Make pre-order

(3)
average
cm: 11 w x 5.4 d x 25 h
in: 4.331 w x 2.126 d x 9.843 h
4
BUY FOR  $24.99

Source Files

|

Description

|

Printing Details

This 3D Model consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Mazinger Z 3D Printing Model comes in 1 version for FFF/FDM 3D printers. STL files of the version are available for download after the purchase.

Detailed information about this 3D printing model is available in the DESCRIPTION section.

File Name File Size Time / Filament
1_head (repaired).stl
1.39 MiB 1 h 33 min
1 m
Download
2_collo (repaired).stl
0.29 MiB 19 min
<1 m
Download
3_perno_collo1 (repaired) .stl
0.69 MiB 13 min
<1 m
Download
4_Shoulder1_R (repaired). stl
0.16 MiB 35 min
<1 m
Download
5_Shoulder2_R (repaired). stl
0.14 MiB 34 min
<1 m
Download
6_Upper arm_R (repaired). stl
0.24 MiB 51 min
<1 m
Download
7_Upper arm2_R (repaired) .stl
0.22 MiB 30 min
<1 m
Download
8_Upper arm3_R (repaired) .stl
0.02 MiB 8 min
<1 m
Download
9_Upper arm4_R (repaired) .stl
0.45 MiB 19 min
<1 m
Download
10_Upper arm5_R (repaired ).stl
0.97 MiB 21 min
<1 m
Download
11_Arm_R (repaired).stl
0.73 MiB 1 h 58 min
1 m
Download
12_Hand1_R (repaired).stl
1.38 MiB 34 min
<1 m
Download
13_Hand2_R (repaired).stl
0.06 MiB 13 min
<1 m
Download
14_Hand3_R (repaired).stl
0.40 MiB 4 min
<1 m
Download
15_Hand4_R (repaired).stl
0.39 MiB 5 min
<1 m
Download
16_Hand5_R (repaired).stl
0.40 MiB 4 min
<1 m
Download
17_Hand6_R (repaired).stl
0.41 MiB 4 min
<1 m
Download
18_Shoulder1_L (repaired) .stl
0.16 MiB 35 min
<1 m
Download
19_Shoulder2_L (repaired) .stl
0.14 MiB 34 min
<1 m
Download
20_Upper arm_L (repaired) .stl
0.24 MiB 51 min
<1 m
Download
21_Upper arm2_L (repaired ).stl
0.22 MiB 30 min
<1 m
Download
22_Upper arm3_L (repaired ).stl
0.02 MiB 8 min
<1 m
Download
23_Upper arm4_L (repaired ).stl
0.45 MiB 19 min
<1 m
Download
24_Upper arm5_L (repaired ).stl
0.97 MiB 21 min
<1 m
Download
25_Arm_L (repaired).stl
0.73 MiB 1 h 58 min
1 m
Download
26_Hand1_L (repaired).stl
1.38 MiB 34 min
<1 m
Download
27_Hand2_L (repaired).stl
0.06 MiB 13 min
<1 m
Download
28_Hand3_L (repaired).stl
0.40 MiB 5 min
<1 m
Download
29_Hand4_L (repaired).stl
0.39 MiB 5 min
<1 m
Download
30_Hand5_L (repaired).stl
0.40 MiB 4 min
<1 m
Download
31_Hand6_L (repaired).stl
0.41 MiB 4 min
<1 m
Download
32_boomerang (repaired).s tl
0.08 MiB 1 h 19 min
1 m
Download
33_missile door (repaired ).stl
0.23 MiB 25 min
<1 m
Download
34_Hip_joint (repaired).s tl
1.40 MiB 20 min
<1 m
Download
35_Shoulder_joint_x2 (rep aired).stl
0.16 MiB 26 min
<1 m
Download
36_Torso_joints_x2 (repai red).stl
0.68 MiB 13 min
<1 m
Download
37_Torso1 (repaired).stl
6.18 MiB 3 h 17 min
2 m
Download
38_Torso2 (repaired).stl
4.16 MiB 3 h 7 min
2 m
Download
39_Torso3 (repaired).stl
1.41 MiB 1 h 54 min
1 m
Download
40_Torso4 (repaired).stl
1.57 MiB 1 h 39 min
1 m
Download
41_Torso5 (repaired).stl
1.00 MiB 2 h 36 min
2 m
Download
42_hp1 (repaired).stl
1.13 MiB 31 min
<1 m
Download
43_hp2 (repaired).stl
0.07 MiB 5 min
<1 m
Download
44_hp3 (repaired).stl
0.08 MiB 5 min
<1 m
Download
45_Upper leg1_R (repaired ).stl
1.06 MiB 1 h 13 min
1 m
Download
46_Upper leg2_R (repaired ).stl
1.12 MiB 1 h 13 min
1 m
Download
47_Knee1_R (repaired).stl
0.04 MiB 37 min
<1 m
Download
48_Knee2_R (repaired).stl
0.04 MiB 10 min
<1 m
Download
49_Knee3_R (repaired).stl
0.09 MiB 27 min
<1 m
Download
50_Ankle joint_R (repaire d).stl
0.68 MiB 13 min
<1 m
Download
51_Leg1_R (repaired).stl
1.34 MiB 2 h 44 min
2 m
Download
52_Leg2_R (repaired).stl
1.41 MiB 3 h 16 min
2 m
Download
53_Foot_R (repaired).stl
0.91 MiB 1 h 56 min
1 m
Download
54_Upper leg1_L (repaired ).stl
1.12 MiB 1 h 13 min
1 m
Download
55_Upper leg2_L (repaired ).stl
1.11 MiB 1 h 14 min
1 m
Download
56_Knee1_L (repaired).stl
0.04 MiB 37 min
<1 m
Download
57_Knee2_L (repaired).stl
0.04 MiB 10 min
<1 m
Download
58_Knee3_L (repaired).stl
0.09 MiB 27 min
<1 m
Download
59_Ankle joint_L (repaire d).stl
0.68 MiB 13 min
<1 m
Download
60_Leg1_L (repaired).stl
1.34 MiB 2 h 44 min
2 m
Download
61_Leg2_L (repaired).stl
1.41 MiB 3 h 16 min
2 m
Download
62_Foot_L (repaired).stl
0.91 MiB 1 h 56 min
1 m
Download
Keychain (repaired).stl
0.35 MiB 23 min
<1 m
Download
Tag (repaired).stl
1.70 MiB 1 h 16 min
1 m
Download

