Premium Stock

Metal Gear REX 3D Printing Model | Assembly + Action

(7)
cm: 39.4 w x 51 d x 40.8 h
in: 15.512 w x 20.079 d x 16.063 h

Source Files

|

Description

|

Printing Details

This 3D Model consists of files in StereoLithography (.Stl) format that is optimized for 3D printing.

Before printing the files, we strongly recommend reading the PRINTING DETAILS section.

WHAT WILL YOU GET AFTER PURCHASE?

- 2 versions of Metal Gear REX STL files for FFF/FDM and DLP/SLA/SLS - files for both versions are available for download after the purchase

- STL files of high-poly Metal Gear REX 3D Model for 3D printing consist of 221 parts- Sizes:FFF/FDM: 408 mm tall, 394 mm wide, 510 mm deep​DLP/SLA/SLS: 204 mm tall, 197 mm wide, 255 mm deepAssembly Manual for FFF/FDM 1.0 and DLP/SLA/SLS 1.0 versions in PDF format- Detailed settings that we provide as a recommendation for Cura, Simplify3D, Slic3r and PrusaSlicer for the best print- Full technical support from the Gambody Support Team

Detailed information about this 3D printing model is available in the DESCRIPTION section.

File Name File Size Time / Filament Object Size
(x/y/z mm)
_7_shin_1_R (repaired).st l
0.74 MiB 35 h 54 min 23 m 58 x 152 x 128 Download
_8_shin_2_R (repaired).st l
4.01 MiB 18 h 59 min 11 m 42 x 76 x 158 Download
_9_shin_3_R (repaired).st l
0.31 MiB 10 h 24 min 6 m 30 x 103 x 50 Download
_10_shin_4_R (repaired).s tl
0.04 MiB 1 h 57 min 1 m 57 x 28 x 20 Download
_11_shin_connector_1_R (r epaired).stl
0.24 MiB 18 min <1 m 52 x 13 x 8 Download
_12_shin_connector_2_R (r epaired).stl
0.10 MiB 24 min <1 m 30 x 29 x 10 Download
_13_shin_connector_3_R (r epaired).stl
1.62 MiB 19 min <1 m 9 x 9 x 17 Download
_14_shin_connector_4_R (r epaired).stl
1.62 MiB 20 min <1 m 9 x 9 x 17 Download
_15_shin_1_L (repaired).s tl
0.74 MiB 35 h 55 min 23 m 58 x 152 x 128 Download
_16_shin_2_L (repaired).s tl
4.01 MiB 18 h 60 min 11 m 42 x 76 x 158 Download
_17_shin_3_L (repaired).s tl
0.31 MiB 10 h 24 min 6 m 30 x 103 x 50 Download
_18_shin_4_L (repaired).s tl
0.04 MiB 1 h 57 min 1 m 57 x 28 x 20 Download
_19_shin_connector_1_L (r epaired).stl
0.24 MiB 18 min <1 m 52 x 13 x 8 Download
_20_shin_connector_2_L (r epaired).stl
0.10 MiB 24 min <1 m 30 x 29 x 10 Download
_21_shin_connector_3_L (r epaired).stl
1.62 MiB 20 min <1 m 9 x 9 x 17 Download
_22_shin_connector_4_L (r epaired).stl
1.62 MiB 20 min <1 m 9 x 9 x 17 Download
_23_finger_a_1_R (repaire d).stl
0.30 MiB 18 min <1 m 18 x 14 x 12 Download
