Make pre-order

Ryuk 3D Printing Figurine | Assembly

cm: 30.7 w x 22.2 d x 37.9 h
in: 12.087 w x 8.74 d x 14.921 h
BUY FOR  $24.99

Source Files




Printing Details

This 3D Figurine consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Ryuk 3D printing figurine comes in 4 versions for each 3D printer type (FFF/FDM, DLP/SLA and SLS). Files for each version are available for download after the purchase.

Detailed information about this 3D printing figurine is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
40.97 MiB 3 h 52 min
2 m
53.19 MiB n.a.
86 x 57 x 101 Download
55.77 MiB 12 h 37 min
6 m
24.04 MiB 3 h 10 min
2 m
33 x 46 x 85 Download
21.13 MiB 3 h 8 min
2 m
51 x 36 x 85 Download
6_hand_R_FDM(repaired).st l
12.64 MiB 1 h 47 min
1 m
26 x 47 x 48 Download
7_hand_L_FDM(repaired).st l
14.47 MiB 1 h 32 min
1 m
30 x 29 x 51 Download
8_foot_R_FDM(repaired).st l
24.20 MiB 3 h 38 min
2 m
83 x 29 x 89 Download
9_foot_L_FDM(repaired).st l
22.48 MiB 3 h 32 min
2 m
35 x 87 x 83 Download
10_earring_FDM(repaired). stl
3.43 MiB 2 min
<1 m
4 x 13 x 2 Download
11_fur_R_FDM(repaired).st l
24.16 MiB 7 h 42 min
4 m
68 x 47 x 48 Download
12_fur_L_FDM(repaired).st l
25.89 MiB 6 h 40 min
3 m
43 x 62 x 46 Download
13_fur_back_FDM(repaired) .stl
14.69 MiB 13 min
<1 m
23 x 5 x 15 Download
14_buckle_FDM(repaired).s tl
8.69 MiB 33 min
<1 m
21 x 21 x 13 Download
29.20 MiB 1 h 45 min
1 m
35 x 44 x 17 Download
16_skulls_FDM(repaired).s tl
47.85 MiB 30 h 46 min
18 m
129 x 108 x 73 Download
17_platform_1_FDM(repaire d).stl
20.14 MiB 10 h 5 min
6 m
95 x 95 x 23 Download
18_platform_2_FDM(repaire d).stl
19.06 MiB 10 h 7 min
5 m
95 x 95 x 23 Download
19_platform_3_FDM(repaire d).stl
19.33 MiB 10 h 6 min
6 m
95 x 95 x 33 Download
20_platform_4_FDM(repaire d).stl
19.18 MiB 10 h 2 min
6 m
95 x 95 x 33 Download
21_ge_lock_7S(x5)_FDM(rep aired).stl
0.02 MiB 3 min
<1 m
18 x 7 x 2 Download
22_ge_lock_10H(x12)_FDM(r epaired).stl
0.03 MiB 4 min
<1 m
10 x 18 x 2 Download
Keychain (repaired).stl
0.35 MiB 23 min
<1 m
30 x 30 x 2 Download
Tag (repaired).stl
1.70 MiB 1 h 16 min
1 m
150 x 18 x 5 Download
54.84 MiB 16 h 60 min
11 m
24_claw_for_R_wing_FDM(re paired).stl
2.81 MiB 36 min
<1 m
27 x 18 x 34 Download
25_wing_R_FDM(repaired).s tl
41.11 MiB 15 h 39 min
9 m
26_claw_for_L_wing_FDM(re paired).stl
2.83 MiB 37 min
<1 m
21 x 24 x 36 Download
27_wing_L_FDM(repaired).s tl
33.26 MiB 16 h 15 min
9 m


Ryuk is a Shinigami, the Japanese god of death, that stars in the internationally acclaimed manga and anime series Death Note. Once Ryuk gets tired of the Shinigami realm and “accidentally” drops into the Human World the Death Note, a powerful notebook that can kill any human whose name is written in it. Although Ryuk’s actions are aimed at satisfying his need for entertainment, he eventually becomes a "moral compass" for the young man who picks up the Death Note. The apple-addicted, impartial observer of Light’s actions is presented as the embodiment of death itself who demonstrates that death never truly takes sides. Ryuk model for 3D printing depicts the everybody's favourite Shinigami soaring on top of two enormous skulls. The author of the 3D printing figurine masterly recreated the ghoulish appearance of the humanoid God of Death and made sure to properly accessorize the bizarre Shinigami. Thus, the 3D printing Ryuk is extremely slim, his limbs are abnormally long, the eyes are bulging and his back is hunched up, making Shinigami tower intimidatingly over the humans he observes. The omnipresent Ryuk for 3D printing styles his hair in a spiky manner, has several rings adorning his fingers, and wears two large feathery pieces on each shoulder. Finally, the stitches along the Shinigami’s collarbone, his trademark heart-shaped earring, and the stylish accessories that hang from his sinister-looking belt perfectly complete the image of the gloomy yet quirky Ryuk. Shinigami’s broad smile full of sharp, pointed teeth can be interpreted in many ways: God of Death might be looking for a nice and tasty red apple, or he might be searching for a new amusement out of boredom. Or, Ryuk figurine for 3D printing might be excited in anticipation of joining your collection of 3D printed models! After all, who would not like to acquire the very own powerful Shinigami!


