Make pre-order

(4)
small
cm: 24.18 w x 15.88 d x 26.46 h
in: 9.52 w x 6.252 d x 10.417 h
2
BUY FOR  $14.99

Source Files

|

Description

|

Printing Details

This 3D model consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

File Name File Size Time / Filament
1_WolverineUpper (repaire d) (Shell 3).stl
28.54 MiB 22 h 26 min
15 m
Download
2_Gambody_Connector_2.5cm (repaired).stl
0.04 MiB 7 min
<1 m
Download
3_Gambody_Connector_2cm_L eft_hand (repaired).stl
0.04 MiB 6 min
<1 m
Download
4_WolverineLower_Body (re paired).stl
26.94 MiB 21 h 7 min
15 m
Download
5_WolverineHead (repaired ).stl
87.88 MiB n.a.
n.a.
Download
6_Wolverineshoulder_R (re paired).stl
2.78 MiB 2 h 7 min
2 m
Download
7_Wolverineshoulder_L (re paired).stl
2.92 MiB 1 h 58 min
2 m
Download
8_WolverineArm_R (repaire d).stl
37.46 MiB 3 h 11 min
2 m
Download
9_Wolverinearm_L (repaire d).stl
51.39 MiB 3 h 46 min
2 m
Download
10_Wolverineleg_R (repair ed).stl
20.56 MiB 6 h 7 min
4 m
Download
11_WolverineLeg_L (repair ed).stl
25.51 MiB 14 h 40 min
9 m
Download
Wolverine_solid 20cm (rep aired).stl
52.06 MiB 52 h 44 min
38 m
Download

The Wolverine is one of the most popular and well-known characters from the widely acclaimed “X-Men” comics series. The last movie about him, “Logan”, impressed lots of viewers all over the world. But he never appeared in his canonic yellow suit on the big screen. 

So especially for those who prefer canon Wolverine look, there’s now a Wolverine 3D model available for 3D printing. He stands with one of his legs on the rock. This pose expresses power and anger of the character. His claws are also shown up and it makes him look like he is ready to attack at this very moment. 

The Wolverine (also known as Logan or Weapon X) first appeared in Marvel comics in 1974. As a character, he gained his popularity together with X-men team. His superpowers, which are animal-keen senses, regenerative abilities, and enhanced physical capabilities are the result of the experiment. He looks and acts like a typical antihero of those times, ready to use his claws and his deadly power. He doesn’t hesitate to take a life away. Though there is something good in him, which makes him so attractive and charismatic in a compliance with a tragic fate. 

The assembling version of the 3D printing model consists of eleven parts in order for users to put them together easily. Being split into pieces helps to save printing material that usually goes into supports. But there’s also a static version in case you want to avoid assembling. 

After being 3D printed, the 3D model will stand  241.8 mm wide, 264.6 mm tall, and 158.8 mm deep.

Buy SM - Wolverine 3D model right now! Just click the green Buy button in the top-right corner of the model's page. You can pay with PayPal or your credit card.

 

_____________________________________
FAQ: 
Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?

This model was tested in Cura 2.3.1. To avoid printing problems, we recommend the following settings:

Quality

Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
Wall Line Width: 0.4 mm
Outer Wall Line Width: 0.4 mm
Inner Wall(s) Line Width: 0.4 mm
Top/Bottom Line Width: 0.4 mm
Infill Line Width: 0.4 mm
Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm

Shell

Wall Thickness: 0.8 mm
Wall Line Count: 2
Top/Bottom Thickness: 0.8 mm
Top Thickness: 0.8 mm
Top Layers: 8
Bottom Thickness: 0.8 mm
Bottom Layers: 8
Top/Bottom Pattern: Lines
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
Compensate Outer Wall Overlaps: Check
Compensate Inner Wall Overlaps: Check
Horizontal Expansion: 0 mm
Z Seam Alignment: Shortest

Infill

Infill Density: 25%
Infill Line Distance: 3.2 mm
Infill Pattern: Grid
Infill Overlap Percentage: 10%
Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 0
Infill Before Walls: Check

Material

Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Standby Temperature: 175°C
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
Nozzle Switch Retract Speed: 20 mm/s
Nozzle Switch Prime Speed: 20 mm/s

Speed

Print Speed: 60 mm/s
Infill Speed: 80 mm/s
Wall Speed: 30 mm/s
Outer Wall Speed: 30 mm/s
Inner Wall Speed: 60 mm/s
Top/Bottom Speed 15 mm/s
Support Speed: 60 mm/s
Support Infill Speed: 60 mm/s
Travel Speed: 120 mm/s
Initial Layer Speed: 15 mm/s
Initial Layer Print Speed: 15 mm/s
Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed 15 mm/s
Maximum Z Speed: 0 mm/s

Travel

Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm

Cooling

Enable Print Cooling: Check
Fan Speed: 100%
Regular Fan Speed: 100%
Maximum Fan Speed: 100%
Regular/Maximum Fan Speed Threshold: 10 s
Regular Fan Speed at Height: 0.3 mm
Regular Fan Speed at Layer: 2
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Support

Enable Support: Check
Support Placement: Everywhere
Support Overhang Angle: 50°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 30 %
Support Line Distance: 1.3333 mm
Support Z Distance: 0.1 mm
Support Top Distance: 0.1 mm
Support Bottom Distance: 0.1 mm
Support X/Y Distance: 0.7 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.2 mm
Support Stair Step Height: 0.3 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65°

Build Plate Adhesion

Build Plate Adhesion Type: Brim
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
Brim Line Count: 20
Brim Only on Outside: Check

Mesh Fixes

Union Overlapping Volumes: Check

Special Modes

Print Sequence: All at Once
Surface Mode: Normal

Experimental

Extra Skin Wall Count: 0

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Comments

comments powered by Disqus

Similar items