_24_finger_a_2_R (repaire d).stl
0.08 MiB 20 min <1 m 8 x 24 x 18 Download
_25_finger_a_3_R (repaire d).stl
0.31 MiB 39 min <1 m 9 x 9 x 50 Download
_26_finger_connector_a_1_ R (repaired).stl
0.16 MiB 5 min <1 m 24 x 4 x 3 Download
_27_finger_connector_a_2_ R (repaired).stl
0.13 MiB 4 min <1 m 12 x 4 x 3 Download
_28_finger_b_1_R (repaire d).stl
0.30 MiB 17 min <1 m 18 x 14 x 12 Download
_29_finger_b_2_R (repaire d).stl
0.08 MiB 20 min <1 m 8 x 24 x 18 Download
_30_finger_b_3_R (repaire d).stl
0.31 MiB 39 min <1 m 9 x 9 x 50 Download
_31_finger_connector_b_1_ R (repaired).stl
0.16 MiB 5 min <1 m 24 x 4 x 3 Download
_32_finger_connector_b_2_ R (repaired).stl
0.13 MiB 4 min <1 m 12 x 4 x 3 Download
_33_finger_a_1_L (repaire d).stl
0.30 MiB 17 min <1 m 18 x 14 x 12 Download
_34_finger_a_2_L (repaire d).stl
0.08 MiB 20 min <1 m 8 x 24 x 18 Download
_35_finger_a_3_L (repaire d).stl
0.31 MiB 39 min <1 m 9 x 9 x 50 Download
_36_finger_connector_a_1_ L (repaired).stl
0.16 MiB 5 min <1 m 24 x 4 x 3 Download
_37_finger_connector_a_2_ L (repaired).stl
0.13 MiB 4 min <1 m 12 x 4 x 3 Download
_38_finger_b_1_L (repaire d).stl
0.30 MiB 18 min <1 m 18 x 14 x 12 Download
_39_finger_b_2_L (repaire d).stl
0.08 MiB 20 min <1 m 8 x 24 x 18 Download
_40_finger_b_3_L (repaire d).stl
0.31 MiB 39 min <1 m 9 x 9 x 50 Download
_41_finger_connector_b_1_ L (repaired).stl
0.16 MiB 5 min <1 m 24 x 4 x 3 Download
_42_finger_connector_b_2_ L (repaired).stl
0.13 MiB 4 min <1 m 12 x 4 x 3 Download
_43_rear_leg_1_R (repaire d).stl
0.35 MiB 2 h 52 min 1 m 17 x 67 x 29 Download
_44_rear_leg_2_R (repaire d).stl
0.62 MiB 10 h 40 min 7 m 33 x 52 x 110 Download
_45_rear_leg_connector_1_ R (repaired).stl
0.24 MiB 13 min <1 m 33 x 13 x 8 Download
_46_rear_leg_connector_2_ R (repaired).stl
0.24 MiB 15 min <1 m 41 x 13 x 8 Download
_47_rear_leg_1_L (repaire d).stl
0.35 MiB 2 h 52 min 1 m 17 x 67 x 29 Download
_48_rear_leg_2_L (repaire d).stl
0.62 MiB 10 h 39 min 7 m 33 x 52 x 110 Download
_49_rear_leg_connector_1_ L (repaired).stl
0.24 MiB 13 min <1 m 33 x 13 x 8 Download
_50_rear_leg_connector_2_ L (repaired).stl
0.24 MiB 15 min <1 m 41 x 13 x 8 Download
_51_leg_1_R (repaired).st l
0.56 MiB 22 h 43 min 15 m 52 x 71 x 93 Download
_52_leg_2_R (repaired).st l
0.93 MiB 25 h 54 min 15 m 53 x 75 x 114 Download
_53_leg_3_R (repaired).st l
0.58 MiB 1 h 42 min 1 m 27 x 39 x 27 Download
_54_leg_beams_R (repaired ).stl
0.02 MiB 1 h 25 min 1 m 31 x 62 x 10 Download
_55_leg_ammo_1_R (repaire d).stl
