Premium Stock

Mach Patrol 3D Printing Model | Assembly + Action

cm: 9.3 w x 20.7 d x 5.7 h
in: 3.661 w x 8.15 d x 2.244 h

Source Files




Printing Details

This 3D Model consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

Mach Patrol 3D Printing Model comes in 1 version for FFF/FDM 3D printers. STL files of the version are available for download after the purchase.

Detailed information about this 3D printing model is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
1_frame (repaired).stl
1.07 MiB 25 h 21 min 16 m 93 x 204 x 42 Download
2_consolle (repaired).stl
0.18 MiB 54 min <1 m 49 x 19 x 18 Download
3_seat (repaired).stl
2.03 MiB 59 min <1 m 31 x 23 x 36 Download
4_joint door (repaired).s tl
0.30 MiB 10 min <1 m 19 x 20 x 3 Download
5_door_glass (repaired).s tl
6.54 MiB 2 h 44 min 2 m 67 x 26 x 68 Download
6_flap1 (repaired).stl
0.12 MiB 1 h 23 min 1 m 44 x 88 x 20 Download
7_flap2 (repaired).stl
0.09 MiB 9 min <1 m 28 x 12 x 4 Download
8_flap3 (repaired).stl
0.09 MiB 9 min <1 m 28 x 12 x 4 Download
9_propeller (repaired).st l
1.30 MiB 3 h 54 min 2 m 40 x 30 x 51 Download
10_pin (repaired).stl
0.02 MiB 35 min <1 m 5 x 5 x 85 Download
11_missile x2 (repaired). stl
0.07 MiB 37 min <1 m 12 x 11 x 46 Download
12_frame_front_R (repaire d).stl
0.93 MiB 5 h 50 min 3 m 25 x 102 x 29 Download
13_frame_front_L (repaire d).stl
0.93 MiB 5 h 49 min 3 m 25 x 102 x 29 Download
14_joint frame_R (repaire d).stl
0.07 MiB 7 min <1 m 12 x 5 x 7 Download
15_joint frame_L (repaire d).stl
0.07 MiB 7 min <1 m 12 x 5 x 7 Download
16_wing_R1 (repaired).stl
0.19 MiB 1 h 9 min 1 m 5 x 55 x 34 Download
17_wing_R2 (repaired).stl
0.06 MiB 30 min <1 m 7 x 25 x 30 Download
18_wing_L1 (repaired).stl
0.19 MiB 1 h 10 min 1 m 5 x 55 x 34 Download
19_wing_L2 (repaired).stl
0.06 MiB 30 min <1 m 7 x 25 x 30 Download
20_front tip (repaired).s tl
0.16 MiB 2 h 42 min 2 m 33 x 14 x 80 Download
21_fork1 (repaired).stl
0.02 MiB 7 min <1 m 28 x 17 x 2 Download
22_fork2 (repaired).stl
0.02 MiB 7 min <1 m 28 x 17 x 2 Download
23_grid (repaired).stl
0.25 MiB 25 min <1 m 33 x 7 x 20 Download
24_landing gear1 (repaire d).stl
0.11 MiB 7 min <1 m 18 x 8 x 6 Download
25_landing gear2 (repaire d).stl
0.11 MiB 8 min <1 m 4 x 7 x 13 Download
26_wheel_1_x4 (repaired). stl
3.45 MiB 52 min <1 m 25 x 25 x 15 Download
27_wheel_2_x4 (repaired). stl
0.23 MiB 8 min <1 m 12 x 12 x 7 Download
28_tire_x4 (repaired).stl
1.07 MiB 42 min <1 m 30 x 30 x 13 Download
Keychain (repaired).stl
0.35 MiB 23 min <1 m 30 x 30 x 2 Download
Tag (repaired).stl
1.70 MiB 1 h 16 min 1 m 150 x 18 x 5 Download


Mach Patrol is the police cruiser-like car that belongs to Banjō Haran, the protagonist of the Invincible Steel Man Daitarn 3 anime series. The car’s main feature is its ability to transform into a plane mode known as Mach Attacker. And the author of the model spent 114 hours to design the Mach Patrol for 3D printing the would possess the same characteristics. And now any fan of the legendary vehicle has an opportunity to obtain a transformable model having printed it on a 3D printer. Mach Patrol for 3D printing also features all the assembly parts typically associated with the vehicle from the anime series. A pair of bladed wings, also known as the Mach Blades, balloon-like mines called the Mach Balloons and spikes called the Mach Picks are there to depict the car with as much attention to detail as possible. Don't hesitate, hurry up to start the legendary project!


Mach Patrol model for 3D printing is a highly articulated assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 32 hours in total. In order to ensure the robot’s transformation, it was divided into many assembly parts and all of them were designed to presuppose the introduction of a certain mechanism to give you an opportunity to switch between the car’s modes. Mach Patrol’s driver seat, steering wheel, Mach Picks etc. are provided as a separate files for you to receive the cleanest printed result. All the assembly parts are provided in STL files in recommended positions that were worked out so to ensure the smoothness of the details’ surfaces after printing and so that the 3D printing beginners won't face difficulties when placing the parts on a build plate. In order to assemble the model, you will need short pieces of 1.75 PLA to make pins. Make sure to watch "Assembly video" in the photo preview section before assembly and apply the glue where you feel appropriate. 

The model is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from Mach Patrol's actual length that is 5800 mm. The 3D printing model's chosen scale is 1/28 for the FFF/FDM version.


