Make pre-order

Getter-1 3D Printing Model | Assembly

(2)
average
cm: 46.2 w x 45.6 d x 36 h
in: 18.189 w x 17.953 d x 14.173 h
4
BUY FOR  $19.99

Source Files

|

Description

|

Printing Details

This 3D Model consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Getter-1 3D Printing Model comes in 4 versions for FFF/FDM and DLP/SLA/SLS 3D printers. Files for each version are available for download after purchase.

Detailed information about this 3D printing model is available in the DESCRIPTION section.

File Name File Size Time / Filament
1_head_FDM(repaired).stl
23.03 MiB 2 h 17 min
1 m
Download
2_horn_R_1_FDM(repaired). stl
5.55 MiB 53 min
<1 m
Download
3_horn_R_2_FDM(repaired). stl
2.30 MiB 8 min
<1 m
Download
4_horn_L_1_FDM(repaired). stl
6.25 MiB 53 min
<1 m
Download
5_horn_L_2_FDM(repaired). stl
2.32 MiB 8 min
<1 m
Download
6_body_FDM(repaired).stl
25.44 MiB 36 h 37 min
23 m
Download
7_pelvis_FDM(repaired).st l
21.77 MiB 13 h 18 min
8 m
Download
8_arm_R_1_FDM(repaired).s tl
13.59 MiB 5 h 9 min
3 m
Download
9_arm_R_2_FDM(repaired).s tl
13.20 MiB 4 h 25 min
3 m
Download
10_arm_L_1_FDM(repaired). stl
13.68 MiB 4 h 44 min
3 m
Download
11_arm_L_2_FDM(repaired). stl
14.23 MiB 6 h 19 min
4 m
Download
12_hand_R_FDM(repaired).s tl
8.62 MiB 2 h 58 min
2 m
Download
13_hand_L_FDM(repaired).s tl
8.49 MiB 2 h 58 min
2 m
Download
14_leg_R_1_FDM(repaired). stl
17.59 MiB 8 h 29 min
5 m
Download
15_leg_R_2_FDM(repaired). stl
15.69 MiB 12 h 19 min
7 m
Download
16_foot_R_FDM(repaired).s tl
18.04 MiB 5 h
3 m
Download
17_leg_L_1_FDM(repaired). stl
15.31 MiB 6 h 34 min
4 m
Download
18_leg_L_2_FDM(repaired). stl
16.93 MiB 16 h 6 min
10 m
Download
19_foot_L_FDM(repaired).s tl
15.98 MiB 5 h 12 min
3 m
Download
20_cloak_1_FDM(repaired). stl
16.28 MiB 20 h 24 min
12 m
Download
21_cloak_2_FDM(repaired). stl
15.69 MiB 27 h 20 min
16 m
Download
22_cloak_3_FDM(repaired). stl
18.98 MiB 64 h 29 min
56 m
Download
23_axe_1_FDM(repaired).st l
21.29 MiB 12 h 42 min
7 m
Download
24_axe_1_handle_FDM(repai red).stl
7.71 MiB 1 h 44 min
1 m
Download
25_axe_2_FDM(repaired).st l
20.40 MiB 12 h 36 min
7 m
Download
26_axe_2_handle_FDM(repai red).stl
7.36 MiB 1 h 51 min
1 m
Download
27_platform_1_FDM(repaire d).stl
15.56 MiB 23 h 58 min
14 m
Download
28_platform_2_FDM(repaire d).stl
15.20 MiB 23 h 54 min
14 m
Download
29_platform_3_FDM(repaire d).stl
17.88 MiB 30 h 14 min
17 m
Download
30_platform_4_FDM(repaire d).stl
19.46 MiB 23 h 54 min
14 m
Download
31_platform_5_FDM(repaire d).stl
16.68 MiB 25 h 51 min
15 m
Download
32_platform_6_FDM(repaire d).stl
12.36 MiB 16 h 38 min
10 m
Download
33_ge_lock_7S(x4)_FDM(rep aired).stl
0.02 MiB 3 min
<1 m
Download
34_ge_lock_10H(x27)_FDM(r epaired).stl
0.03 MiB 4 min
<1 m
Download
Keychain (repaired).stl
0.35 MiB 23 min
<1 m
Download
Tag (repaired).stl
1.70 MiB 1 h 16 min
1 m
Download