0.23 MiB 25 min <1 m 26 x 19 x 19 Download
_56_leg_ammo_2_R (repaire d).stl
0.23 MiB 26 min <1 m 27 x 14 x 19 Download
_57_leg_ammo_3_R (repaire d).stl
0.23 MiB 24 min <1 m 23 x 23 x 19 Download
_58_leg_ammo_cap_1_R (rep aired).stl
0.04 MiB 13 min <1 m 26 x 8 x 10 Download
_59_leg_ammo_cap_2_R (rep aired).stl
0.04 MiB 13 min <1 m 26 x 8 x 10 Download
_60_leg_ammo_cap_3_R (rep aired).stl
0.04 MiB 13 min <1 m 26 x 8 x 10 Download
_64_leg_1_L (repaired).st l
0.56 MiB 22 h 37 min 15 m 52 x 71 x 93 Download
_65_leg_2_L (repaired).st l
0.93 MiB 26 h 1 min 15 m 53 x 75 x 114 Download
_66_leg_3_L (repaired).st l
0.58 MiB 1 h 35 min 1 m 27 x 39 x 27 Download
_67_leg_beams_L (repaired ).stl
0.02 MiB 1 h 25 min 1 m 31 x 62 x 10 Download
_68_leg_ammo_1_L (repaire d).stl
0.23 MiB 25 min <1 m 26 x 19 x 19 Download
_69_leg_ammo_2_L (repaire d).stl
0.23 MiB 25 min <1 m 27 x 14 x 19 Download
_70_leg_ammo_3_L (repaire d).stl
0.23 MiB 24 min <1 m 23 x 23 x 19 Download
_71_leg_ammo_cap_1_L (rep aired).stl
0.04 MiB 13 min <1 m 26 x 8 x 10 Download
_72_leg_ammo_cap_2_L (rep aired).stl
0.04 MiB 13 min <1 m 26 x 8 x 10 Download
_73_leg_ammo_cap_3_L (rep aired).stl
0.04 MiB 13 min <1 m 26 x 8 x 10 Download
_77_leg_armor_R (repaired ).stl
0.34 MiB 8 h 1 min 4 m 21 x 49 x 108 Download
_81_leg_armor_L (repaired ).stl
0.34 MiB 7 h 51 min 4 m 21 x 49 x 108 Download
_85_pelvis_1 (repaired).s tl
1.34 MiB 21 h 59 min 13 m 61 x 70 x 119 Download
_86_pelvis_2 (repaired).s tl
0.32 MiB 24 h 23 min 14 m 63 x 69 x 106 Download
_87_pelvis_beams (repaire d).stl
0.02 MiB 2 h 6 min 1 m 39 x 23 x 43 Download
_88_pelvis_connector_rear _1 (repaired).stl
0.18 MiB 1 h 3 min 1 m 22 x 39 x 18 Download
_89_pelvis_connector_rear _2 (repaired).stl
0.81 MiB 9 min <1 m 18 x 14 x 9 Download
_90_pelvis_connector_rear _3 (repaired).stl
0.60 MiB 15 min <1 m 14 x 16 x 5 Download
_91_pelvis_connector_rear _4 (repaired).stl
1.73 MiB 2 h 43 min 1 m 59 x 66 x 18 Download
_92_pelvis_connector_rear _5 (repaired).stl
0.81 MiB 9 min <1 m 18 x 14 x 9 Download
_93_pelvis_connector_rear _6 (repaired).stl
0.60 MiB 15 min <1 m 14 x 16 x 5 Download
_94_pelvis_connector_rear _7 (repaired).stl
0.18 MiB 1 h 2 min 1 m 22 x 39 x 18 Download
_95_pelvis_connector_fron t_1 (repaired).stl
0.18 MiB 1 h 35 min 1 m 22 x 57 x 18 Download
_96_pelvis_connector_fron t_2 (repaired).stl
0.81 MiB 9 min <1 m 18 x 14 x 9 Download
_97_pelvis_connector_fron t_3 (repaired).stl
0.60 MiB 14 min <1 m 14 x 16 x 5 Download
_98_pelvis_connector_fron t_4 (repaired).stl
