Ecto-1 3D Printing Model | Assembly + Active

(11)
cm: 17.9 w x 47.6 d x 21.7 h
in: 7.047 w x 18.74 d x 8.543 h

Source Files

|

Description

|

Printing Details

This 3D Model of the Ecto-1 from Ghostbusters consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

WHAT WILL YOU GET AFTER PURCHASE?

  • 2 versions of Ectomobile STL files for FFF/FDM and DLP/SLA - files for all versions are available for download after the purchase
  • STL files of high-poly Ghostbusters Car 3D Model for 3D printing consist of 294 parts
  • Sizes:
  • FFF/FDM: 217 mm tall, 179 mm wide, 476 mm deep
  • DLP/SLA: 108 mm tall, 90 mm wide, 238 mm deep
  • Assembly Manual for FFF/FDM 1.0 and DLP/SLA 1.0 versions in PDF format
  • Detailed settings that we provide as a recommendation for Cura, Simplify3D, Slic3r and PrusaSlicer for the best print- Full technical support from the Gambody Support Team

Detailed information about this 3D printing model is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
_01_framePart_a_FDM (repa ired).stl
6.28 MiB 9 h 55 min 7 m 107 x 198 x 25 Download
_02_framePart_b_FDM (repa ired).stl
1.19 MiB 2 h 37 min 1 m 59 x 11 x 74 Download
_03_framePart_c_FDM (repa ired).stl
4.38 MiB 14 h 16 min 9 m 88 x 19 x 182 Download
_04_framePart_d_X2_FDM (r epaired).stl
0.18 MiB 9 min <1 m 9 x 17 x 7 Download
_05_framePin_X8_FDM (repa ired).stl
0.32 MiB 3 min <1 m 5 x 15 x 3 Download
_06_spring_X2_FDM (repair ed).stl
2.41 MiB 12 min <1 m 11 x 11 x 10 Download
_07_steeringBeam_FDM (rep aired).stl
0.51 MiB 20 min <1 m 97 x 13 x 6 Download
_08_wheelAxis_FrontL_FDM (repaired).stl
0.87 MiB 19 min <1 m 22 x 21 x 17 Download
_09_wheelAxis_FrontR_FDM (repaired).stl
3.47 MiB 19 min <1 m 22 x 21 x 17 Download
_10_wheelAxisPart_a_Front L_FDM (repaired).stl
0.73 MiB 8 min <1 m 12 x 4 x 7 Download
_11_wheelAxisPart_a_Front R_FDM (repaired).stl
0.73 MiB 8 min <1 m 12 x 4 x 7 Download
_12_wheelAxisPart_b_Front L_FDM (repaired).stl
0.73 MiB 8 min <1 m 12 x 4 x 7 Download
_13_wheelAxisPart_b_Front R_FDM (repaired).stl
0.73 MiB 8 min <1 m 12 x 4 x 7 Download
_14_wheelAxisPart_c_Front L_FDM (repaired).stl
2.14 MiB 42 min <1 m 33 x 9 x 28 Download
_15_wheelAxisPart_c_Front R_FDM (repaired).stl
1.24 MiB 25 min <1 m 23 x 11 x 19 Download
_16_wheelAxisPart_d_Front L_FDM (repaired).stl
1.24 MiB 25 min <1 m 23 x 11 x 19 Download
_17_wheelAxisPart_d_Front R_FDM (repaired).stl
2.14 MiB 44 min <1 m 33 x 9 x 28 Download
_18_wheelAxisPart_e_Front L_FDM (repaired).stl
0.39 MiB 5 min <1 m 7 x 22 x 5 Download
_19_wheelAxisPart_e_Front R_FDM (repaired).stl
0.39 MiB 5 min <1 m 7 x 22 x 5 Download
_20_wheelAxisPart_f_Front L_FDM (repaired).stl
0.21 MiB 7 min <1 m 12 x 14 x 4 Download
_21_wheelAxisPart_f_Front R_FDM (repaired).stl
0.21 MiB 7 min <1 m 12 x 14 x 4 Download
_22_wheelAxisPart_g_Front L_FDM (repaired).stl
0.53 MiB 9 min <1 m 8 x 9 x 9 Download
_23_wheelAxisPart_g_Front R_FDM (repaired).stl
0.53 MiB 9 min <1 m 8 x 9 x 9 Download
_24_wheelAxisPartPin_X4_F DM (repaired).stl
0.28 MiB 3 min <1 m 10 x 5 x 3 Download
_25_cardan_Rr_FDM (repair ed).stl
1.49 MiB 32 min <1 m 8 x 8 x 64 Download
_26_differentialPart_a_FD M (repaired).stl
4.27 MiB 1 h 13 min 1 m 133 x 18 x 14 Download
_27_differentialPart_b_FD M (repaired).stl
2.49 MiB 25 min <1 m 17 x 17 x 22 Download
_28_wheelBrakeDisk_X4_FDM (repaired).stl
0.92 MiB 15 min <1 m 23 x 23 x 3 Download
_29_wheelDisk_X4_FDM (rep aired).stl
20.42 MiB 1 h 8 min 1 m 31 x 31 x 14 Download
_30_wheelTire_X4_FDM (rep aired).stl
62.71 MiB 2 h 50 min 2 m 54 x 54 x 16 Download
_31_spring_RearL_FDM (rep aired).stl
1.68 MiB 33 min <1 m 116 x 19 x 5 Download
_32_spring_RearR_FDM (rep aired).stl
1.68 MiB 33 min <1 m 116 x 19 x 5 Download
_33_enginePart_a_FDM (rep aired).stl
14.10 MiB 57 min 1 m 28 x 44 x 14 Download
_37_enginePart_e_FDM (rep aired).stl
