What game heroes would you like to see at gambody?
MWO King Crab Action Figure for 3D Printing
This 3D model consists of files in StereoLithography (.Stl) format that have been optimized for 3D printing.
Before printing the files, we strongly recommend reading the PRINTING DETAILS section.
Version 2 and Version 3 are the new files for MWO King Crab 3D Model optimized for 3D printing, the preview pictures of which you see above.
It is recommended:
- Version 1 STL files on FDM/FFF 3D printers - old version with old joints;
- Version 2 STL files on FDM/FFF 3D printers - new version with new scale and new joints;
- Version 3 STL files on DLP/SLA/SLS 3D printers - new version with new scale and new joints.
|File Name||File Size||Time / Filament|
KING CRAB_1 (repaired).st l
52 h 35 min
KING CRAB_2 (repaired).st l
12 h 40 min
KING CRAB_FL (repaired).s tl
KING CRAB_L1 (repaired).s tl
4 h 58 min
KING CRAB_L10 (repaired). stl
KING CRAB_L2 (repaired).s tl
20 h 11 min
KING CRAB_L3 (repaired).s tl
6 h 16 min
KING CRAB_L4 (repaired).s tl
KING CRAB_L5 (repaired).s tl
4 h 2 min
KING CRAB_L6 (repaired).s tl
2 h 11 min
KING CRAB_L7 (repaired).s tl
4 h 47 min
KING CRAB_L8 (repaired).s tl
7 h 32 min
KING CRAB_L9 (repaired).s tl
KING CRAB_LRM20 (repaired ).stl
1 h 18 min
KING CRAB_LS (repaired).s tl
KING CRAB_L_AC5 (repaired ).stl
KING CRAB_R1 (repaired).s tl
4 h 58 min
KING CRAB_R10 (repaired). stl
KING CRAB_R2 (repaired).s tl
20 h 12 min
KING CRAB_R3 (repaired).s tl
6 h 13 min
KING CRAB_R4 (repaired).s tl
KING CRAB_R5 (repaired).s tl
4 h 1 min
KING CRAB_R6 (repaired).s tl
2 h 11 min
KING CRAB_R7 (repaired).s tl
4 h 43 min
KING CRAB_R8 (repaired).s tl
7 h 31 min
KING CRAB_R9 (repaired).s tl
KING CRAB_R_AC5 (repaired ).stl
This should take overall.
King Crab 3D model is inspired by the video game Mech.
This BattleMech was designed at the request of General Aleksandr Kerensky. Featuring crab-like arms, the Mech is capable of stripping the armor off of any Mech. King Crab is considered one of the best close-range MechWarriors. His only disadvantage is that it cannot hold too much ammo and it easily becomes vulnerable to the enemy attacks when left without firepower.
King Crab Battlemech can be destroyed by heavy assault Mechs, but the latter will suffer damage in the process.
The 3D printing model features the Autocannon on each of its arms. The claw-shaped actuators make reference to the real crab’s pinchers.
King Crab 3D model is created in Autodesk Maya. The model features a lot of impressive details and an intricate surface shell. The files are converted to STL format and can be easily handled in any slicing program. The model is made solid to facilitate its printing on any type of 3D printer.
All the files have been checked and corrected in Netfabb.
The model consists of 27 separate parts. After being 3D printed the model will stand 180 mm wide, 250 mm tall, and 168 mm deep. It has hinged joints which increase its workability.
Buy King Crab 3D model STL files by clicking the green Buy button. Continue to checkout. Provide your credit card or PayPal details and download the files in a .zip folder.
Or, 3D print the models with 3DHubs or Treatstock directly from our website. Select the files and click the Print with 3DHubs or Print with Treastock button. You will be redirected to their website, where you can choose the 3D printing service provider, the printing material, the size of the model, and get the model shipped to your home address.
On 28.03.2018 new version of joints have been added.
Now, the MWO King Crab 3D Model is available in two scale: 1/60 for Version 2 (FDM/FFF) and 1/100 for Version 3 (DLP/SLA/SLS).
There are 28 parts in Version 2 (FDM/FFF) and 14 parts for Version 3 (DLP/SLA/SLS).
Was added parts pf Locks and Connectors for better fixing.
- One part of Lock(20_Ge_lock_7S_x4) you need to print 4 times.
- One part of Connector(7_Ge_Connector_A_A_x2) you need to print twice.
- One part of Claw(11_B_Claw_x9) you nned to print 9 times.
- One part of Joint(24_Axis_1_B_Joint_x2) you need to print twice.
- One part of Joint(10_Axis_2_B_Joint_x7) you need to print 7 times.
Version 2 (FDM/FFF):
- Is 1:60 scale and after being printed will stand 250 mm tall, 211 mm wide, 180 mm deep;
- Made with new joints;
- All movable elements of the Mech were saved.
Version 3 (DLP/SLA/SLS):
- Is 1:100 scale and will stand 150 mm tall, 106 mm wide, 90 mm deep;
- Made with new joints;
- All movable elements of the Mech were saved;
- Has as few details as possible to keep printing costs down.