1.77 MiB 2 h 28 min 1 m 59 x 59 x 18 Download
_99_pelvis_connector_fron t_5 (repaired).stl
0.81 MiB 9 min <1 m 18 x 14 x 9 Download
_100_pelvis_connector_fro nt_6 (repaired).stl
0.60 MiB 14 min <1 m 14 x 16 x 5 Download
_104_neck_1 (repaired).st l
0.08 MiB 52 min 1 m 16 x 35 x 18 Download
_105_neck_2 (repaired).st l
0.31 MiB 1 h 8 min 1 m 16 x 35 x 18 Download
_106_pelvis_gun_1 (repair ed).stl
1.02 MiB 3 min <1 m 6 x 15 x 3 Download
_107_pelvis_gun_2 (repair ed).stl
0.09 MiB 16 min <1 m 18 x 20 x 7 Download
_108_pelvis_gun_3 (repair ed).stl
0.47 MiB 7 min <1 m 12 x 11 x 3 Download
_109_pelvis_gun_4 (repair ed).stl
0.87 MiB 37 min <1 m 20 x 20 x 18 Download
_110_pelvis_gun_5 (repair ed).stl
0.86 MiB 18 min <1 m 12 x 24 x 12 Download
_111_pelvis_gun_6 (repair ed).stl
1.49 MiB 17 min <1 m 12 x 12 x 14 Download
_112_pelvis_gun_7 (repair ed).stl
0.17 MiB 1 h 30 min 1 m 17 x 15 x 46 Download
_113_arm_1_R (repaired).s tl
0.40 MiB 35 h 37 min 22 m 62 x 88 x 171 Download
_114_arm_2_R (repaired).s tl
0.20 MiB 2 h 4 min 1 m 20 x 20 x 55 Download
_115_arm_rail_gun_a_1_R ( repaired).stl
0.07 MiB 2 h 40 min 2 m 20 x 145 x 10 Download
_116_arm_rail_gun_a_2_R ( repaired).stl
0.06 MiB 3 h 27 min 2 m 23 x 146 x 11 Download
_117_arm_rail_gun_a_3_R ( repaired).stl
0.01 MiB 15 min <1 m 13 x 34 x 3 Download
_118_arm_rail_gun_a_4_R ( repaired).stl
0.45 MiB 1 h 31 min 1 m 167 x 167 x 2 Download
_119_arm_rail_gun_b_1_R ( repaired).stl
0.07 MiB 2 h 41 min 2 m 20 x 145 x 10 Download
_120_arm_rail_gun_b_2_R ( repaired).stl
0.06 MiB 3 h 27 min 2 m 23 x 146 x 11 Download
_121_arm_rail_gun_b_3_R ( repaired).stl
0.01 MiB 15 min <1 m 13 x 34 x 3 Download
_122_arm_rail_gun_b_4_R ( repaired).stl
0.45 MiB 1 h 31 min 1 m 167 x 167 x 2 Download
_128_arm_1_L (repaired).s tl
0.22 MiB 1 h 21 min 1 m 57 x 57 x 4 Download
_129_arm_2_L (repaired).s tl
0.85 MiB 10 h 26 min 5 m 95 x 92 x 62 Download
_130_arm_3_L (repaired).s tl
0.16 MiB 1 h 40 min 1 m 25 x 8 x 75 Download
_131_arm_4_L (repaired).s tl
0.53 MiB 9 h 47 min 6 m 43 x 58 x 89 Download
_132_arm_5_L (repaired).s tl
0.01 MiB 19 min <1 m 15 x 49 x 3 Download
_138_body_R (repaired).st l
2.00 MiB 51 h 45 min 31 m 206 x 71 x 69 Download
_139_body_L (repaired).st l
2.00 MiB 51 h 39 min 31 m 206 x 71 x 69 Download
_140_body_cap_1_R (repair ed).stl
0.04 MiB 13 min <1 m 26 x 8 x 10 Download
_141_body_cap_2_R (repair ed).stl
0.04 MiB 13 min <1 m 26 x 8 x 10 Download
_142_body_cap_3_R (repair ed).stl
0.04 MiB 13 min <1 m 26 x 8 x 10 Download
