Make pre-order

Godzilla The SoshingekiGoji 3D Printing Figurine | Assembly

cm: 16.7 w x 28.1 d x 21.1 h
in: 6.575 w x 11.063 d x 8.307 h
BUY FOR  $24.99

Source Files




Printing Details

This 3D Figurine consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Godzilla The SoshingekiGoji 3D printing figurine comes in 4 versions for each 3D printer type (FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS). Files for each version are available for download after the purchase.

Detailed information about this 3D printing figurine is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
27.37 MiB 5 h 58 min
3 m
38 x 49 x 64 Download
2_jaw_low_FDM(repaired).s tl
6.50 MiB 55 min
<1 m
23 x 32 x 16 Download
3_jaw_top_FDM(repaired).s tl
5.65 MiB 18 min
<1 m
22 x 21 x 11 Download
4_body_1_FDM(repaired).st l
27.10 MiB 13 h 44 min
8 m
62 x 78 x 73 Download
5_body_2_FDM(repaired).st l
30.28 MiB 20 h 33 min
12 m
66 x 81 x 97 Download
6_tail_1_FDM(repaired).st l
16.65 MiB 14 h 18 min
10 m
58 x 71 x 91 Download
7_tail_2_FDM(repaired).st l
16.22 MiB 7 h 9 min
5 m
44 x 58 x 80 Download
8_tail_3_FDM(repaired).st l
8.67 MiB 2 h 52 min
2 m
28 x 37 x 75 Download
9_arm_L_1_FDM(repaired).s tl
8.08 MiB 1 h 57 min
1 m
43 x 32 x 31 Download
10_arm_L_2_FDM(repaired). stl
8.90 MiB 47 min
<1 m
18 x 19 x 38 Download
11_hand_L_FDM(repaired).s tl
8.45 MiB 34 min
<1 m
16 x 18 x 26 Download
12_arm_R_1_FDM(repaired). stl
8.92 MiB 2 h 7 min
1 m
43 x 34 x 34 Download
13_arm_R_2_FDM(repaired). stl
6.43 MiB 1 h 6 min
1 m
23 x 20 x 41 Download
14_hand_R_FDM(repaired).s tl
9.19 MiB 35 min
<1 m
17 x 18 x 24 Download
15_leg_L_FDM (repaired).s tl
15.05 MiB 7 h 33 min
4 m
53 x 78 x 47 Download
16_foot_L_FDM(repaired).s tl
19.34 MiB 5 h 53 min
4 m
51 x 53 x 58 Download
17_leg_R_FDM (repaired).s tl
15.54 MiB 8 h 8 min
5 m
72 x 62 x 49 Download
18_foot_R_FDM(repaired).s tl
19.17 MiB 5 h 41 min
3 m
49 x 58 x 52 Download
19_plate_1_FDM(repaired). stl
0.76 MiB 14 min
<1 m
6 x 23 x 15 Download
20_plate_2_FDM(repaired). stl
2.43 MiB 26 min
<1 m
9 x 27 x 30 Download
21_plate_3_FDM(repaired). stl
0.76 MiB 13 min
<1 m
6 x 23 x 15 Download
22_plate_4_FDM(repaired). stl
1.45 MiB 18 min
<1 m
8 x 25 x 19 Download
23_plate_5_FDM(repaired). stl
4.63 MiB 46 min
<1 m
12 x 34 x 41 Download
24_plate_6_FDM(repaired). stl
1.40 MiB 18 min
<1 m
8 x 25 x 19 Download
25_plate_7_FDM(repaired). stl
1.00 MiB 15 min
<1 m
9 x 22 x 17 Download
26_plate_8_FDM(repaired). stl
2.60 MiB 35 min
<1 m
14 x 29 x 31 Download
27_plate_9_FDM(repaired). stl
0.91 MiB 16 min
<1 m
9 x 22 x 17 Download
28_plate_10_FDM(repaired) .stl
2.15 MiB 35 min
<1 m
12 x 29 x 30 Download
29_plate_11_FDM(repaired) .stl
1.65 MiB 21 min
<1 m
11 x 27 x 23 Download
30_platform_1_FDM(repaire d).stl
19.82 MiB 11 h 40 min
7 m
166 x 84 x 21 Download
31_platform_2_FDM(repaire d).stl
25.47 MiB 11 h 41 min
7 m
166 x 84 x 28 Download
32_ge_lock_10H(x8)_FDM(re paired).stl
0.03 MiB 4 min
<1 m
10 x 18 x 2 Download
33_ge_lock_7S(x1)_FDM(rep aired).stl
0.02 MiB 3 min
<1 m
7 x 18 x 2 Download
Keychain (repaired).stl
0.35 MiB 23 min
<1 m
30 x 30 x 2 Download
Tag (repaired).stl
1.70 MiB 1 h 16 min
1 m
150 x 18 x 5 Download