ABOUT THIS 3D MODEL

Getter-1 is the first and the most commonly used super robot combination of three different combat jets known as Eagle, Jaguar, and Bear within Getter Robo manga series. Originally created by Dr. Saotome for space exploration, the Getter Robo project instead became the main  defence force against the uprising Dinosaur Empire. When compared to the two other robot modes, Getter-1 is distinguished as the most balanced in both speed and combat as well as the one able to fight in almost any situation. Inspired by Go Nagai’s anime series, the author of the Getter-1 model for 3D printing spent 158 hours in total to prepare an eagle+jaguar+bear formation of the robot for all the cartoon fans to enjoy. Getter-1 robot for 3D printing is portrayed extremely furious - its stare is piercing and it seems that the ground is cracking under pressure of the mighty warrior. Naturally, the giant for 3D printing is equipped with the Getter Tomahawks and is actually depicted wielding two at a time. The cape-like attachment on the Getter-1’s back is known to help the robot fly and the mech’s remarkable Getter Wing was also not forgotten by the 3D artist. All fine details that would be dear for true anime enthusiasts such as blades on the robots forearms known as Getter Cutter or spikes on the head were also considered by the author of the model. It seems that once printed Getter-1 will also be able to fire Getter Rays! Go order the STL files to check it first.

ADAPTATION FOR 3D PRINTING

Getter-1 model for 3D printing is a static assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 48 hours in total. The model’s cutting was chosen by our team to minimise the amount of filament needed for generated support and some of the parts were hollowed out for you to save resin in the model’s Eco version. Moreover, in order to conceal the places where assembly parts of the robot must be connected, the model was cut along the contour of the Getter-1 armour seams. For you to achieve the cleanest 3D printed result, such finer details as “horns” and spikes on the robot’s head, the tomahawks’ grips and blades etc. are provided as separate assembly pieces. The model’s cloak called the Getter Wing was detached and split into three parts to ensure nice printing result and to fit even the smallest 3D printers’ build plates. All the assembly parts are provided in STL files in recommended positions that were worked out so to ensure the smoothness of the details’ surfaces after printing and that the 3D printing beginners won't face difficulties when placing the parts on a build plate. 

The model is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from Getter-1's actual height that is 38000 mm. The 3D printing model's chosen scale is 1/100 for the FFF/FDM version and 1/200 for the DLP/SLA/SLS versions.

VERSION SPECIFICATIONS

FFF/FDM 1.0 version features:
- Contains 34 parts;
- A printed model is 360 mm tall, 462 mm wide, 456 mm deep;
- Assembly kit includes locks to connect parts securely without glue. One lock 33_ge_lock_7S(x4) needs to be printed 4 times; lock 34_ge_lock_10H(x27) needs to be printed 27 times;
- Getter Tomahawks that are to be inserted into both robot's hands come separately;
- Made with a platform to resemble the grounds of a rocky battlefield;
- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:
- Contains 13 parts;
- A printed model is 180 mm tall, 231 mm wide, 228 mm deep;
- Made with a platform to resemble the grounds of a rocky battlefield;
- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

DLP/SLA Eco 1.0 version features:
- Contains 13 parts;
- A printed model is 180 mm tall, 231 mm wide, 228 mm deep;
- Made with a platform to resemble the grounds of a rocky battlefield; 
- Contains some hollowed out parts to save resin.

SLS 1.0 version features:
- Made as a solid one-piece figurine;
- A printed model is 180 mm tall, 231 mm wide, 228 mm deep;
- Contains 3 parts - a one-piece model and the robot with the platform separated.

WHAT WILL YOU GET AFTER PURCHASE?

- STL files of Getter-1​​​​ Model for 3D printing which consist of 63 parts;
- High-poly detailed model of Getter-1​​​;
- Detailed settings that we provide as a recommendation for Cura 3.5.1, Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get the model of Getter-1​ for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Getter-1​​ 3D Printing Model at Gambody YouTube channel.

Also, you may like another Robot 3D Printing Models as well as other Anime 3D Printing Figurines.

_______
FAQ: 

Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.4.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for CuraSimplify3D and Slic3r softwares.

Cura printing recommendations:

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

To avoid printing problems, we recommend the following settings:

Quality
Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Shell
Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill
Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Material
Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s

Speed 
Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
Travel Speed: 45 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 30 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Travel 
Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Cooling 
Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100%
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Support 
Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 50°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 3 mm
Support Z Distance: 0.1 mm
    Support Top Distance: 0.1 mm
    Support Bottom Distance: 0.1 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65°

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 18
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Experimental
Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Extruder
Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Layer
Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Additions
Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Infill
Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Support
Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Temperature
Extruder 1 Temperature: 210
Heated Bed: 60

Cooling
Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Speeds
Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Other
Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
Quality
  Detect thin walls: Check
  Detect bridging perimeters: Check
Advanced
  Seam position: Random
Infill
  Fill desity: 20%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
Advanced
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
Skirt
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
Brim 
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
Raft
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
Modifiers
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
Autospeed
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
Overlap
  Infill/Perimeters overlap: 20%
Flow
  Bridge flow ratio: 0.95
Other
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm

Comments

comments powered by Disqus
Other author's 3D printings

Tags

Getter-1, Getter Robo, Manga, Anime, Cartoon, Robot, Japan, Assembly, Mecha

Similar items

Browse more newly listed 3D printings