_143_body_cap_4_R (repair ed).stl
0.04 MiB 13 min <1 m 26 x 8 x 10 Download
_144_body_cap_1_L (repair ed).stl
0.04 MiB 13 min <1 m 26 x 8 x 10 Download
_145_body_cap_2_L (repair ed).stl
0.04 MiB 13 min <1 m 26 x 8 x 10 Download
_146_body_cap_3_L (repair ed).stl
0.04 MiB 13 min <1 m 26 x 8 x 10 Download
_147_body_cap_4_L (repair ed).stl
0.04 MiB 13 min <1 m 26 x 8 x 10 Download
_148_head (repaired).stl
2.03 MiB 35 h 32 min 22 m 74 x 54 x 182 Download
_149_head_R (repaired).st l
2.66 MiB 22 h 1 min 15 m 65 x 71 x 79 Download
_150_head_L (repaired).st l
2.66 MiB 21 h 44 min 15 m 65 x 71 x 79 Download
_151_head_cap (repaired). stl
0.06 MiB 1 h 39 min 1 m 45 x 38 x 9 Download
_152_head_grid (repaired) .stl
1.04 MiB 1 h 36 min 1 m 127 x 13 x 14 Download
_153_jaw_connector_1 (rep aired).stl
0.52 MiB 30 min <1 m 11 x 37 x 13 Download
_154_jaw_connector_2 (rep aired).stl
0.58 MiB 5 min <1 m 9 x 10 x 4 Download
_155_jaw_connector_3 (rep aired).stl
0.77 MiB 4 min <1 m 11 x 13 x 4 Download
_156_jaw_connector_4 (rep aired).stl
0.25 MiB 31 min <1 m 26 x 36 x 13 Download
_157_jaw (repaired).stl
0.26 MiB 12 h 58 min 9 m 62 x 39 x 118 Download
_158_cockpit (repaired).s tl
0.45 MiB 4 h 21 min 2 m 39 x 68 x 41 Download
_159_Ge_lock_10H_x60 (rep aired).stl
0.03 MiB 4 min <1 m 18 x 10 x 2 Download
_160_pilot_split (repaire d).stl
50.13 MiB 1 h 14 min 1 m 17 x 19 x 41 Download
_161_pilot_body (repaired ).stl
21.93 MiB 35 min <1 m 17 x 19 x 21 Download
_162_pilot_head (repaired ).stl
13.88 MiB 5 min <1 m 6 x 8 x 9 Download
_163_pilot_leg_L (repaire d).stl
2.78 MiB 13 min <1 m 7 x 14 x 17 Download
_164_pilot_leg_R (repaire d).stl
4.12 MiB 12 min <1 m 7 x 10 x 18 Download
_165_pilot_arm_R (repaire d).stl
4.15 MiB 7 min <1 m 4 x 15 x 10 Download
_166_pilot_arm_L (repaire d).stl
3.99 MiB 7 min <1 m 5 x 15 x 10 Download
Keychain (repaired).stl
0.35 MiB 23 min <1 m 30 x 30 x 2 Download
Tag (repaired).stl
1.70 MiB 1 h 18 min 1 m 150 x 18 x 5 Download
_1_foot_R (repaired).stl
1.72 MiB 2 h 8 min 1 m 32 x 57 x 15 Download
_2_foot_connector_1_R (re paired).stl
2.22 MiB 29 min <1 m 25 x 24 x 8 Download
_3_foot_connector_2_R (re paired).stl
0.82 MiB 47 min <1 m 15 x 12 x 51 Download
_4_foot_L (repaired).stl
1.72 MiB 2 h 8 min 1 m 32 x 57 x 15 Download
_5_foot_connector_1_L (re paired).stl
2.22 MiB 29 min <1 m 25 x 24 x 8 Download
_6_foot_connector_2_L (re paired).stl
0.82 MiB 47 min <1 m 15 x 12 x 51 Download
_61_leg_connector_1_R (re paired).stl
