.)

Retraction Speed: 25mm/s
Retraction Retract Speed: 25 mm/s
Retraction Prime Speed: 25 mm/s

Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 1.5 mm
Maximum Retraction Count: 100
Minimum Extrusion Distance Window: 6,5 - 10 mm
Limit Support Retractions: Check
Combing Mode: All
Max Comb Distance With No Retract: 30 mm
Retract Before Outer Wall: Check
Avoid Printed Parts When Travelling: Check
Avoid Supports When Travelling: Check
Travel Avoid Distance: 1 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm
Z Hop When Retracted: Check
Z Hop Height: 0,3 mm

Enable Print Cooling: Check
Fan Speed: 100%
Regular Fan Speed: 100%
Maximum Fan Speed: 100% 

Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.36 mm
Regular Fan Speed at Layer: 3 

Minimum Layer Time: 10 s
Minimum Speed: 10 mm/s

Generate Support: Check
Support Structure: Normal (you can try using Tree Support Structure if you have difficulty printing any particular assembly part)
Support Placement: Everywhere 
Support Overhang Angle: 60° (this parameter can range from 30° to 70° depending on the part at hand)
Support Pattern: Zig Zag
Support Wall Line Count: 1 (stronger support that might be more difficult to remove) 0 (less strong support but is easier to remove)

Support Density: 15%
Support Line Distance: 2.6667 mm
Initial layer support line distance: 2.667 mm

Support Z Distance: 0.12 mm
Support Top Distance: 0.12 mm
Support Bottom Distance: 0.12 mm

Support X/Y Distance: 0.8-1 mm
Support Distance Priority: Z overrides X/Y
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Stair Step Minimum Slope Angle: 10°
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.2 mm
Gradual Support Infill Steps: 0
Minimum Support Area: 2 mm

Enable Support Interface: Check (generates additional “pillow” on the support structure that leads to a more even surface, but can be difficult to remove in hard-to-reach areas)
Enable Support Roof: Check
Enable Support Floor: Check

Support Interface Thickness: 0.8 mm
Support Roof Thickness: 0.8 mm
Support Floor Thickness: 0.8 mm

Support Interface Resolution 0.2 mm
Support Interface Density: 50-100%
        Support Roof Density: 50-100%
Support Roof Line Distance: 0.8 mm
        Support Floor Density: 50-100%
Support Floor line Distance:  0.4mm

Support Interface Pattern: Grid 
Support Roof Pattern: Grid (this parameter should differ from Bottom Pattern Initial Layer in “Shell” section)
Support Floor Pattern: Grid

Minimum Support Interface Area: 10mm
Minimum Support Roof Area: 10 mm
Minimum Support Floor Area: 10 mm

Support Interface Horizontal Expansion: 0.0 mm
Support Roof Horizontal Expansion: 0.0 mm
Support Floor Horizontal Expansion: 0.0 mm

Fan Speed Override: Check
Supported Skin Fan Speed: 100%
Use Towers: Check
Tower Diameter: 4 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Skirt/Brim (For unsteady parts, and those parts that may come unstuck use “Brim”. For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
       Brim Line Count: 10
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Extruder 1 Temperature: 210
Heated Bed: 60

Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
  Detect thin walls: Check
  Detect bridging perimeters: Check
  Seam position: Random
  Fill desity: 20%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
  Infill/Perimeters overlap: 20%
  Bridge flow ratio: 0.95
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm


comments powered by Disqus

Similar items

Browse more newly listed 3D printings