Make pre-order

Paladin Judgement Armor 3D Printing Figurine | Assembly

cm: 16.1 w x 20.5 d x 25.2 h
in: 6.339 w x 8.071 d x 9.921 h
BUY FOR  $24.99

Source Files




Printing Details

This 3D Figurine consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Paladin Judgement Armor 3D Printing Figurine comes in 4 versions for each 3D printer type (FFF/FDM, DLP/SLA and SLS). Files for each version are available for download after the purchase.

Detailed information about this 3D printing figurine is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
52.18 MiB 26 h 40 min
16 m
59.66 MiB 34 h 7 min
20 m
3_arm_R_1_FDM(repaired).s tl
23.32 MiB 1 h 53 min
1 m
28 x 33 x 41 Download
4_arm_R_2_FDM(repaired).s tl
26.02 MiB 1 h 60 min
1 m
43 x 28 x 37 Download
5_hand_R_FDM(repaired).st l
15.82 MiB 43 min
<1 m
19 x 19 x 34 Download
6_arm_L_1_FDM(repaired).s tl
22.62 MiB 1 h 58 min
1 m
29 x 34 x 36 Download
7_arm_L_2_FDM(repaired).s tl
21.69 MiB 2 h 13 min
1 m
45 x 27 x 41 Download
8_hand_L_FDM(repaired).st l
15.81 MiB 53 min
<1 m
19 x 22 x 30 Download
9_foot_R_FDM(repaired).st l
38.54 MiB 3 h 41 min
2 m
32 x 39 x 54 Download
10_foot_L_FDM(repaired).s tl
35.93 MiB 3 h 5 min
2 m
27 x 45 x 56 Download
11_scapular_R_FDM(repaire d).stl
43.27 MiB 7 h 30 min
4 m
60 x 77 x 47 Download
12_scapular_L_FDM(repaire d).stl
36.07 MiB 6 h 23 min
4 m
52 x 73 x 45 Download
13_armor_front_FDM(repair ed).stl
14.38 MiB 51 min
1 m
30 x 32 x 13 Download
14_armor_back_FDM(repaire d).stl
17.24 MiB 3 h 9 min
2 m
15_knee_pad_R_FDM(repaire d).stl
32.74 MiB 50 min
<1 m
26 x 24 x 15 Download
16_knee_pad_L_FDM(repaire d).stl
17.02 MiB 47 min
<1 m
25 x 26 x 15 Download
17_armor_stripes_1_FDM (r epaired).stl
21.94 MiB 2 h 47 min
2 m
29 x 32 x 97 Download
18_armor_stripes_2_FDM (r epaired).stl
15.31 MiB 3 h 20 min
2 m
30 x 25 x 96 Download
19_armor_stripes_3_FDM (r epaired).stl
15.81 MiB 5 h 12 min
3 m
56 x 35 x 99 Download
20_armor_stripes_4_FDM (r epaired).stl
17.80 MiB 5 h 1 min
3 m
34 x 37 x 98 Download
21_armor_stripes_5_FDM (r epaired).stl
10.91 MiB 1 h 40 min
1 m
13 x 19 x 93 Download
22_hammer_1_FDM(repaired) .stl
20.54 MiB 3 h 13 min
2 m
23_hammer_2_FDM(repaired) .stl
19.80 MiB 3 h 18 min
2 m
31 x 32 x 42 Download
24_hammer_3_FDM(repaired) .stl
20.44 MiB 3 h 15 min
2 m
31 x 32 x 42 Download
25_hammer_4_FDM(repaired) .stl
8.87 MiB 2 h 31 min
2 m
18 x 19 x 96 Download
26_sword_FDM(repaired).st l
23.57 MiB 4 h 47 min
3 m
13 x 133 x 45 Download
27_sword_handle_FDM(repai red).stl
10.35 MiB 1 h 20 min
1 m
17 x 22 x 74 Download
28_arrow_1_FDM(repaired). stl
2.98 MiB 19 min
<1 m
12 x 70 x 9 Download
29_arrow_2_FDM(repaired). stl
2.68 MiB 17 min
<1 m
12 x 63 x 10 Download
30_arrow_3_FDM(repaired). stl
2.62 MiB 19 min
<1 m
12 x 70 x 10 Download
31_arrow_4_FDM(repaired). stl
3.02 MiB 19 min
<1 m
12 x 70 x 10 Download
32_arrow_5_FDM(repaired). stl
3.05 MiB 19 min
<1 m
12 x 70 x 10 Download
33_platform_FDM(repaired) .stl
60.31 MiB 30 h 42 min
17 m
161 x 160 x 56 Download
34_ge_lock_7S(x2)_FDM (re paired).stl
0.02 MiB 3 min
<1 m
18 x 7 x 2 Download
35_ge_lock_10H(x3)_FDM (r epaired).stl
0.03 MiB 4 min
<1 m
10 x 18 x 2 Download
Keychain (repaired).stl
0.35 MiB 23 min
<1 m
30 x 30 x 2 Download
Tag (repaired).stl
1.70 MiB 1 h 16 min
1 m
150 x 18 x 5 Download
26_1_sword_FDM(repaired). stl
34.09 MiB 5 h 7 min
3 m