2.33 MiB 55 min 1 m 33 x 32 x 10 Download
_62_leg_connector_2_R (re paired).stl
0.82 MiB 1 h 28 min 1 m 16 x 19 x 79 Download
_63_leg_connector_3_R (re paired).stl
1.99 MiB 1 h 29 min 1 m 27 x 27 x 24 Download
_74_leg_connector_1_L (re paired).stl
2.33 MiB 55 min 1 m 33 x 32 x 10 Download
_75_leg_connector_2_L (re paired).stl
0.82 MiB 1 h 28 min 1 m 16 x 19 x 79 Download
_76_leg_connector_3_L (re paired).stl
1.99 MiB 1 h 29 min 1 m 27 x 27 x 24 Download
_78_leg_armor_connector_1 _R (repaired).stl
2.16 MiB 43 min <1 m 19 x 19 x 17 Download
_79_leg_armor_connector_2 _R (repaired).stl
0.64 MiB 32 min <1 m 11 x 14 x 34 Download
_80_leg_armor_connector_3 _R (repaired).stl
2.23 MiB 25 min <1 m 24 x 23 x 7 Download
_82_leg_armor_connector_1 _L (repaired).stl
2.16 MiB 43 min <1 m 19 x 19 x 17 Download
_83_leg_armor_connector_2 _L (repaired).stl
0.64 MiB 32 min <1 m 11 x 14 x 34 Download
_84_leg_armor_connector_3 _L (repaired).stl
2.23 MiB 25 min <1 m 24 x 23 x 7 Download
_102_pelvis_connector_fro nt_8 (repaired).stl
2.36 MiB 53 min 1 m 33 x 32 x 10 Download
_103_pelvis_connector_fro nt_9 (repaired).stl
2.09 MiB 1 h 29 min 1 m 27 x 27 x 24 Download
_123_arm_connector_1_R (r epaired).stl
2.10 MiB 1 h 29 min 1 m 27 x 27 x 24 Download
_124_arm_connector_2_R (r epaired).stl
2.36 MiB 53 min 1 m 33 x 32 x 10 Download
_125_1_arm_connector_3_R (repaired).stl
0.28 MiB 1 h 52 min 1 m 13 x 25 x 66 Download
_125_2_arm_connector_3_R (repaired).stl
0.88 MiB 26 min <1 m 16 x 19 x 17 Download
_125_3_arm_connector_3_R. stl
0.88 MiB 28 min <1 m 16 x 19 x 17 Download
_126_arm_connector_4_R (r epaired).stl
2.36 MiB 48 min <1 m 33 x 32 x 10 Download
_127_arm_connector_5_R (r epaired).stl
2.10 MiB 1 h 21 min 1 m 27 x 27 x 24 Download
_133_arm_connector_1_L (r epaired).stl
2.10 MiB 1 h 29 min 1 m 27 x 27 x 24 Download
_134_arm_connector_2_L (r epaired).stl
2.36 MiB 53 min 1 m 33 x 32 x 10 Download
_135_1_arm_connector_3_L (repaired).stl
0.28 MiB 1 h 53 min 1 m 13 x 25 x 66 Download
_135_2_arm_connector_3_L (repaired).stl
0.88 MiB 26 min <1 m 16 x 19 x 17 Download
_135_3_arm_connector_3_L (repaired).stl
0.88 MiB 28 min <1 m 16 x 19 x 17 Download
_136_arm_connector_4_L (r epaired).stl
2.36 MiB 48 min <1 m 33 x 32 x 10 Download
_137_arm_connector_5_L (r epaired).stl
2.10 MiB 1 h 21 min 1 m 27 x 27 x 24 Download
_101_1_pelvis_connector_f ront_7 (repaired).stl
0.32 MiB 51 min 1 m 22 x 42 x 18 Download
_101_2_pelvis_connector_f ront_7 (repaired).stl
1.18 MiB 34 min <1 m 19 x 18 x 19 Download
...