ABOUT THIS 3D MODEL

Mazinger Z is credited as the first piloted giant robot, the titular mech of Mazinger Z Japanese manga series. The titanic robot was constructed by Doctor Juzo Kabuto using newly-discovered hyper-alloy “Super Alloy Z”. With the main element of the metal alloy being fictional Japanium that is noted to be even stronger than steel, the mech can boast of extremely high durability. Creation of Mazinger Z robot within the series of the same name is considered to mark the launch of the Super Robot genre into existence. The author of the model spent 160 hours to design and engineer the awesome 3D printing model to rejoice the anime television series fans. And Mazinger Z will definitely become a gem in your 3D printed collection - thanks to the 3D artist’s hard work and creative approach the robot is fully articulated! The Japanese super robot is depicted as it appears in the original 1972 series - with large fins on the chest to enable its Photonic Energy reactor and the control centre Hover Pilder to host the pilot. The giant mech is an excellent ally to fight the evil especially given that conventional weapons can affect its armour even not in the slightest.

ADAPTATION FOR 3D PRINTING

Mazinger Z model for 3D printing is a highly articulated assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 32 hours in total. In order to ensure the robot’s multidirectional movement, it was divided into many assembly parts and all model’s joints were designed to presuppose the introduction of a certain mechanism to give you an opportunity to display Mazinger Z in a variety of positions, i.e. robot’s head, shoulders, arms, elbows, hands, hips, knees, feet and even fingers are movable. The Breast fire fins on Mazinger Z's chest are also provided as a separate file for you to receive the cleanest printed result. All the assembly parts are provided in STL files in recommended positions that were worked out so to ensure the smoothness of the details’ surfaces after printing and so that the 3D printing beginners won't face difficulties when placing the parts on a build plate. In order to assemble the model, you will need 2x14 mm self-tapping screws and short pieces of 1.75 PLA to make pins. Apply the glue where you feel appropriate. Make sure to watch "Assembly video" in the photo preview section and read the author's "Assembly Manual" that comes with STL files.

The model is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from Mazinger Z's actual height that is 18000 mm. The 3D printing model's chosen scale is 1/72 for the FFF/FDM version.

VERSION SPECIFICATIONS

FFF/FDM 1.0 version features:
- Contains 62 parts;
- A printed model is 250 mm tall, 110 mm wide, 54 mm deep;
- Each robot’s joint is articulated which allows the model's movability;
- The model can be assembled with 1.75 PLA pins and 2x14 mm screws;
- Watch "Assembly video" to see the screws coloured red and pins - yellow; 
- With any file of the model, you will also receive author’s instructions on the assembly peculiarities in a PDF file "Assembly Manual";
- All parts are divided in such a way that you will print them with the smallest number of support structures.

WHAT WILL YOU GET AFTER PURCHASE?

- STL files of Mazinger Z​​ Model for 3D printing which consist of 62 parts;
- High-poly detailed model of Mazinger Z;
- Detailed settings that we provide as a recommendation for Cura 3.5.1, Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get the model of Mazinger Z​ for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Mazinger Z​ 3D Printing Model at Gambody YouTube channel.

Also, you may like another Robot 3D Printing Models as well as other Anime 3D Printing Figurines.

_______
FAQ: 

Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.4.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for CuraSimplify3D and Slic3r softwares.

Cura printing recommendations:

Recommendations: Use ABS or PLA Plus filament to print more durable and friction resistant details.

To avoid printing problems, we recommend the following settings:

Quality
Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Shell
Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill
Infill Density: 80%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Material
Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s

Speed 
Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
Travel Speed: 45 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 30 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Travel 
Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Cooling 
Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100%
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Support 
Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 50°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 3 mm
Support Z Distance: 0.1 mm
    Support Top Distance: 0.1 mm
    Support Bottom Distance: 0.1 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65°

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 18
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Experimental
Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Extruder
Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Layer
Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Additions
Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Infill
Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 80%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Support
Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Temperature
Extruder 1 Temperature: 210
Heated Bed: 60

Cooling
Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Speeds
Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Other
Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
Quality
  Detect thin walls: Check
  Detect bridging perimeters: Check
Advanced
  Seam position: Random
Infill
  Fill density: 80%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
Advanced
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
Skirt
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
Brim 
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
Raft
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
Modifiers
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
Autospeed
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
Overlap
  Infill/Perimeters overlap: 20%
Flow
  Bridge flow ratio: 0.95
Other
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm

Comments

comments powered by Disqus
Other author's 3D printings

Tags

robot, mech, transformer, mazinger z, anime, manga, action, assembly

Similar items

Browse more newly listed 3D printings