With new joints from Version 2 and Version 3 you will get next advantages:
1. Increases frictional force;
2. Possible to up scale or down scale the whole model;
3. Printable from any type of material;
4. Higher strength;
5. Material shrinkage does not affect at strength and friction.
STL files with new scale and new joints are already available for download in “Source files” tab for:
- Version 2 - STL files on FDM/FFF 3D printers;
- Version 3 - STL files on DLP/SLA/SLS 3D printers.
Also, you can get perfect Guns Pack for this mech.
This model was tested in Cura 3.2.1 and printed on an Ultimaker 2 in PLA material.
- You can print new joints from Version 2 and Version 3 with 20-30% infill.
- With the new joints from Version 2 and Version 3 you can up scale or down scale the whole model.
- Connectors should be printed at 100% infill.
- For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.
To avoid printing problems, we recommend the following settings:
Layer Height: 0.1 mm
Initial Layer Height: 0.3 mm
Line Width: 0.4 mm
Wall Line Width: 0.4 mm
Outer Wall Line Width: 0.4 mm
Inner Wall(s) Line Width: 0.4 mm
Top/Bottom Line Width: 0.4 mm
Infill Line Width: 0.4 mm
Skirt/Brim Line Width: 0.4 mm
Initial Layer Line Width: 100%
Wall Thickness: 0.8 mm
Wall Line Count: 2
Outer Wall Wipe Distance: 0.2 mm
Top Surface Skin Layers: 0
Top/Bottom Thickness: 0.8 mm
Top Thickness: 0.8 mm
Top Layers: 8
Bottom Thickness: 0.8 mm
Bottom Layers: 8
Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Compensate Wall Overlaps: Check
Compensate Outer Wall Overlaps: Check
Compensate Inner Wall Overlaps: Check
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Z Seam Alignment: Sharpest Corner
Seam Corner Preference: Hide Seam
Ignore Small Z Gaps: Check
Extra Skin Wall Count: 1
Infill Density: 20% (connectors should be printed at 100% infill)
Infill Line Distance: 4.0 mm
Infill Pattern: Grid
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Overlap Percentage: 10%
Infill Overlap: 0.04 mm
Skin Overlap Percentage: 5%
Skin Overlap: 0.02 mm
Infill Wipe Distance: 0.1 mm
Infill Layer Thickness: 0.1 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2
Skin Removal Width: 0.8 mm
Top Skin Removal Width: 0.8 mm
Bottom Skin Removal Width: 0.8 mm
Skin Expand Distance: 0.8
Top Skin Expand Distance: 0.8
Bottom Skin Expand Distance: 0.8
Maximum Skin Angle for Expansion: 90˚
Minimum Skin Width for Expansion: 0.0
Enable Retraction: Check
Retraction Extra Prime Amount: 0 mm3
Retraction Minimum Travel: 0.8 mm
Maximum Retraction Count: 90
Minimum Extrusion Distance Window: 6.5 mm
Nozzle Switch Retraction Distance: 16 mm
Nozzle Switch Retraction Speed: 20 mm/s
Nozzle Switch Retract Speed: 20 mm/s
Nozzle Switch Prime Speed: 20 mm/s
Print Speed: 45 mm/s
Infill Speed: 50 mm/s
Wall Speed: 22.5 mm/s
Outer Wall Speed: 22.5 mm/s
Inner Wall Speed: 45 mm/s
Top/Bottom Speed: 15 mm/s
Travel Speed: 120 mm/s
Initial Layer Speed: 30 mm/s
Initial Layer Print Speed: 30 mm/s
Initial Layer Travel Speed: 60 mm/s
Skirt/Brim Speed: 30 mm/s
Maximum Z Speed: 0 mm/s
Number of Slower Layers: 2
Combing Mode: All
Avoid Printed Parts when Traveling: Check
Travel Avoid Distance: 0.625 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm
Enable Print Cooling: Check
Fan Speed: 100%
Regular Fan Speed: 100%
Maximum Fan Speed: 100%
Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.3 mm
Regular Fan Speed at Layer: 2
Minimum Layer Time: 5 s
Minimum Speed: 10 mm/s
Generate Support: Check
Support Placement: Everywhere
Support Overhang Angle: 60°
Support Pattern: Zig Zag
Connect Support ZigZags: Check
Support Density: 15 %
Support Line Distance: 1.3333 mm
Support Z Distance: 0.3 mm
Support Top Distance: 0.3 mm
Support Bottom Distance: 0.3 mm
Support X/Y Distance: 0.7 mm
Support Distance Priority: Z overrides X/Y
Minimum Support X/Y Distance: 0.2 mm
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.1 mm
Use Towers: Check
Tower Diameter: 3.0 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65°
Build Plate Adhesion
Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
Brim Line Count: 18
Brim Only on Outside: Check
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm
Print Sequence: All at Once
Surface Mode: Normal
Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%
Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.