ABOUT THIS 3D MODEL

REX is a Metal Gear prototype that was designed as a nuclear-capable bipedal tank reinforced with near-impenetrable compound armour. The all-terrain battle mecha comes from the Metal Gear series of action stealth video games by the legendary Hideo Kojima.

Metal Gear Rex model for 3D printing was brought to you by our contributing 3D artist who has been enthusiastic about the unusual bipedal tank and the Metal Gear franchise on the whole for quite a while now. The bulky 3D printing walking battle tank is heavily armed with rotary cannons, anti-tank missiles, a free-electron laser cannon, and a powerful magnetic rail gun. Inside the cockpit of the mecha defence machine, you will also find a miniature of its pilot, the Big Boss, who together with the REX will make for an impressive addition to any Metal Gear display!

ADAPTATION FOR 3D PRINTING

Metal Gear REX for 3D printing is an active assembly model and its moderation and adaptation for different types of 3D printers took the Gambody team 45 hours in total. 

For you to receive the cleanest 3D printing result possible and to minimize the amount of filament needed for generated support the bipedal tank model was divided into many assembly parts, and special mechanisms were introduced into all model’s movable elements to give you an opportunity to display REX in a variety of positions and scenes.

All assembly parts are provided in STL files in recommended positions that were worked out in order to ensure the smoothness of the details’ surfaces after printing and that the 3D printing beginners won't face difficulties when placing the parts on a build plate. When downloading any model's file you will also receive "Assembly Manual" for FFF/FDM 1.0 and DLP/SLA/SLS 1.0 versions in PDF format. We highly recommend that you get acquainted with the “Assembly video” and "Assembly Manual" before getting down to the Metal Gear REX model.

The model is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.

The model's scale was calculated from the approximate height of the Metal Gear REX which is 13000 mm. The 3D printing model's chosen scale is 1:32 for the FFF/FDM version and 1:64 for the DLP/SLA/SLS version.

VERSIONS' SPECIFICATIONS

FFF/FDM 1.0 version features:- Contains 167 parts;- A printed model is 408 mm tall, 394 mm wide, 510 mm deep;- REX’s beak-like cockpit opens to reveal a highly detailed interior and Big Boss behind the controls;- There is a spot inside REX’s head where you can hide the battery and LED wiring and light up the cockpit and forward-facing missiles;- 360° movement of the head and body is ensured by an extendable double ratchet mechanism in the “neck”, and a ball joint;- Opening hatches on the body and legs reveal missiles;- Double ball joint mechanism with tightening nut allows 360° rotation of the shoulders;- Ball joint mechanism with tightening nut allows the rotation of the hip;- 360° rotation of the leg armour via ball joint mechanism with tightening nut;- The pelvis laser cannon can be articulated via a ratchet;- The “shins” are retractable, there are stoppers inside the retractable shins and tightening screws for rigidity adjustment;- The “knee” can go up via a ratchet and it can be fixed in a raised position;- 360° rotation of the feet via ball joint mechanism with tightening nut;- The driving stakes (claws) are articulated;- Rear stabilisation controls (heels) are articulated via two ratchets and can be fully folded;- REX’s assembly requires additional "pins" that can be made out of short pieces of regular 1.75mm filament;- All parts are divided in such a way that you will print them with the smallest number of support structures.

DLP/SLA 1.0 version features:- Contains 54 parts;- A printed model is 204 mm tall, 197 mm wide, 255 mm deep;- REX’s beak-like cockpit opens to reveal Big Boss behind the controls;- There is a spot inside REX’s head where you can hide the battery and LED wiring and light up the cockpit;- Opening hatches on the body and legs reveal missiles;- REX’s neck, shoulders, hips, pelvis laser, leg armour, driving stakes (claws), feet, and rear stabilisation controls (heels), move via simple cylinder connectors;- REX’s assembly requires additional "pins" that can be made out of short pieces of a regular paperclip;- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.

You can get the model of Metal Gear REX for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.

Watch the tutorial on how to assemble Metal Gear REX 3D Printing Model at Gambody YouTube channel.

Also, you may like Big Boss 3D Printing Figurine, as well as other Robot 3D Printing Models.

_______FAQ: Where can I print a model if I have no printer?How to get started with 3D printing?How to set up my 3D printer?How to choose right 3D model print bed positioning? How to paint printed figurine?

Generic

Below you can find printing recommendations for CuraSimplify3DSlic3r and PrusaSlicer software.

Cura printing recommendations:

These are basic settings that were tested in Cura 4.8.0 slicer. 

The test models were printed on Ultimaker 2, Creality Ender 3, Creality CR-10S Pro V2, Anycubic I3 Mega, Anycubic I3 MegaS 3D printers with PLA and PETG filaments.

Disclaimer: The following printing settings are a recommendation, not an obligation. The parameters can vary depending on the peculiarities of your 3D printer, the material you use and especially the particular assembly part at hand. Each part that any model comprises often needs preliminary review and you are free to tweak the settings the way you find suitable.

Note:
- You can scale up the model (downscaling is not recommended!);
- All connectors should be printed at 100% Infill;
- For all parts of locks (“ge_lock” in “Source files”) you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.