7.58 MiB 51 min <1 m 31 x 32 x 7 Download
_39_enginePart_g_FDM (rep aired).stl
0.74 MiB 19 min <1 m 25 x 18 x 16 Download
_40_enginePart_h_FDM (rep aired).stl
4.74 MiB 17 min <1 m 25 x 20 x 11 Download
_41_enginePart_i_FDM (rep aired).stl
0.33 MiB 5 min <1 m 8 x 8 x 9 Download
_42_enginePart_j_FDM (rep aired).stl
0.32 MiB 8 min <1 m 7 x 7 x 10 Download
_43_enginePart_k_FDM (rep aired).stl
0.32 MiB 11 min <1 m 7 x 7 x 13 Download
_44_airFilter_FDM (repair ed).stl
1.58 MiB 44 min <1 m 33 x 37 x 7 Download
_45_engineBelt_a_FDM (rep aired).stl
0.16 MiB 4 min <1 m 40 x 25 x 2 Download
_46_engineBelt_ab_FDM (re paired).stl
0.16 MiB 4 min <1 m 41 x 27 x 2 Download
_47_engineBolt_V1_X2_FDM (repaired).stl
0.23 MiB 1 min <1 m 2 x 2 x 7 Download
_48_engineCardan_FDM (rep aired).stl
0.54 MiB 19 min <1 m 58 x 18 x 8 Download
_49_engineCooler_FDM (rep aired).stl
10.41 MiB 7 min <1 m 23 x 22 x 3 Download
_50_engineEaxhaust_L_FDM (repaired).stl
52.49 MiB 17 min <1 m 26 x 35 x 9 Download
_51_engineEaxhaust_R_FDM (repaired).stl
52.55 MiB 17 min <1 m 26 x 35 x 10 Download
_52_enginePart_l_FDM (rep aired).stl
0.31 MiB 12 min <1 m 7 x 7 x 16 Download
_53_engineHolder_X2_FDM ( repaired).stl
0.01 MiB 5 min <1 m 11 x 14 x 4 Download
_54_enginePin_a_FDM (repa ired).stl
0.01 MiB 4 min <1 m 9 x 14 x 2 Download
_55_enginePin_b_FDM (repa ired).stl
0.01 MiB 5 min <1 m 11 x 11 x 4 Download
_56_trnasmissionPart_a_FD M (repaired).stl
24.19 MiB 1 h 37 min 1 m 28 x 28 x 42 Download
_57_trnasmissionPart_b_FD M (repaired).stl
3.02 MiB 16 min <1 m 24 x 17 x 7 Download
_58_transmissionPin_V1_FD M (repaired).stl
0.01 MiB 2 min <1 m 3 x 5 x 3 Download
_59_transmissionPin_V2_X2 _FDM (repaired).stl
0.00 MiB 3 min <1 m 3 x 12 x 3 Download
_60_exhaustPart_a_L_FDM ( repaired).stl
0.81 MiB 51 min <1 m 31 x 47 x 9 Download
_61_exhaustPart_b_R_FDM ( repaired).stl
0.81 MiB 48 min <1 m 21 x 9 x 43 Download
_62_exhaustPart_c_L_FDM ( repaired).stl
12.84 MiB 57 min 1 m 54 x 25 x 49 Download
_63_exhaustPart_d_R_FDM ( repaired).stl
2.13 MiB 1 h 6 min <1 m 43 x 22 x 64 Download
_64_exhaustPart_e_L_FDM ( repaired).stl
2.06 MiB 59 min <1 m 9 x 9 x 128 Download
_65_exhaustPart_f_R_FDM ( repaired).stl
2.06 MiB 59 min <1 m 9 x 9 x 128 Download
_66_exhaustPart_g_L_FDM ( repaired).stl
2.35 MiB 26 min <1 m 14 x 19 x 60 Download
_67_exhaustPart_h_L_FDM ( repaired).stl
0.71 MiB 50 min <1 m 23 x 10 x 101 Download
_68_exhaustPart_h_R_FDM ( repaired).stl
2.35 MiB 26 min <1 m 14 x 19 x 60 Download
_69_exhaustPartHolder_X2_ FDM (repaired).stl
0.16 MiB 8 min <1 m 9 x 14 x 7 Download
_70_engineBolt_V2_X2_01_F DM (repaired).stl
0.19 MiB 1 min <1 m 2 x 2 x 8 Download
_71_exhaustTubePin_X2_FDM (repaired).stl
0.18 MiB 2 min <1 m 2 x 2 x 9 Download
_72_radiator_FDM (repaire d).stl
7.01 MiB 3 h 24 min 2 m 65 x 7 x 48 Download
_73_exhaustPart_i_R_FDM ( repaired).stl
0.71 MiB 50 min <1 m 23 x 9 x 101 Download
_74_bodyPart_a_F_FDM (rep aired).stl
43.25 MiB 9 h 51 min 6 m 169 x 22 x 39 Download
_75_bodyPart_b_F_FDM (rep aired).stl
79.83 MiB 35 h 30 min 24 m 164 x 58 x 118 Download
_77_bodyPart_d_Mid_FDM (r epaired).stl
28.74 MiB 46 h 43 min 29 m 160 x 111 x 86 Download
_78_bodyPart_e_RearR_FDM (repaired).stl
63.57 MiB 39 h 10 min 23 m 84 x 111 x 159 Download
_79_bodyPart_f_RearL_FDM (repaired).stl
59.25 MiB 40 h 10 min 23 m 81 x 111 x 159 Download
_80_door_V2_FrontL_FDM1 ( repaired).stl
39.02 MiB 8 h 31 min 5 m 30 x 93 x 83 Download
_81_door_V2_FrontR_FDM (r epaired).stl
39.24 MiB 8 h 25 min 5 m 30 x 93 x 83 Download
_82_door_V1_FrontL_FDM (r epaired).stl
33.13 MiB 7 h 58 min 4 m 27 x 93 x 83 Download
_83_door_V1_FrontR_FDM (r epaired).stl
33.35 MiB 7 h 41 min 4 m 27 x 93 x 83 Download
_84_door_RearR_FDM (repai red).stl
29.89 MiB 9 h 23 min 5 m 28 x 94 x 85 Download
_85_door_RearL_FDM (repai red).stl