Ryuk figurine for 3D printing is a static assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 44 hours in total. The figurine’s anatomy was thoroughly reviewed during the moderation process for the Death God to be depicted harmoniously in the intended soaring pose. The model’s cutting was chosen by our team to minimize the amount of filament needed for generated support and some of the parts were hollowed out for you to save resin in the model’s Eco version. Moreover, in order to conceal places where assembly parts of the figurine must be connected, the model was cut along the contour of Ryuk’s attire seams. The figurine's platform in its assembly version was divided into four separate parts in order to fit even the smallest 3D printers’ build plates, while the skull base was cut off as well. Besides, in order for you to receive the cleanest 3D printed result, such smaller parts as Ryuk’s belt buckle, heart-shaped earring, the Death Note that is to be chained to the belt, feather shoulder pieces, hands, etc. are also available as separate assembly pieces. All assembly parts are provided in STL files in recommended positions that were worked out in order to ensure the smoothness of the details’ surfaces after printing and so that the 3D printing beginners won't face difficulties when placing the parts on a build plate. When downloading any figurine's file you will also receive "Assembly Manual" for FFF/FDM 1.0 and DLP/SLA 1.0 versions in PDF format.

The figurine is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from Ryuk's actual height that is 2400 mm. The 3D printing figurine's chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS versions.


FFF/FDM 1.0 version features:
- Contains 27 parts;
- A printed model without wings is 365 mm tall, 210 mm wide, 193 mm deep;
- Ryuk assembled with wings is 379 mm tall, 307 mm wide, 222 mm deep;
- Assembly kit includes locks to connect parts without glue. One lock 21_ge_lock_7S(x5) needs to be printed 5 times; lock​ 22_ge_lock_10H(x12)​ needs to be printed 12 times;
- Ryuk can be assembled with wings or without them;
- Comes with a platform that has two large skulls mounted on it;
- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:
- Contains 10 parts;
- A printed model without wings is 183 mm tall, 105 mm wide, 97 mm deep;
- Ryuk assembled with wings is 189 mm tall, 153 mm wide, 111 mm deep;
- Ryuk can be assembled with wings or without them;
- Comes with a platform that has two large skulls mounted on it;
- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

DLP/SLA Eco 1.0 version features:
- Contains 10 parts;
- A printed model without wings is 183 mm tall, 105 mm wide, 97 mm deep;
- Ryuk assembled with wings is 189 mm tall, 153 mm wide, 111 mm deep;
- Ryuk can be assembled with wings or without them;
- Comes with a platform that has two large skulls mounted on it;
- Contains some hollowed out parts to save resin.

SLS 1.0 version features:
- Made as a solid one-piece figurine;
- A printed model without wings is 183 mm tall, 105 mm wide, 97 mm deep;
- Ryuk assembled with wings is 189 mm tall, 153 mm wide, 111 mm deep;
- Contains 2 parts - a one-piece Ryuk Shinigami model with wings and a figurine without wings.


- STL files of Ryuk 3D printing figurine which consist of 49 parts;
- 4 versions of files for this model for FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS;
- High-poly detailed figurine of Ryuk;
Assembly Manual for FFF/FDM 1.0 and DLP/SLA 1.0 versions in PDF format;
- Detailed settings that we provide as a recommendation for Cura 3.5.1, Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get Ryuk 3D printing figurine​ immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Ryuk 3D printing figurine at Gambody YouTube channel.

Also, you may like other Anime Figurines for 3D Printing.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.5.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for CuraSimplify3D and Slic3r softwares.

Cura printing recommendations:

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

To avoid printing problems, we recommend the following settings:

Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s 
     Support Infill Speed: 45 mm/s
Travel Speed: 45 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 45 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.6562 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 2.2 mm
Support Z Distance: 0.13 mm
    Support Top Distance: 0.13 mm
    Support Bottom Distance: 0.13 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 15 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Extruder 1 Temperature: 210
Heated Bed: 60

Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
  Detect thin walls: Check
  Detect bridging perimeters: Check
  Seam position: Random
  Fill desity: 20%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
  Infill/Perimeters overlap: 20%
  Bridge flow ratio: 0.95
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm


comments powered by Disqus

Similar items

Browse more newly listed 3D printings