The SoshingekiGoji is one of the first Godzilla suit designs that was used in four consecutive movies within the Showa Era from 1968 to 1972. At the time when advanced technologies and CGI weren’t available to the creators of larger-than-life projects, the process of bringing the monster character to life required great efforts and challenged actors and prop designers. And if different Godzilla appearances may strike as similar, the real kaiju fan will unmistakably tell the Era or even the film a given Godzilla belongs to solely by the looks of the monster. The author of this 3D printing figurine is a well-known kaiju enthusiast so he spent 180 hours to design the legendary and extremely durable SoshingekiGoji figurine for 3D printing. This rubber costume is considered to be even more valuable by fans being the last suit the very first Godzilla stuntman Haruo Nakajima would portray the monster in. The creature that was wreaking havoc upon the towns of Japan is slowly transforming from unstoppable force into a friendly superhero and we have no doubts the 3D printed figurine will add to your awesome kaiju collection. 


Godzilla The SoshingekiGoji is a static assembly figurine and its moderation and adaptation for different types of 3D printers took Gambody team 56 hours in total. The cutting of Godzilla figurine was chosen by our team to minimise the amount of filament needed for generated support and some of the model’s parts were hollowed out for you to save resin in the model’s Eco version. In order to receive the cleanest result possible all dorsal plates located along the monster’s back were extracted and are now provided as 11 separate parts, each having a designated assembly notch. With the same purpose, the monster’s jaws were extracted from the figurine’s mouth and are now provided as two separate parts. The model’s platform was divided in half in the assembly version to fit even the smallest build plates. All assembly parts are provided in STL files in recommended positions that were worked out so to ensure the smoothness of the details’ surfaces after printing and that the 3D printing beginners won't face difficulties when placing the parts on a build plate. 

The figurine is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from Godzilla The SoshingekiGoji's actual height that is 50000 mm. The 3D printing figurine's chosen scale is 1/250 for the FFF/FDM version and 1/500 for the DLP/SLA/SLS versions.


FFF/FDM 1.0 version features:
- Contains 33 parts;
- A printed model is 211 mm tall, 167 mm wide, 281 mm deep;
- Assembly kit includes locks to connect parts without glue. One lock 32_ge_lock_10H(x8)​ needs to be printed 8 times; lock​ 33_ge_lock_7S(x1) needs to be printed once;
- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:
- Contains 7 parts;
- A printed model is 106 mm tall, 84 mm wide, 141 mm deep;
- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

DLP/SLA Eco 1.0 version features:
- Contains 7 parts;
- A printed model is 106 mm tall, 84 mm wide, 141 mm deep;
- Contains some hollowed out parts to save resin.

SLS 1.0 version features:
- Made as solid one-piece figurine;
- A printed model is 106 mm tall, 84 mm wide, 141 mm deep;
- Contains 3 parts - a one-piece model and the figurine with the platform separated.


- STL files of Godzilla The SoshingekiGoji 3D printing figurine which consist of 50 parts;
- 4 versions of files for this model for FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS;
- High-poly detailed figurine of Godzilla The SoshingekiGoji;
- Detailed settings that we provide as a recommendation for Cura 3.5.1, Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get Godzilla The SoshingekiGoji 3D printing figurine​ immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Godzilla The SoshingekiGoji 3D printing figurine at Gambody YouTube channel.

Also, you may like other Kaiju Figurines for 3D Printing.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.5.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for CuraSimplify3D and Slic3r softwares.

Cura printing recommendations:

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

To avoid printing problems, we recommend the following settings:

Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s 
     Support Infill Speed: 45 mm/s
Travel Speed: 45 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 45 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.6562 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 2.2 mm
Support Z Distance: 0.13 mm
    Support Top Distance: 0.13 mm
    Support Bottom Distance: 0.13 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 15 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Extruder 1 Temperature: 210
Heated Bed: 60

Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
  Detect thin walls: Check
  Detect bridging perimeters: Check
  Seam position: Random
  Fill desity: 20%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
  Infill/Perimeters overlap: 20%
  Bridge flow ratio: 0.95
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm


comments powered by Disqus

Similar items

Browse more newly listed 3D printings