29.89 MiB 9 h 24 min 5 m 28 x 94 x 85 Download
_86_doorFrontGlass_a_L_FD M (repaired).stl
0.21 MiB 42 min <1 m 53 x 39 x 3 Download
_87_doorFrontGlass_a_R_FD M (repaired).stl
0.21 MiB 42 min <1 m 53 x 39 x 3 Download
_88_doorFrontGlass_b_L_FD M (repaired).stl
0.17 MiB 8 min <1 m 13 x 28 x 3 Download
_89_doorFrontGlass_b_R_FD M (repaired).stl
0.17 MiB 8 min <1 m 13 x 28 x 3 Download
_90_doorFrontPin_a_X2_FDM (repaired).stl
0.11 MiB 8 min <1 m 18 x 8 x 5 Download
_91_doorFrontPin_b_X2_FDM (repaired).stl
0.17 MiB 28 min <1 m 26 x 16 x 14 Download
_92_doorRear_V1_FDM (repa ired).stl
14.70 MiB 5 h 5 min 3 m 45 x 75 x 86 Download
_93_doorRear_V2_FDM (repa ired).stl
18.42 MiB 7 h 5 min 5 m 86 x 45 x 73 Download
_94_doorRearGlass_FDM (re paired).stl
2.54 MiB 1 h 12 min 1 m 73 x 30 x 5 Download
_95_doorRearGlass_X2_FDM (repaired).stl
1.76 MiB 1 h 10 min 1 m 83 x 43 x 3 Download
_96_doorRearHingePart_a_F DM (repaired).stl
0.28 MiB 9 min <1 m 7 x 16 x 9 Download
_97_doorRearHingePart_b_F DM (repaired).stl
0.55 MiB 12 min <1 m 12 x 14 x 9 Download
_98_doorRearPin_a_X2_FDM (repaired).stl
0.12 MiB 13 min <1 m 16 x 16 x 6 Download
_99_doorRearPin_b_X2_FDM (repaired).stl
0.11 MiB 8 min <1 m 18 x 8 x 5 Download
_100_hood_FDM (repaired). stl
17.27 MiB 12 h 2 min 8 m 136 x 39 x 126 Download
_101_glass_F_FDM (repaire d).stl
29.65 MiB 7 h 15 min 5 m 127 x 42 x 35 Download
_102_glass_a_L_FDM (repai red).stl
1.10 MiB 1 h 10 min 1 m 77 x 40 x 3 Download
_103_glass_b_L_FDM (repai red).stl
1.43 MiB 33 min <1 m 23 x 39 x 31 Download
_104_glass_a_R_FDM (repai red).stl
1.10 MiB 1 h 11 min 1 m 79 x 54 x 4 Download
_105_glass_b_R_FDM (repai red).stl
1.43 MiB 34 min <1 m 25 x 36 x 33 Download
_106_steeringWheel_FDM (r epaired).stl
7.86 MiB 44 min 1 m 36 x 36 x 15 Download
_107_steeringAxis_FDM (re paired).stl
0.96 MiB 15 min <1 m 95 x 55 x 3 Download
_108_pedalAccelerator_FDM (repaired).stl
0.35 MiB 32 min <1 m 21 x 14 x 23 Download
_109_pedalBrake_FDM (repa ired).stl
0.09 MiB 30 min <1 m 7 x 19 x 28 Download
_110_bumper_Rr_FDM (repai red).stl
3.63 MiB 2 h 10 min 1 m 108 x 17 x 16 Download
_111_batteryCap_V1_L_FDM (repaired).stl
0.14 MiB 41 min <1 m 66 x 20 x 4 Download
_112_batteryCap_V2_T_FDM (repaired).stl
0.53 MiB 1 h 17 min 1 m 54 x 34 x 6 Download
_113_antenna_L_FDM (repai red).stl
7.82 MiB 21 min <1 m 15 x 23 x 12 Download
_114_antenna_R_FDM (repai red).stl
7.50 MiB 26 min <1 m 10 x 10 x 28 Download
_115_battery_FDM (repaire d).stl
6.40 MiB 29 min <1 m 22 x 14 x 11 Download
_116_bumperStroboLight_X2 _FDM (repaired).stl
0.46 MiB 4 min <1 m 5 x 5 x 7 Download
_117_lightFrontGlass_V1_X 4_FDM (repaired).stl
1.98 MiB 5 min <1 m 12 x 12 x 5 Download
_118_lightFrontGlass_V2_X 4_FDM (repaired).stl
0.17 MiB 5 min <1 m 14 x 11 x 5 Download
_119_wiperSpindle_X2_FDM (repaired).stl
3.89 MiB 5 min <1 m 8 x 8 x 9 Download
_120_driverLight (repaire d).stl
7.69 MiB 14 min <1 m 12 x 12 x 13 Download
_121_mirror_L_FDM (repair ed).stl
3.40 MiB 8 min <1 m 8 x 9 x 13 Download
_122_mirror_Mid_FDM (repa ired).stl
0.74 MiB 17 min <1 m 26 x 10 x 15 Download
_123_mirror_R_FDM (repair ed).stl
4.52 MiB 15 min <1 m 11 x 15 x 20 Download
_124_hoodPin_R_FDM (repai red).stl
0.09 MiB 17 min <1 m 12 x 11 x 22 Download
_125_hoodPin_L_FDM (repai red).stl
0.07 MiB 17 min <1 m 12 x 11 x 22 Download
_126_hoodPinCover_FDM (re paired).stl
0.19 MiB 1 h 19 min 1 m 90 x 18 x 12 Download
_127_glassBlue_X5_FDM (re paired).stl
1.79 MiB 4 min <1 m 11 x 11 x 4 Download
_128_roofLamp_X4_FDM (rep aired).stl
2.18 MiB 8 min <1 m 13 x 15 x 6 Download
_129_flashingLightStand_X 2_FDM (repaired).stl
0.89 MiB 1 h 53 min 1 m 96 x 25 x 26 Download
_130_flashLightBlue_X4_FD M (repaired).stl
3.90 MiB 1 h 22 min 1 m 26 x 14 x 35 Download
_132_interiorPart_b_FDM ( repaired).stl
5.35 MiB 4 h 34 min 3 m 45 x 59 x 45 Download
