Make pre-order

Nick Fury & Cat 3D Printing Figurines in Diorama | Assembly

(3)
average
cm: 12.3 w x 14 d x 24.4 h
in: 4.843 w x 5.512 d x 9.606 h
4
BUY FOR  $24.99

Source Files

|

Description

|

Printing Details

This 3D Figurine consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Nick Fury & Cat 3D Printing Figurines in Diorama come in 4 versions for each 3D printer type (FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS). Files for each version are available for download after the purchase.

Detailed information about this 3D printing figurine is available in the DESCRIPTION section.

File Name File Size Time / Filament
1_head_FDM(repaired).stl
27.69 MiB 1 h 48 min
1 m
Download
2_body_FDM(repaired).stl
28.70 MiB 10 h 45 min
6 m
Download
3_legs_FDM(repaired).stl
27.70 MiB 7 h 18 min
4 m
Download
4_arm_R_1_FDM(repaired).s tl
7.94 MiB 1 h 21 min
1 m
Download
5_arm_R_2_FDM(repaired).s tl
8.41 MiB 34 min
<1 m
Download
6_hand_R_FDM(repaired).st l
6.48 MiB 22 min
<1 m
Download
7_arm_L_1_FDM(repaired).s tl
8.84 MiB 1 h 2 min
1 m
Download
8_arm_L_2_FDM(repaired).s tl
7.19 MiB 50 min
<1 m
Download
9_hand_L_FDM(repaired).st l
8.12 MiB 24 min
<1 m
Download
10_foot_R_FDM(repaired).s tl
9.96 MiB 33 min
<1 m
Download
11_foot_L_FDM(repaired).s tl
10.34 MiB 33 min
<1 m
Download
12_cat_body_FDM(repaired) .stl
25.26 MiB 3 h 48 min
2 m
Download
13_paw_R_FDM(repaired).st l
19.67 MiB 20 min
<1 m
Download
14_paw_L_FDM(repaired).st l
13.47 MiB 11 min
<1 m
Download
15_cat_head_1_FDM(repaire d).stl
15.62 MiB 32 min
<1 m
Download
16_cat_head_2_FDM(repaire d).stl
16.88 MiB 1 h 17 min
1 m
Download
17_tentacle_1_FDM(repaire d).stl
2.79 MiB 31 min
<1 m
Download
18_tentacle_2_FDM(repaire d).stl
3.00 MiB 34 min
<1 m
Download
19_tentacle_3_FDM(repaire d).stl
4.16 MiB 21 min
<1 m
Download
20_tentacle_4_FDM(repaire d).stl
5.30 MiB 33 min
<1 m
Download
21_tentacle_5_FDM(repaire d).stl
4.19 MiB 34 min
<1 m
Download
22_tentacle_6_FDM(repaire d).stl
2.96 MiB 50 min
<1 m
Download
23_platform_FDM(repaired) .stl
20.06 MiB 9 h 52 min
5 m
Download
24_ge_lock_10H(x1)_FDM(re paired).stl
0.03 MiB 4 min
<1 m
Download
Keychain (repaired).stl
0.35 MiB 23 min
<1 m
Download
Tag (repaired).stl
1.70 MiB 1 h 16 min
1 m
Download

ABOUT THIS 3D FIGURINE

Nick Fury and his adorable affection towards the orange tabby Goose made the way into all the MCU fans’ hearts once the Captain Marvel movie was released on a big screen and the author of this 3D printing diorama is no exception! Who would have thought that serious and pragmatic Nick Fury was a cat person? Moreover, the origin of Fury’s mysterious eye injury was finally revealed! Rather than losing an eye in some insanely dangerous heroic adventure, the person behind the Avengers Initiative got scratched in the face by his new furry cat friend. The scene-stealing duo was such a huge and amusing part of Captain Marvel movie that the author of the figurines for 3D printing decided to sculpt both Nick Fury and Goose the Cat with her two alternative appearances and spent 109 hours in total to complete the project. While Goose does look like a cat, she's actually a cat-like alien called a Flerken who has a pocket dimension inside her body where she stores massive tentacles. The 3D artist depicted the stunned Nick Fury holding the cat who suddenly revealed her Flerken powers and easily swallowed the Tesseract much to her owner’s surprise. The author provided Goose the Cat with her two alternative head variants - the cat-like one and with long Flerken tentacles extended from the mouth. Tabby did permanently blind Fury and though now the S.H.I.E.L.D. agent has to be secretive about the far from exciting origin of his eye-patch, the 3D printing diorama is too cool not to acquire for one’s Marvel figurines collection. 

