Make pre-order

Titan Redeemer 3D Printing Model | Assembly+Action

cm: 20.7 w x 8.6 d x 28 h
in: 8.15 w x 3.386 d x 11.024 h

Source Files




Printing Details

This 3D Miniature consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Version 1, Version 2 and Version 3 for Titan Redeemer 3D Model optimized for 3D printing, the preview pictures of which you see above.

It is recommended:

  • to print Version 1 STL files on FDM/FFF 3D printers;
  • to print Version 2 STL files on DLP/SLA 3D printers.
  • to print Version 3 STL files on SLS 3D printers.
File Name File Size Time / Filament Object Size
(x/y/z mm)
4.33 MiB 5 h 45 min
3 m
37 x 48 x 70 Download
2_B_Claw (x2).stl
0.16 MiB 17 min
<1 m
18 x 23 x 10 Download
3_Axis_2_B_Joint (x2).stl
0.35 MiB 22 min
<1 m
15 x 15 x 23 Download
13.60 MiB 10 h 29 min
6 m
45 x 51 x 62 Download
4.34 MiB 5 h 43 min
3 m
37 x 48 x 70 Download
12.51 MiB 30 min
<1 m
39 x 24 x 23 Download
12.51 MiB 30 min
<1 m
39 x 24 x 23 Download
8_claw_1 (x2).stl
0.04 MiB 7 min
<1 m
8 x 19 x 6 Download
30.29 MiB 26 h 44 min
17 m
131 x 68 x 75 Download
1.54 MiB 1 h 45 min
1 m
28 x 29 x 35 Download
11_Axis_2_AA_Basket (x2). stl
1.38 MiB 11 min
<1 m
13 x 13 x 9 Download
0.97 MiB 25 min
<1 m
22 x 12 x 21 Download
12.95 MiB 31 min
<1 m
42 x 15 x 23 Download
12.95 MiB 31 min
<1 m
42 x 15 x 23 Download
3.68 MiB 2 h 25 min
1 m
22 x 31 x 51 Download
0.71 MiB 19 min
<1 m
9 x 9 x 23 Download
2.43 MiB 2 h 2 min
1 m
30 x 31 x 39 Download
12.83 MiB 9 h 15 min
5 m
63 x 65 x 55 Download
2.41 MiB 2 h 3 min
1 m
30 x 31 x 39 Download
20_claw_3 (x4).stl
0.08 MiB 10 min
<1 m
19 x 11 x 8 Download
8.84 MiB 3 h 4 min
2 m
36 x 30 x 50 Download
5.02 MiB 3 h 51 min
2 m
39 x 30 x 70 Download
23_A_Claw (x4).stl
0.31 MiB 9 min
<1 m
14 x 24 x 7 Download
24_Axis_2_A_Joint (x4).st l
0.28 MiB 24 min
<1 m
11 x 11 x 27 Download
25_claw_2 (x4).stl
0.07 MiB 6 min
<1 m
8 x 16 x 6 Download
1.21 MiB 1 h 1 min
1 m
24 x 22 x 32 Download
1.21 MiB 1 h 1 min
1 m
24 x 22 x 32 Download
28_Ge_lock_7S (x4).stl
0.02 MiB 3 min
<1 m
7 x 18 x 2 Download
10.74 MiB 4 h 47 min
3 m
29 x 49 x 73 Download
10.76 MiB 4 h 53 min
3 m
29 x 49 x 73 Download
1.19 MiB 3 h 53 min
2 m
53 x 79 x 35 Download
1.19 MiB 3 h 53 min
2 m
53 x 79 x 35 Download


Titan Redeemer is a Mark-6 Jaeger. During the construction of Titan Redeemer, its design was constructed to account for the imbalance created by the M19 Morning Star. Titan Redeemer’s upper body frame is broad and T-framed, which is meant to offset the weight created by the Morning Star which substitutes for a hand. The M19 Morning Star creates a seismic effect, and its secondary weapon, the EMP Mist Grenade can disrupt electrical signals. Titan Redeemer is powered by a GG-11 Gyro Core and is equipped with T-21 “Flatfoot” Sentry Treats for its feet. It's M-19 Morning Star weapon was later retrofitted to Bracer Phoenix.


The model is saved in STL files, a format supported by most 3D printers

FDM version features:
- Contain 32 parts;
- Made with Locks for better fixing. One part of Lock (28_Ge_lock_7S (x4)) you need to print 4 times.
- Made with Claws and Joints for saving all movable details as in original robot.
- One part of Twin Claw (20_claw_3 (x4)) you need to print 4 times.
- One part of Claw (23_A_Claw (x4)) you need to print 4 times.
- One part of Joint (24_Axis_2_A_Joint (x4)) you need to print 4 times.
- One part of Claw_v1 (8_claw_1 (x2)) you need to print twice.
- One part of Claw_v2 (25_claw_2 (x4)) you need to print 4 times.
- One part of Claw_B (2_B_Claw (x2)) you need to print twice;
- One part of Joint_B (3_Axis_2_B_Joint (x2)) you need to print twice;
- One part of Basket (11_Axis_2_AA_Basket (x2)) you need to print twice;
- All parts are divided in such way that you will print them with the smallest amount of supports.

DLP/SLA version features:
- Same as FDM but smaller, also made as 7 parts;

SLS version features:
- Same as SLA but made as 1 part for economy your material;

All STL files for 3D printing have been checked in Netfabb and no errors were shown.

Note: Before starting 3D printing the model, read the Printing Details for CURA 3.2.1. Software.

There are 32 parts for FFF/FDM version, 7 parts for SLA version and 1 parts for SLS.

Scale: Its height is 55700 mm. The scale of this model made in proportion to it. 1/200 for FDM version and 1/400 for DLP/SLS/SLA version.

FDM version dimensions:
After being printed will stand - 280 mm tall, 207 mm wide, 86 mm deep;

SLS/DLP/​SLA version dimensions:
After being printed will stand - 140 mm tall, 104 mm wide, 43 mm deep;
- Has a few details, to keep printing costs down.


- STL files of Titan Redeemer​ 3D Model for 3D printing which consist of 40 parts;
- 3 versions of files for this model for FFF/FDM, DLP/SLA and for SLS 3D printers;
- Made with saving all movable elements
- Model fixed by the Locks, Joints, and Claws;
- High-poly detailed model of Titan Redeemer​;
- Detailed settings that we provide for Cura 3.2.1. and Simplify3D for the best print;
- Full technical support from the Gambody Support Team.

Watch the tutorial video on how to assemble Titan Redeemer​ 3D Printing Model at Gambody YouTube channel.

You can get Model of Titan Redeemer​ for 3D Printing right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Also, you may like other Jaegers 3D Printing Models.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.2.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for Cura and Simplify3D softwares.

Cura printing recommendations:

Recommendations: For all parts of Locks and Claws you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

To avoid printing problems, we recommend the following settings:

Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Print Speed: 45 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
Travel Speed: 120 mm/s
Initial Layer Speed: 30 mm/s
  Initial Layer Print Speed: 30 mm/s
  Initial Layer Travel Speed: 60 mm/s
Skirt/Brim Speed: 30 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 1.3333 mm
Support Z Distance: 0.3 mm
    Support Top Distance: 0.3 mm
    Support Bottom Distance: 0.3 mm
Support X/Y Distance: 0.7 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.2 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 18 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.


Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Extruder 1 Temperature: 210
Heated Bed: 60

Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Unsupported area threshold: 20.0 sq m


Similar items

Browse more newly listed 3D printings