_133_interiorPart_c_FDM ( repaired).stl
6.12 MiB 2 h 45 min 2 m 37 x 36 x 27 Download
_134_ghostTrap_X3_01_FDM (repaired).stl
1.82 MiB 13 min <1 m 10 x 13 x 17 Download
_135_gurney_FDM (repaired ).stl
63.09 MiB 10 h 36 min 6 m 40 x 35 x 132 Download
_136_protonPack_X4_01_FDM (repaired).stl
16.43 MiB 1 h 58 min 1 m 28 x 13 x 40 Download
_137_controllPanel_FDM (r epaired).stl
60.73 MiB 6 h 23 min 3 m 44 x 40 x 48 Download
_138_fuelTank_FDM (repair ed).stl
10.25 MiB 3 h 35 min 2 m 60 x 55 x 14 Download
_139_fuelTankCap_FDM (rep aired).stl
1.04 MiB 6 min <1 m 6 x 7 x 8 Download
_140_numberClear_X2_FDM ( repaired).stl
0.05 MiB 9 min <1 m 24 x 11 x 4 Download
_141_numberText_X2_FDM (r epaired).stl
4.15 MiB 10 min <1 m 24 x 11 x 4 Download
_142_glassStopRedCap_X2_F DM (repaired).stl
3.71 MiB 13 min <1 m 13 x 13 x 8 Download
_143_glassStopRed_X2_FDM (repaired).stl
0.23 MiB 5 min <1 m 13 x 13 x 2 Download
_144_tailStopLampPart_X4_ FDM (repaired).stl
0.29 MiB 3 min <1 m 6 x 6 x 4 Download
_145_tailStopLampRed_X4_F DM (repaired).stl
1.39 MiB 5 min <1 m 5 x 5 x 14 Download
_146_interiorLamp_FDM (re paired).stl
1.53 MiB 7 min <1 m 12 x 12 x 6 Download
_147_roofPart_a_FDM (repa ired).stl
65.26 MiB 17 h 57 min 8 m 89 x 140 x 52 Download
_148_roofPart_b_FDM (repa ired).stl
2.05 MiB 57 min 1 m 34 x 34 x 19 Download
_149_roofPart_c_FDM (repa ired).stl
0.49 MiB 49 min <1 m 13 x 8 x 48 Download
_150_roofPart_d_FDM (repa ired).stl
2.00 MiB 26 min <1 m 12 x 23 x 25 Download
_151_roofPart_e_FDM (repa ired).stl
31.23 MiB 4 h 6 min 3 m 23 x 89 x 56 Download
_152_roofPartsPin_X4_FDM (repaired).stl
0.14 MiB 3 min <1 m 3 x 3 x 12 Download
_153_lighRoofGlassRed_FDM (repaired).stl
0.18 MiB 2 min <1 m 8 x 8 x 2 Download
_154_ladder_FDM (repaired ).stl
0.07 MiB 3 h 32 min 3 m 62 x 29 x 110 Download
_155_cableConnector_FDM ( repaired).stl
0.51 MiB 6 min <1 m 12 x 9 x 8 Download
_156_pin_V1_X6_FDM (repai red).stl
0.01 MiB 4 min <1 m 5 x 10 x 5 Download
_157_pin_V2_X2_FDM (repai red).stl
0.01 MiB 15 min <1 m 21 x 14 x 7 Download
_158_pin_V3_X5_FDM (repai red).stl
0.01 MiB 14 min <1 m 16 x 25 x 4 Download
_159_bricks_V1_FDM (repai red).stl
22.41 MiB 3 h 48 min 2 m 28 x 43 x 39 Download
_160_bricks_V2_FDM (repai red).stl
22.00 MiB 3 h 33 min 2 m 31 x 43 x 40 Download
_161_bricks_V3_FDM (repai red).stl
23.32 MiB 3 h 52 min 2 m 45 x 29 x 40 Download
_162_wiper_X2_FDM (repair ed).stl
2.24 MiB 8 min <1 m 44 x 20 x 5 Download
_163_bodyPartDecor (repai red).stl
0.62 MiB 30 min <1 m 18 x 23 x 16 Download
_164_radio_FDM (repaired) .stl
2.28 MiB 22 min <1 m 17 x 20 x 11 Download
_165_waterTank_FDM (repai red).stl
0.76 MiB 19 min <1 m 18 x 14 x 12 Download
Keychain (repaired).stl
0.35 MiB 23 min <1 m 30 x 30 x 2 Download
Tag (repaired).stl
1.70 MiB 1 h 18 min 1 m 150 x 18 x 5 Download
_131_interiorPart_a_FDM ( repaired).stl
7.20 MiB 6 h 17 min 4 m 59 x 81 x 60 Download
_166_glassMatrix_a (repai red).stl
30.76 MiB 17 h 16 min 10 m 144 x 74 x 40 Download
_167_glassMatrix_b (repai red).stl
55.56 MiB 7 h 44 min 4 m 144 x 69 x 12 Download
_168_glassMatrix_c (repai red).stl
13.86 MiB 9 h 34 min 5 m 118 x 101 x 14 Download
_169_glassMatrix_d (repai red).stl
36.63 MiB 9 h 29 min 5 m 116 x 101 x 14 Download
_170_glassMatrix_e (repai red).stl
47.05 MiB 11 h 33 min 6 m 139 x 106 x 16 Download
_35_enginePart_c_R_FDM (r epaired).stl
16.02 MiB 1 h 4 min 1 m 43 x 36 x 13 Download
_36_enginePart_d_L_FDM (r epaired).stl
16.01 MiB 1 h 4 min 1 m 43 x 36 x 13 Download
_38_enginePart_f_FDM (rep aired).stl
4.33 MiB 20 min <1 m 39 x 28 x 6 Download
_34_enginePart_b_FDM (rep aired).stl
3.36 MiB 3 h 25 min 2 m 44 x 29 x 44 Download
_76 bodyPart_с_F_FDM (re paired).stl
78.27 MiB 83 h 46 min 57 m 163 x 110 x 136 Download
_171_bodyPart_g_F_FDM (re paired).stl
19.05 MiB 4 h 37 min 2 m 123 x 42 x 26 Download
...