FFF/FDM 1.0 version features:
- Contains 28 parts;
- A printed model is 57 mm tall, 93 mm wide, 207 mm deep;
- Can transform into Mach Attacker mode;
- Each robot’s part is articulated which allows the model's transformation;
- The cockpit can be opened to access the passenger compartment;
- The model can be assembled with 1.75 PLA pins;
- All parts are divided in such a way that you will print them with the smallest number of support structures.


- STL files of Mach Patrol Model for 3D printing which consist of 28 parts;
- High-poly detailed model of Mach Patrol;
- Detailed settings that we provide as a recommendation for Cura , Simplify3D and Slic3r for the best print;
- Full technical support from the Gambody Support Team.

You can get the model of Mach Patrol for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Mach Patrol​ 3D Printing Model at Gambody YouTube channel.

Also, you may like another Robot 3D Printing Models as well as other Anime 3D Printing Figurines.


Where can I print a model if I have no printer?
How to get started with 3D printing?
How to set up my 3D printer?
How to choose right 3D model print bed positioning? 
How to paint printed figurine?


This model was tested in Cura 3.4.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for CuraSimplify3D and Slic3r softwares.

Cura printing recommendations:

Recommendations: Use ABS or PLA Plus filament to print more durable and friction resistant details.

To avoid printing problems, we recommend the following settings:

Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
 Wall Line Width: 0.4 mm
   Outer Wall Line Width: 0.4 mm
   Inner Wall(s) Line Width: 0.4 mm
 Top/Bottom Line Width: 0.4 mm
 Infill Line Width: 0.4 mm
 Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm
 Initial Layer Line Width: 100%

Wall Thickness: 0.8 mm
    Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
   Top Thickness: 0.8 mm
      Top Layers: 8
    Bottom Thickness: 0.8 mm
      Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
    Compensate Outer Wall Overlaps: Check
    Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1

Infill Density: 80%
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
    Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
    Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 1
Gradual Infill Steps Height: 1.5 mm
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
    Top Skin Removal Width: 0.8 mm
    Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
    Top Skin Expand Distance: 0.8
    Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
    Minimum Skin Width for Expansion: 0.0

Initial Layer Flow: 100%
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
    Nozzle Switch Retract Speed: 20 mm/s
    Nozzle Switch Prime Speed: 20 mm/s

Print Speed: 45 mm/s
    Infill Speed: 45 mm/s
    Wall Speed: 22.5 mm/s
      Outer Wall Speed: 22.5 mm/s
      Inner Wall Speed: 45 mm/s
    Top/Bottom Speed: 15 mm/s
Travel Speed: 45 mm/s
Initial Layer Speed: 22.5 mm/s
  Initial Layer Print Speed: 22.5 mm/s
  Initial Layer Travel Speed: 30 mm/s
Skirt/Brim Speed: 30 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2

Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm

Enable Print Cooling: Check
Fan Speed: 100%
    Regular Fan Speed: 100%
    Maximum Fan Speed: 100%
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
    Regular Fan Speed at Layer: 2
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s

Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 50°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
    Support Line Distance: 3 mm
Support Z Distance: 0.1 mm
    Support Top Distance: 0.1 mm
    Support Bottom Distance: 0.1 mm
Support X/Y Distance: 1 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.25 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Gradual Support Infill Steps: 0
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65°

Build Plate Adhesion 
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
    Brim Line Count: 18
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 80%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Extruder 1 Temperature: 210
Heated Bed: 60

Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

Layer height
  Layer height: 0.1 mm
  First layer height: 90%
Vertical shells
  Perimeters: 2
Horizontal shells
  Soid layers: 
              Top: 8
              Bottom: 5
  Detect thin walls: Check
  Detect bridging perimeters: Check
  Seam position: Random
  Fill density: 80%
  Fill pattern: Honeycomb
  Top/bottom fill pattern: Rectilinear
Reducing printing time
  Combine infill every: 1 layers
  Solid infill every: 0 layers
  Fill angle: 25 deg
  Solid infill threshold area: 0mm
  Loops: 2
  Distance from object: 6 mm
  Skirt height: 1 layers
  Minimum extrusion length: 4 mm
  Brim width: 10 mm
Support material
  Generate support material: Check
  Overhang threshold: 45 deg
  Enforce support for the first: 3 layers
  Raft layers: 0 layers
Options for support material and raft
  Contact Z distance: 0.1 mm
  Pattern: Rectilinear
  Patter spacing: 2 mm
  Pattern angle: 0 deg
  Interface layers: 2 layers
  Interface pattern spacing: 0.2 mm
Speed for print moves
  Perimeters: 60 mm/s
  Small perimeters: 20 mm/s
  External perimeters: 20 mm/s
  Infill: 60 mm/s
  Solid infill: 60 mm/s
  Top solid infill: 30 mm/s
  Support material: 50 mm/s
  Support material interface: 100%
  Bridges: 30 mm/s
  Gap fill: 50 mm/s
Speed for non-print moves
  Travel: 60 mm/s
  First layer speed: 30 mm/s
Acceleration control
  Perimeters: 800 mm/s
  Infill: 1500 mm/s
  Bridge: 1000 mm/s
  First layer: 1000 mm/s
  Default: 1000 mm/s
  Max print speed: 100 mm/s
  Max volumetrix speed: 0 mm/s
Extrusion width
  Default extrusion width: 0.42 mm
  First layer: 0.42 mm
  Perimeters: 0.42 mm
  External perimeters: 0.42 mm
  Infill: 0.42 mm
  Solid infill: 0.42 mm
  Top solid infill: 0.42 mm
  Support material: 0.42 mm
  Infill/Perimeters overlap: 20%
  Bridge flow ratio: 0.95
  XY Size Compensation: 0 mm
  Threds: 8
  Resolution: 0 mm


    comments powered by Disqus

    Similar items

    Browse more newly listed 3D printings