Make pre-order

cm: 12.6 w x 12.2 d x 22.3 h
in: 4.961 w x 4.803 d x 8.78 h
BUY FOR  $14.99

Source Files




Printing Details

This 3D model consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Version 1 and Version 2 are the files for Pickle Rick 3D Model optimized for 3D printing, the preview pictures of which you see above.

It is recommended:

  • to print Version 1 STL files on FDM/FFF 3D printers;
  • to print Version 2 STL files on DLP/SLA/SLS 3D printers.
File Name File Size Time / Filament
1_platform (repaired).stl
0.27 MiB 11 h 35 min
7 m
3_ge_connector_1 (repaire d).stl
0.04 MiB 15 min
<1 m
4_ge_connector_2 (repaire d).stl
0.04 MiB 15 min
<1 m
5_body (repaired).stl
8.46 MiB 7 h 49 min
4 m
6_arm_R (repaired).stl
4.23 MiB 2 h 23 min
1 m
7_arm_1_L (repaired).stl
3.35 MiB 2 h 11 min
1 m
8_arm_2_L_for_gun (repair ed).stl
5.83 MiB 1 h 59 min
1 m
2.77 MiB 7 h 45 min
5 m
10_battery (repaired).stl
0.18 MiB 40 min
<1 m
11_sub_gun (repaired).stl
1.54 MiB 21 min
<1 m
12_a1 (repaired).stl
6.92 MiB 3 h 25 min
2 m
13_a2 (repaired).stl
5.74 MiB 3 h 14 min
2 m
14_b1 (repaired).stl
8.99 MiB 3 h 42 min
2 m
15_b2 (repaired).stl
7.96 MiB 3 h 31 min
2 m
16_rat (repaired).stl
2.31 MiB 2 h 42 min
1 m
2_legs (repaired).stl
9.50 MiB 12 h 2 min
8 m


Pickle Rick, the cult transformation of the famous and beloved character Rick. He did this because don’t want to go see a psychologist with his family. Everything was fine until Beth guessed his intentions and take off the syringe with the antidote. And the story began with the fact that the impudent cat pushed Pickle out of the garage into the street. Whence he later got into the sewers. But of course the scientific genius with elements of insanity, even being a pickle in a smelly sewer will not be lost. He created himself an exoskeleton that consists pieces of the rat body. He got out of the sewer and ended up in jail in which he was considered as a threat. In order to get out of there, he created a powerful laser that cut everything around. All attempts to destroy him were unsuccessful and he killed everyone who was on his way. He got to the psychologist to pick up a syringe from his daughter. The inspiration for creating this model was taken by the incredible battles that Rick arranged. Your attention is presented to two of his options: with a laser and without it.


The model is saved in STL files, a format supported by most 3D printers.

FDM version features:

- Changeable hands with laser and without it;
- In the slot for laser charges are suitable batteries AAA type;
- All parts are divided in such way that you will print them with the smallest amount of supports.

SLS/SLA version features:

- Same as FDM but smaller and made with few details.

All .STL files for 3D printing have been corrected in Netfabb.

Note: Before starting 3D printing the model, read the Printing Details for CURA 3.0.4. software.

There are 11 parts for FDM version and 3 parts for SLS/SLA.
All parts of connectors should be printed at 100% infill.

Scale: Model made as the original size 1/1 scale in FDM version and 1/2 in SLS/SLA version.

FDM version dimensions:

- After being printed will stand 223 mm tall, 126 mm wide, 122 mm deep;

- Connectors should be printed at 100% infill to make them solid.

SLS/SLA version dimensions:

- After being printed will stand 111 mm tall, 63 mm wide, 61 mm deep;

- Has few details to keep printing costs down.


- .STL files of Pickle Rick for printing which consist of 14 parts;

- Changeable hands: with laser and without it;
- 2 versions of Pickle Rick;

- Detailed settings that we provide for Cura 3.0.4. for the best print;

- High-poly detailed model of Pickle Rick;

- Full technical support from the Gambody Support Team.

Watch the tutorial video on how to assemble Pickle Rick 3D Printing Miniature at Gambody YouTube channel.

Check this video with painted Pickle Rick 3D Model.

You can get Pickle Rick for 3D Printing right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Also, you may like another Heroes 3D models.


On 04.12.2017 model of Pickle Rick have been updated.

Now this model has new hands with weapons. Also, a rat head model was added which you can reduce or increase and print several times to create a diorama of Pickle Rick from famous cartoon.

Here is a list of new files:
FDM version:
1. (12_a1.stl) - first hand with bolt;
2. (13_a2.stl) - second hand with bolt;
3. (14_b1.stl) - first hand with blade;
4. (15_b2.stl) - second hand with blade;
5. (16_rat.stl) - one head of rat that you can print several times.

SLS/SLA version:
1. (4_rick_sls_2.stl) - model with blades;
2. (5_rick_sls_3.stl) - model with bolts;
3. (6_rat_sls.stl) - head of rat.

STL files are already available for download in “Source files” tab for Version 1 (FDM/FFF 3D printers) and Version 2 (SLS/SLA 3D printers). You can find them at the end of the list.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.0.4. and printed on an Ultimaker 2 in PLA material.

Note: All parts of connectors should be printed at 100% infill.

To avoid printing problems, we recommend the following settings:

Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
   Top/Bottom Line Width: 0.4 mm
   Infill Line Width: 0.4 mm
   Skirt/Brim Line Width: 0.4 mm
   Support Line Width: 0.4 mm
   Support Interface Line Width: 0.4 mm
   Support Roof Line Width: 0.4 mm
   Support Floor Line Width: 0.4
 Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill Density: 20% (all parts of the connectors should be printed at 100% infill)
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Print Speed: 45 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s
      Support Infill Speed: 45 mm/s
      Support Interface Speed: 30 mm/s
        Support Roof Speed: 30mm/s
        Support Floor Speed: 30 mm/s
Travel Speed: 80 mm/s
Initial Layer Speed: 15 mm/s

    Initial Layer Print Speed: 15 mm/s
    Initial Layer Travel Speed: 26.6667 mm/s
Skirt/Brim Speed: 15 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm 

Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Enable Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 30 %
    Support Line Distance: 1.3333 mm
Support Z Distance: 0.3 mm
    Support Top Distance: 0.3 mm
    Support Bottom Distance: 0.3 mm
Support X/Y Distance: 0.7 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.2 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm

Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 18 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.


comments powered by Disqus
Other author's 3D printings


Rick, Pickle Rick, heroes, Cartoon, Assembly

Similar items

Browse more newly listed 3D printings