ABOUT THIS 3D MODEL

“If there's something strange in your neighborhood, who you gonna call? Ghostbusters!”

No spook, specter, or haunt will ever be safe again thanks to the team of brave Ghostbusters! The eccentric parapsychologists, or even heroes, guard the peace of New York City using their wit and high-tech equipment. So once an emergency occurs, they jump into the flashy Ecto-1 vehicle and appear at the supernatural crime scene in a blink of an eye!

Ecto-1, so popular among fans for decades, become an object of our 3D artist’s admiration. The author based the legendary silhouette on the Miller-Meteor Futura Ambulance running on 1959 Cadillac Professional Chassis and enhanced it with various gadgets just like Dr Ray Stantz. The spacious vehicle boasts authentic active suspension, a wild-looking engine, an incredibly detailed interior, lots of warning lights and Ghostbusters’ infamous equipment for you to explore. Are you up for this ghostly challenge?

ADAPTATION FOR 3D PRINTING

Ecto-1 for 3D printing is an active assembly model and its moderation and adaptation for different types of 3D printers took the Gambody team 65 hours in total. 

For you to receive the cleanest 3D printing result possible and minimize the amount of filament needed for generated support, the craft was divided into convenient assembly parts.

All assembly parts in the FFF/FDM 1.0 version are provided in STL files in recommended positions that were worked out in order to ensure the smoothness of the details’ surfaces after printing and that the 3D printing beginners won't face difficulties when placing the parts on a build plate. When downloading any model's file you will also receive "Assembly Manual" for FFF/FDM 1.0 and DLP/SLA 1.0 versions in PDF format. We highly recommend that you get acquainted with the “Assembly video” and "Assembly Manual" before getting down to the Ecto-1 model.

The model is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.The model’s scale was calculated from the length of Ecto-1 which is approximately 7650 mm. The 3D printing model’s chosen scales are 1:16 for the FFF/FDM version and 1:32 for the DLP/SLA versions.

VERSIONS' SPECIFICATIONS

FFF/FDM 1.0 version features:

  • Contains 171 parts;
  • A printed model is 217 mm tall, 179 mm wide, 476 mm deep;
  • Incredibly detailed interior with Ghostbusters’ equipment;
  • Two options for the doors - with the Ghostbusters logo and clean;
  • Complex active suspension;
  • You can 3D print static spring plugs for the front wheels’ suspension or replace them with real springs;
  • Rotating wheels;
  • Rotating steering wheel;
  • The mechanism of the steering rack allows the simultaneous movement of the front wheels;
  • Opening doors. To open the rear passenger door, open the front door first;
  • Opening hood;
  • Authentic highly detailed engine;
  • Opening rear loading door. To open it, first pull it out and then move to the side;
  • Two options for the license plate - with the car’s name and clean;
  • The assembly of the model requires pins made out of short pieces of regular 1.75 mm filament;
  • The windows are provided as separate assembly parts to be printed using transparent material (use clear resin for the best result);
  • The tires are provided as separate assembly parts to be printed using flexible material;
  • You can create a diorama by disassembling Ecto-1 and propping it on the bricks that come included in the STL files;
  • You can introduce LED wiring to the headlights, taillights, rooftop lights, etc.; the battery can be stored inside the boxes on the rooftop and inside the car next to the left rear door;
  • All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:

  • Contains 123 parts;
  • A printed model is 108 mm tall, 90 mm wide, 238 mm deep;
  • Incredibly detailed interior with Ghostbusters’ equipment;
  • Two options for the doors - with the Ghostbusters logo and clean;
  • Static suspension;
  • Rotating wheels;
  • Rotating steering wheel;
  • Opening doors. To open the rear door, open the front door first;
  • Opening hood;
  • Authentic highly detailed engine;
  • Opening rear loading door. To open it, first pull it out and then move to the side;
  • Two options for the license plate - with the car’s name and clean;
  • The assembly of the model requires pins made out of short pieces of regular paper clips;
  • The windows are provided as separate assembly parts to be printed using transparent material;
  • You can create a diorama by disassembling Ecto-1 and propping it on the bricks that come included in the STL files;
  • You can introduce LED wiring to the headlights, taillights, rooftop lights, etc.; the battery can be stored inside the boxes on the rooftop and inside the car next to the left rear door;
  • All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

You can get the model of Ecto-1 for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Ecto-1 3D Printing Model on Gambody YouTube channel.

Also, you may like the Chevrolet Impala SS 1967 3D Printing Model, DeLorean 3D Printing Model, and other Fiction models for 3D printing.

_______

FAQ: 

Generic

Below you can find printing recommendations for CuraSimplify3DSlic3r and PrusaSlicer software.

Cura printing recommendations:

These are basic settings that were tested in Cura 4.8.0 slicer. 

The test models were printed on Ultimaker 2, Creality Ender 3, Creality CR-10S Pro V2, Anycubic I3 Mega, Anycubic I3 MegaS 3D printers with PLA and PETG filaments.

Disclaimer: The following printing settings are a recommendation, not an obligation. The parameters can vary depending on the peculiarities of your 3D printer, the material you use and especially the particular assembly part at hand. Each part that any model comprises often needs preliminary review and you are free to tweak the settings the way you find suitable.

Note:
- You can scale up the model (downscaling is not recommended!);
- All connectors should be printed at 100% Infill;
- For all parts of locks (“ge_lock” in “Source files”) you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

Quality
Layer Height: 0.12 mm (you can also set Layer Height at 0.16 or 0.2mm for 0.4mm nozzles)
Initial Layer Height: 0.2 mm (carefully level the print bed and keep your Initial Layer Height the same as the main Layer Height)

Line Width: 0.4 mm
Wall Line Width: 0.4 mm
Outer Wall Line Width: 0.4 mm
Inner Wall(s) Line Width: 0.4 mm
Top/Bottom Line Width: 0.4 mm
Infill Line Width: 0.4 mm
Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm

Initial Layer Line Width: 100%

Shell 
Wall Thickness: 0.8 mm
Wall Line Count: 2

Outer Wall Wipe Distance: 0.3 mm
Top Surface Skin Layers: 0

Top/Bottom Thickness: 0.6 mm
Top Thickness: 0.6 mm
Top Layers: 5
Bottom Thickness: 0.6 mm
Bottom Layers: 5
Initial Bottom Layers: 5

Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Optimize Wall Printing Order: Check

Compensate Wall Overlaps: Check
Compensate Inner Wall Overlaps: Check

Minimum Wall Flow: 0%
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Hole horizontal expansion: 0

Z Seam Alignment: User Specified
Z Seam Position: Back
Z Seam X: Average length of your printer’s plate (e.g.”150” if your plate is 300mm on the X-axis)
Z Seam Y: A value higher than the length of your plate on the Y-axis (e.g. 700)

Seam Corner Preference: Hide Seam
Extra Skin Wall Count: 1
Skin Overlap Percentage: 10%
Skin Overlap 0.04 mm

Infill 
Infill Density: 20% (for all smaller parts and for all parts of connectors use 100% Infill)
Infill Pattern: Triangles
Connect Infill Lines: Check
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Line Multiplier: 1
Extra Infill Wall Count: 0

Infill Overlap Percentage: 10-20%
Infill Overlap: 0.04 mm

Skin Overlap Percentage: 5%
Skin Overlap: 0.02 mm

Infill Wipe Distance: 0 mm
Infill Layer Thickness: 0.24 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2

Skin Removal Width: 0.8 mm
Top Skin Removal Width: 0.8 mm
Bottom Skin Removal Width: 0.8 mm

Skin Expand Distance: 0.8
Top Skin Expand Distance: 0.8
Bottom Skin Expand Distance: 0.8

Maximum Skin Angle for Expansion: 90˚
Minimum Skin Width for Expansion: 0.0
Skin Edge Support Thickness: 0
Skin Edge Support Layers: 0

Material 
Initial Layer Flow: 100%
Printing Temperature: See your filament settings
Initial Printing Temperature: Your filament settings
Final Printing Temperature: Your filament settings
Build Plate Temperature: Your filament settings
Build Plate Temperature Initial Layer: Your filament settings + 5°
Flow: 100% (Important! If you face difficulty printing the model, you may need to adjust the Flow parameter. You may research the topic using the Internet or seek assistance at our Customer Support Team at support@gambody.com)

Speed 

You can increase the printing Speed by 20% when you print simple objects. For small/thin parts you need to decrease the Speed by 25% - 50%.