ADAPTATION FOR 3D PRINTING

Nick Fury & Cat figurines in diorama for 3D printing are static assembly models and the diorama’s moderation and adaptation for different types of 3D printers took Gambody team 21 hours in total. The anatomy of both figurines was thoroughly reviewed in the course of moderation process for the duo to be proportionally depicted in the intended pose. The models' cutting was chosen by our team to minimise the amount of filament needed for generated support and some of the diorama's parts were hollowed out for you to save resin. Moreover, in order to conceal the places where the assembly parts of the figurines must be connected, the cutting was made along the contour of the Nick Fury clothes' seams and each Goose's tentacle is provided separately to receive the fine details of the best quality. The cat's head is cut in such a way for you to be able to change the alien's appearance whenever you want. All the assembly parts are provided in STL files in recommended positions that were worked out so to ensure the smoothness of the details’ surfaces after printing and that the 3D printing beginners won't face difficulties when placing the parts on a build plate. 

The figurine is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from Nick Fury's actual height that is 1850 mm. The 3D printing figurine's chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS versions.

VERSIONS' SPECIFICATIONS

FFF/FDM 1.0 version features:
- Contains 24 parts;
- A printed model is 244 mm tall, 123 mm wide, 140 mm deep;
- Assembly kit includes one lock to connect Nick Fury's body and legs securely without glue;
- Made with a platform with S.H.I.E.L.D.'s coat of arms design;
- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:
- Contains 8 parts;
- A printed model is 122 mm tall, 62 mm wide, 70 mm deep;
- Made with a platform with S.H.I.E.L.D.'s coat of arms design;
- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

DLP/SLA Eco 1.0 version features:
- Contains 8 parts;
- A printed model is 122 mm tall, 62 mm wide, 70 mm deep;
- Made with a platform with S.H.I.E.L.D.'s coat of arms design;
- Contains some hollowed out parts to save resin.

SLS 1.0 version features:
- Made as solid one-piece figurines;
- A printed model is 122 mm tall, 62 mm wide, 70 mm deep;
- Contains 5 parts - one-piece diorama in two Goose variants and two versions of figurines with the platform separated.

WHAT WILL YOU GET AFTER PURCHASE?

- STL files of Nick Fury & Cat 3D Printing Figurines in Diorama for 3D printing which consist of 45 parts;
- 4 versions of files for this model for FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS;
- High-poly detailed figurines of Nick Fury & Cat;
- Detailed settings that we provide as a recommendation for Cura 3.5.1, Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get the figurines of Nick Fury & Cat for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Nick Fury & Cat 3D Printing Figurines in Diorama at Gambody YouTube channel.

Also, you may like Carol Danvers figurine for 3D printing as well as other Marvel 3D Printing Figurines.

_______
FAQ: 

Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.5.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for CuraSimplify3D and Slic3r softwares.

Cura printing recommendations:

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

To avoid printing problems, we recommend the following settings:

Quality
Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Shell 
Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill 
Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Material 
Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Speed 
Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s 
     Support Infill Speed: 45 mm/s
Travel Speed: 45 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 45 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Travel 
Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.6562 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Cooling 
Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Support 
Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 2.2 mm
Support Z Distance: 0.13 mm
    Support Top Distance: 0.13 mm
    Support Bottom Distance: 0.13 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 15 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Experimental
Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Extruder
Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Layer
Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Additions
Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Infill
Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Support
Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Temperature
Extruder 1 Temperature: 210
Heated Bed: 60

Cooling
Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Speeds
Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Other
Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
Quality
  Detect thin walls: Check
  Detect bridging perimeters: Check
Advanced
  Seam position: Random
Infill
  Fill desity: 20%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
Advanced
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
Skirt
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
Brim 
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
Raft
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
Modifiers
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
Autospeed
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
Overlap
  Infill/Perimeters overlap: 20%
Flow
  Bridge flow ratio: 0.95
Other
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm

Comments

comments powered by Disqus
Other author's 3D printings

Tags

Nick Fury, Captain Marvel, heroes, comics, assembly, avengers, shield, flerken

Similar items

Browse more newly listed 3D printings