The Paladin is the powerful class in WoW with the ability to perform three major in-game roles - healing, protection, and damage. As it is clear from the title of the 3D printing model, the author of the Paladin Judgement Armor figurine decided to go for a Tier 2 Set that can be obtained in the course of the World of Warcraft game. The 3D artist mentioned that the idea behind his sculpt was to present a mix of "in-game" and realistic armor design. The whole project took the author approximately 170 hours and resulted in an excellent warrior for one’s 3D printed Alliance collection. Paladin figurine for 3D printing is depicted wearing the Judgement Armor in its all glory! The author of the model paid careful attention to outlining the patterns on the warrior’s massive belt, bindings, chest, and legplates, etc. Paladin’s large structured hood partially conceals the highly-detailed helmet. We recommend that you take a closer look at the incredible details of the Judgement Armor’s spaulders. The 3D artist made sure to include the finest letters on the pages of the opened book, while the decorative swords have deep scratches and intricate engravings. Paladin Judgement Armor 3D printing figurine comes with two interchangeable weapons so the model can be displayed wielding either the Paladin Hammer or the Ashbringer Sword. Last but not least, the platform that the figurine comes with is made to depict the warrior as if in the middle of the battlefield. The base is studded with arrows and is adorned with a helmet of the fallen enemy. The mighty holy knight is perfectly ready to join your 3D printing army!  


Paladin Judgement Armor figurine for 3D printing is a static assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 38 hours in total. The figurine’s anatomy and proportions were thoroughly reviewed during the moderation process for the bulky armor to be depicted harmoniously the intended pose. The model’s cutting was chosen by our team to minimise the amount of filament needed for generated support and some of the parts were hollowed out for you to save resin in the figurine’s Eco version. In order to conceal the places where the assembly parts of the model must be connected, the figurine was cut along the contour of the Paladin’s armor seams. For you to achieve the cleanest 3D printed result, Paladin’s massive Judgement Spaulders, Bindings, Breastplate, cloth fragments, hands, etc. are provided as separate assembly parts. Moreover, to ensure the convenient assembly of the figurine, Paladin’s Hammer and Ashbringer sword were split as well. All the assembly parts come in STL files in recommended positions that were worked out in order to ensure the smoothness of the details’ surfaces after printing and so that the 3D printing beginners won't face difficulties when placing the parts on a build plate. When downloading any figurine's file you will also receive "Assembly Manual" for FFF/FDM 1.0 and DLP/SLA 1.0 versions in PDF format.

The figurine is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from the average height of male characters in WoW which is 1850 mm. The 3D printing figurine's chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS versions.


FFF/FDM 1.0 version features:
- Contains 35 parts;
- A printed model is 252 mm tall, 161 mm wide, 205 mm deep;
- Assembly kit includes locks to attach the figurine's parts securely without glue. Lock 34_ge_lock_7S(x2) needs to be printed twice, lock 35_ge_lock_10H(x3) needs to be printed 3 times;
- Comes on a platform studded with arrows;
- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:
- Contains 13 parts;
- A printed model is 126 mm tall, 81 mm wide, 103 mm deep;
- Comes on a platform studded with arrows;
- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

DLP/SLA Eco 1.0 version features:
- Contains 13 parts;
- A printed model is 126 mm tall, 81 mm wide, 103 mm deep;
- Comes on a platform studded with arrows;
- Contains some hollowed out parts to save resin.

SLS 1.0 version features:
- Made as a solid one-piece figurine;
- A printed model is 126 mm tall, 81 mm wide, 103 mm deep;
- Contains 5 parts - a one-piece model wielding  and the figurine with the platform separated.


- STL files of Paladin Judgement Armor 3D Figurine for 3D printing which consist of 66 parts;
- 4 versions of files for this model for FFF/FDM, DLP/SLA, DLP/SLA Eco and SLS;
- High-poly detailed figurine of Paladin Judgement Armor;
Assembly Manual for FFF/FDM 1.0 and DLP/SLA 1.0 versions in PDF format;
- Detailed settings that we provide as a recommendation for Cura 3.5.1, Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get the figurine of Paladin Judgement Armor​​​​​​​ for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Paladin Judgement Armor​​​​​​​ 3D Printing Figurine at Gambody YouTube channel.

Also, you may like other WoW 3D Printing Figurines.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 3.5.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for CuraSimplify3D and Slic3r softwares.

Cura printing recommendations:

Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

To avoid printing problems, we recommend the following settings:

Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm 
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill Density: 20%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s 

Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
    Support Speed: 45 mm/s 
     Support Infill Speed: 45 mm/s
Travel Speed: 45 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 45 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.6562 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100% 
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2 
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 2.2 mm
Support Z Distance: 0.13 mm
    Support Top Distance: 0.13 mm
    Support Bottom Distance: 0.13 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 15 
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Extruder 1 Temperature: 210
Heated Bed: 60

Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
  Detect thin walls: Check
  Detect bridging perimeters: Check
  Seam position: Random
  Fill desity: 20%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
  Infill/Perimeters overlap: 20%
  Bridge flow ratio: 0.95
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm


comments powered by Disqus

Similar items

Browse more newly listed 3D printings