Print Speed: 50 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 25 mm/s
          Outer Wall Speed:25 mm/s
          Inner Wall Speed: 50 mm/s

Top/Bottom Speed: 25mm/s
Support Speed: 25 mm/s 
          Support Infill Speed: 45 mm/s
          Support Interface Speed: 25 mm/s
                Support Roof Speed: 25 mm/s
                Support Floor Speed: 25 mm/s

Travel Speed: 80 mm/s
Initial Layer Speed: 80 mm/s
Initial Layer Print Speed: 20 mm/s
Initial Layer Travel Speed: 80 mm/s

Skirt/Brim Speed: 20 mm/s
Z  Hop Speed: 5 mm/s
Number of Slower Layers: 2
Enable Acceleration Control: Check

When printing simple objects, you need to set all Acceleration parameters at 500 mm/s. For small/thin parts you need to decrease the Acceleration by 50% - 70%.

Travel 
Enable Retraction: Check
Retraction Distance: 4-8 mm, 1-3 mm for Direct Extruder (This is the most important retraction parameter. You can find your optimal value of Retraction Distance by printing any test object, e.g. bridges, towers etc.)

Retraction Speed: 25mm/s
Retraction Retract Speed: 25 mm/s
Retraction Prime Speed: 25 mm/s

Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 1.5 mm
Maximum Retraction Count: 100
Minimum Extrusion Distance Window: 6,5 - 10 mm
Limit Support Retractions: Check
Combing Mode: All
Max Comb Distance With No Retract: 30 mm
Retract Before Outer Wall: Check
Avoid Printed Parts When Travelling: Check
Avoid Supports When Travelling: Check
Travel Avoid Distance: 1 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm
Z Hop When Retracted: Check
Z Hop Height: 0,3 mm

Cooling 
Enable Print Cooling: Check
Fan Speed: 100%
Regular Fan Speed: 100%
Maximum Fan Speed: 100% 

Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.36 mm
Regular Fan Speed at Layer: 3 

Minimum Layer Time: 10 s
Minimum Speed: 10 mm/s

Support 
Generate Support: Check
Support Structure: Normal (you can try using Tree Support Structure if you have difficulty printing any particular assembly part)
Support Placement: Everywhere 
Support Overhang Angle: 60° (this parameter can range from 30° to 70° depending on the part at hand)
Support Pattern: Zig Zag
Support Wall Line Count: 1 (stronger support that might be more difficult to remove) 0 (less strong support but is easier to remove)

Support Density: 15%
Support Line Distance: 2.6667 mm
Initial layer support line distance: 2.667 mm

Support Z Distance: 0.12 mm
Support Top Distance: 0.12 mm
Support Bottom Distance: 0.12 mm

Support X/Y Distance: 0.8-1 mm
Support Distance Priority: Z overrides X/Y
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Stair Step Minimum Slope Angle: 10°
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.2 mm
Gradual Support Infill Steps: 0
Minimum Support Area: 2 mm

Enable Support Interface: Check (generates additional “pillow” on the support structure that leads to a more even surface, but can be difficult to remove in hard-to-reach areas)
Enable Support Roof: Check
Enable Support Floor: Check

Support Interface Thickness: 0.8 mm
Support Roof Thickness: 0.8 mm
Support Floor Thickness: 0.8 mm

Support Interface Resolution 0.2 mm
Support Interface Density: 50-100%
        Support Roof Density: 50-100%
Support Roof Line Distance: 0.8 mm
        Support Floor Density: 50-100%
Support Floor line Distance:  0.4mm

Support Interface Pattern: Grid 
Support Roof Pattern: Grid (this parameter should differ from Bottom Pattern Initial Layer in “Shell” section)
Support Floor Pattern: Grid

Minimum Support Interface Area: 10mm
Minimum Support Roof Area: 10 mm
Minimum Support Floor Area: 10 mm

Support Interface Horizontal Expansion: 0.0 mm
Support Roof Horizontal Expansion: 0.0 mm
Support Floor Horizontal Expansion: 0.0 mm

Fan Speed Override: Check
Supported Skin Fan Speed: 100%
Use Towers: Check
Tower Diameter: 4 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Skirt/Brim (For unsteady parts, and those parts that may come unstuck use “Brim”. For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
       Brim Line Count: 10
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Experimental
Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Extruder
Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Layer
Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Additions
Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Infill
Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Support
Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Temperature
Extruder 1 Temperature: 210
Heated Bed: 60

Cooling
Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Speeds
Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Other
Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

These basic 3D printing settings recommendations for beginners were tested in Slic3r 1.3.0 software. Test models were printed on Ultimaker 2, Creality Ender 3, Creality Cr-10S pro v2, Anycubic I3 Mega, Anycubic I3 MegaS, Anycubic Vyper with PLA and PetG filaments. 

Note:

- You can upscale your 3D printing models. Downscaling is not recommended - it can make smaller parts of the model unprintable, distort the model’s level of detail and result in assembly issues. 
- All connectors should be printed at 100% Infill.
- When printing Lock connectors, we recommend setting the “Brim width” parameter to 0 in the "Skirt and Brim" print settings. In that way, the Locks will be 3D printed with a Skirt only. 

Print Settings Tab
 
Layers and perimeters
Layer height:
Layer Height: 0.1-0.2 
First layer height: 0.2-0.3
Vertical shells:
Perimeters: 2-3
Spiral vase: OFF
Horizontal shells:
Solid layers: 8 (For 0.1 Layer Height) or 4 (For 0.2 Layer Height)
Quality (slow slicing)
Extra perimeters if needed: CHECK
Avoid crossing perimeters:  CHECK
Detect thin walls: -//-
Detect bridging perimeters:  CHECK
 
Advanced: 
Seam position: Aligned
External perimeters first: -//-
 
Infill
Fill Density: 10%
Fill Pattern: Rectilinear
Top Fill Pattern: Rectilinear
Bottom fill pattern: Rectilinear
 
Reducing printing time:
Combine infill every: 1
Only infill where needed: -//-
 
Advanced:
Fill gaps: CHECK
Solid Infill every: 0
Fill angle: 45
Solid Infill threshold area: 70
Bridging angle: 0
Only retract when crossing perimeters: CHECK
Infill before perimeters: -//-
 
Skirt and brim
Skirt
Loops (minimum): 3
Distance from Object: 5
Skirt Height: 1 ( for pla and petg)
Minimal Filament extrusion length: 50
 
Brim
Brim width: (5-8 mm is optional for small prints that have bad adhesion to the build plate)
 
Support material
Support Material:
Generate Support material: -//- (enable this parameter if your model requires supports)
Overhang threshold: 40-60
Enforce support for the first: 0
 
Raft:
Raft Layers: 0
Options for Support material and Raft:
Contact Z distance: 0.2
Pattern: Rectilinear 
Pattern spacing: 2.5
Pattern angle: 0
Interface Layers: 3
Interface pattern spacing: 0.2
Support on build plate only: -//-
Don’t support bridges: CHECK
 
Speed
 
Speed for print movies
(We recommend that you try printing with the parameters listed below and then adjust the print speed until the printing quality is optimal for you)
Perimeters: 20 mm/s
Small perimeters: 20 mm/s
External perimeters: 20 mm/s
Infill: 50 mm/s
Solid: 30 mm/s
Top solid :  20 mm/s
Gaps: 20 mm/s
Bridges: 20 mm/s
Support material: 50 mm/s
 
Speed for non print movies
Travel: 100 mm/s
 
Modifiers
First layer speed: 10 mm/s
 
Acceleration control (Settings for advanced users, change these parameters only if you have sufficient 3D printing expertise)
Perimeters: 400 mm/s2
Infill: 400 mm/s2
Bridge: 400 mm/s2
First layer: 300 mm/s2
Default: 400 mm/s2
 
Auto speed (advanced)
Max print speed: 100 mm/s
Max volumetric speed: 0 mm3/s
 
Multiple Extruders
These settings only work for 3D printers with multiple extruders (not recommended for beginners)
 
Advanced
Extrusion width 
You can try setting all parameters in this section, except the First layer, to values between 0.75% of your nozzle diameter and 1.25% of your nozzle diameter. Adjusting them will help you work out the optimal parameters for the best quality for your print. As for the First layer, you can set it to 150% of the diameter of your nozzle for better adhesion to the build plate (for a nozzle with a diameter of 0.4 mm, the First layer extrusion width can be from 0.3 mm to 0.5 mm)
 
Overlap
Infill/perimeters overlap: 25%
 
Flow
Bridge flow ratio: 0.7
 
Other
-//-
Output options
-//-
Notes
-//-
Shortcuts
-//-
 
Filament Settings Tab
 
Filament
Filament
Color: -//-
Diameter: 1.75
Extrusion multiplier: 1
Density: -//-
Cost: -//-
(You can set these parameters yourself if you need)
 
Cooling
Enable
Keep fan always on: CHECK
Enable auto cooling: -//-
 
Fan settings
Fan speed
Min: 100% (for PLA, PETG) or 30% (for ABS, SBS)
Max: -//-
Bridges fan speed: 100%
Disable fan for the first: 1
 
Cooling thresholds
Enable fan if layer print time is below: -//-
Slow down if layer print time is below: -//-
Min print Speed: -//-
 
Custom G-code
-//-
Notes
-//-
 
Printer Settings Tab
 
General 
Size and coordinates
Bed shape: your 3D printer’s bed size
Z offset: 0
Capabilities
Extruders: 1
Has heated bed: CHECK
Firmware
G-code flavor: RepRap (Marlin/Sprinter)
Advanced
Use relative E distances: CHECK
 
Custom G-code
Use your 3D printer’s standard G-code. If you don't have it, you may use the example below.
Start G-code
M104 S(First_layer_temperature) 
M140  S(First_layer_bed_temperature)
G28 S(Parking)
M109 S(waiting_for_warm-up_nozzle) 
M190  S(waiting_for_warm-up_bed)
End G-code
M104 s0 ;turn off nozzle
M140 s0 ;turn off bed
G91
G1 Z1 
G28 X0 Y0 ;park
M84 ;disable motors
M107 ;disable cooling
 
Extruder 1
Size
Nozzle diameter: 0.4 mm
Layer height limits
Min: 0.05
Max: 0.3
Position
Extruder offset: -//-
Retraction
Length: 5.5-6.5 mm (1mm for a direct extruder)
Lift Z: 0-0.3 mm
Speed: 30 - 40 mm/s
Extra length on restart: 0 mm
Minimum travel after retraction: 2 mm
Retract on layer change: -//- (you can try to enable this parameter)
Wipe while retracting: -//-  (you can try to enable this parameter)
 

PrusaSlicer printing recommendations:

 
These basic 3D printing settings recommendations for beginners were tested in PrusaSlicer 2.3.1. Test models were printed on Ultimaker 2, Creality Ender 3, Creality Cr-10S pro v2, Anycubic I3 Mega, Anycubic I3 MegaS, Anycubic Vyper with PLA and PETG filaments.
 
Note:
- You can upscale your 3D printing models. Downscaling is not recommended - it can make smaller parts of the model unprintable, distort the model’s level of detail and result in assembly issues.
- All connectors should be printed at 100% Infill.
- When printing Lock connectors, we recommend setting the “Brim width” parameter to 0 in the "Skirt and Brim" print settings. In that way, the Locks will be 3D printed with a Skirt only. 
 
In order to see all the parameters listed below, you need to enable the Expert mode in the PrusaSlicer’s settings.
 
Print Settings Tab
 
Layers and perimeters
Layer height:
Layer Height: 0.1-0.2
First layer height: 0.2-0.3
Vertical shells:
Perimeters: 2-3
Spiral vase: OFF
Horizontal shells:
Solid layers: 8 (for 0.1 Layer Height) or 4 (for 0.2 Layer Height)
Minimum shell thickness: 0.8
Quality (slower slicing)
Extra perimeters if needed: CHECK
Ensure vertical shell thickness: -//-
Avoid crossing perimeters:  CHECK
Detect thin walls: -//-
Detect bridging perimeters:  CHECK
Advanced: 
Seam position: Aligned
External perimeters first: -//-
 
Infill
Infill
Fill Density: 10%
Fill Pattern: Rectilinear
Top Fill Pattern: Monotonic
Bottom fill pattern: Monotonic
Reducing printing time:
Combine infill every: 1
Only infill where needed: -//-
Advanced:
Solid Infill every: 0
Fill angle: 45
Solid Infill threshold area: 70
Bridging angle: 0
Only retract when crossing perimeters: CHECK
Infill before perimeters: -//-
 
Skirt and brim
Skirt
Loops (minimum): 3
Distance from Object: 5
Skirt Height: 1 (for PLA and PETG)
Draft Shield: -//-
Minimal filament extrusion length: 50
Brim
Brim width: (5-8 mm is optional for small prints that have bad adhesion to the build plate)
 
Support material
Support Material:
Generate Support material: -//- (enable this parameter if your model requires supports)
Auto generated supports: CHECK
Overhang threshold: 40-60
Enforce support for the first: 0
Raft:
Raft Layers: 0
Options for Support material and Raft:
Contact Z distance: 0.2
Pattern: Rectilinear 
With sheath around the support: CHECK
Pattern spacing: 2.5
Pattern angle: 0
Interface Layers: 3
Interface pattern spacing: 0.2
Interface loops: -//-
Support on build plate only: -//-
XY separation between an object and its support: 50%
Don’t support bridges: CHECK
Synchronize with object layers: -//-
 
Speed
Speed for print moves
(We recommend that you try printing with the parameters listed below and then adjust the print speed until the printing quality is optimal for you)
Perimeters: 20 mm/s
Small perimeters: 20 mm/s
External perimeters: 20 mm/s
Infill: 50 mm/s
Solid infill: 30 mm/s
Top solid infill:  20 mm/s
Support material: 50 mm/s
Support material interface: 20 mm/s
Bridges: 20 mm/s
Gap fill: 20 mm/s
Ironing: 15 mm/s
 
Speed for non-print moves
Travel: 100 mm/s
 
Modifiers
First layer speed: 10 mm/s
 
Acceleration control (Settings for advanced users, change these parameters only if you have sufficient 3D printing expertise)
Perimeters: 400 mm/s2
Infill: 400 mm/s2
Bridge: 400 mm/s2
First layer: 400 mm/s2
Default: 400 mm/s2
 
Auto speed (advanced)
Max print speed: 100 mm/s
Max volumetric speed: 0 mm3/s
 
Multiple Extruders
These settings only work for 3D printers with multiple extruders (not recommended for beginners)
 
Advanced
Extrusion width 
 
You can try setting all parameters in this section, except the First layer, to values between 0.75% of your nozzle diameter and 1.25% of your nozzle diameter. Adjusting them will help you work out the optimal parameters for the best quality for your print. As for the First layer, you can set it to 150% of the diameter of your nozzle for better adhesion to the build plate (for a nozzle with a diameter of 0.4 mm, the First layer extrusion width can be from 0.3 mm to 0.5 mm)
 
Overlap
Infill/perimeter overlap: 25%
 
Flow
Bridge flow ratio: 0.7
 
Slicing
-//-
Other
Clip multi-part objects: CHECK
Output options
-//-
Notes
-//-
Dependencies
-//-
 
Filament Settings Tab
Filament
Filament
Color: -//-
Diameter: 1.75
Extrusion multiplier: 1
Density: -//-
Cost: -//-
Spool weight: -//-
(You can set these parameters yourself if you need)
Temperature
Сheck your filament manufacturer's temperature recommendations on the spool.
 
Cooling
Enable
Keep fan always on: CHECK
Enable auto cooling: -//-
Fan settings
Fan speed
Min: 100% (for PLA, PETG) or 30% (for ABS, SBS)
Max: -//-
Bridges fan speed: 100%
Disable fan for the first: 1
Full fan speed at layer: 3-4
Cooling thresholds
Enable fan if layer print time is below: -//-
Slow down if layer print time is below: -//-
Min print speed: -//-
 
Advanced
Print speed override
Max volumetric speed:
PLA: 14 MM3/S
ABS:  10 MM3/S
PETG:  14 MM3/S
HIPS: 10 MM3/S
(If you use the Volcano extruder for your printer, all parameters need to be increased x2)
 
Filament Overrides
-//-
Custom G-code
-//-
Notes
-//-
Dependencies
-//-
 
Printer Settings Tab
 
General 
Size and coordinates
Bed shape: your 3D printer’s bed size
Max print height: your 3D printer’s height
Z offset: 0
Capabilities
Extruders: 1
Single Extruder Multi Material: -//-
Firmware
G-code flavor: RepRap/Sprinter
G-code thumbnails: -//-
Supports stealth mode: -//-
Supports remaining times: -//-
Advanced
Use relative E distances: CHECK
Use firmware retraction: -//- (needs to be enabled in the firmware of your printer)
Use volumetric E: -//-
Enable variable layer height feature: CHECK
 
Custom G-code
Use your 3D printer’s standard G-code. If you don't have it, you may use the example below.
Start G-code
M104 S(First_layer_temperature) 
M140  S(First_layer_bed_temperature)
G28 S(Parking)
M109 S(waiting_for_warm-up_nozzle) 
M190  S(waiting_for_warm-up_bed)
End G-code
M104 s0 ;turn off nozzle
M140 s0 ;turn off bed
G91
G1 Z1 
G28 X0 Y0 ;park
M84 ;disable motors
M107 ;disable cooling
 
Extruder 1
Size
Nozzle diameter: 0.4 mm
Layer height limits
Min: 0.05
Max: 0.3
Position
Extruder offset: -//-
Retraction
Length: 5.5-6.5 mm (1 mm for a direct extruder)
Lift Z: 0-0.3 mm
Retraction Speed: 30 - 40 mm/s
Deretraction Speed: 0 mm/s
Extra length on restart: 0 mm
Minimum travel after retraction: 2 mm
Retract on layer change: -//- (you can try to enable this parameter)
Wipe while retracting: -//-  (you can try to enable this parameter)
Retract amount before wipe:
Notes
-//-
Dependencies
-//-

Comments

comments powered by Disqus
avatar of Mark B
From the same author:

Reviews

  • loading reviews..

Similar items

Browse more newly listed 3D printings