Quality
Layer Height: 0.12 mm (you can also set Layer Height at 0.16 or 0.2mm for 0.4mm nozzles)
Initial Layer Height: 0.2 mm (carefully level the print bed and keep your Initial Layer Height the same as the main Layer Height)

Line Width: 0.4 mm
Wall Line Width: 0.4 mm
Outer Wall Line Width: 0.4 mm
Inner Wall(s) Line Width: 0.4 mm
Top/Bottom Line Width: 0.4 mm
Infill Line Width: 0.4 mm
Skirt/Brim Line Width: 0.4 mm
Support Line Width: 0.4 mm

Initial Layer Line Width: 100%

Shell 
Wall Thickness: 0.8 mm
Wall Line Count: 2

Outer Wall Wipe Distance: 0.3 mm
Top Surface Skin Layers: 0

Top/Bottom Thickness: 0.6 mm
Top Thickness: 0.6 mm
Top Layers: 5
Bottom Thickness: 0.6 mm
Bottom Layers: 5
Initial Bottom Layers: 5

Top/Bottom Pattern: Lines
Bottom Pattern Initial Layer: Lines
Top/Bottom Line Directions: [ ]
Outer Wall Inset: 0 mm
Optimize Wall Printing Order: Check

Compensate Wall Overlaps: Check
Compensate Inner Wall Overlaps: Check

Minimum Wall Flow: 0%
Fill Gaps Between Walls: Everywhere
Filter Out Tiny Gaps: Check
Horizontal Expansion: 0 mm
Initial Layer Horizontal Expansion: 0 mm
Hole horizontal expansion: 0

Z Seam Alignment: User Specified
Z Seam Position: Back
Z Seam X: Average length of your printer’s plate (e.g.”150” if your plate is 300mm on the X-axis)
Z Seam Y: A value higher than the length of your plate on the Y-axis (e.g. 700)

Seam Corner Preference: Hide Seam
Extra Skin Wall Count: 1
Skin Overlap Percentage: 10%
Skin Overlap 0.04 mm

Infill 
Infill Density: 20% (for all smaller parts and for all parts of connectors use 100% Infill)
Infill Pattern: Triangles
Connect Infill Lines: Check
Infill Line Directions: [ ]
Infill X Offset: 0 mm
Infill Y Offset: 0 mm
Infill Line Multiplier: 1
Extra Infill Wall Count: 0

Infill Overlap Percentage: 10-20%
Infill Overlap: 0.04 mm

Skin Overlap Percentage: 5%
Skin Overlap: 0.02 mm

Infill Wipe Distance: 0 mm
Infill Layer Thickness: 0.24 mm
Gradual Infill Steps: 0
Infill Before Walls: Check
Minimum Infill Area: 0 mm2

Skin Removal Width: 0.8 mm
Top Skin Removal Width: 0.8 mm
Bottom Skin Removal Width: 0.8 mm

Skin Expand Distance: 0.8
Top Skin Expand Distance: 0.8
Bottom Skin Expand Distance: 0.8

Maximum Skin Angle for Expansion: 90˚
Minimum Skin Width for Expansion: 0.0
Skin Edge Support Thickness: 0
Skin Edge Support Layers: 0

Material 
Initial Layer Flow: 100%
Printing Temperature: See your filament settings
Initial Printing Temperature: Your filament settings
Final Printing Temperature: Your filament settings
Build Plate Temperature: Your filament settings
Build Plate Temperature Initial Layer: Your filament settings + 5°
Flow: 100% (Important! If you face difficulty printing the model, you may need to adjust the Flow parameter. You may research the topic using the Internet or seek assistance at our Customer Support Team at support@gambody.com)

Speed 

You can increase the printing Speed by 20% when you print simple objects. For small/thin parts you need to decrease the Speed by 25% - 50%.

Print Speed: 50 mm/s
    Infill Speed: 50 mm/s
    Wall Speed: 25 mm/s
          Outer Wall Speed:25 mm/s
          Inner Wall Speed: 50 mm/s

Top/Bottom Speed: 25mm/s
Support Speed: 25 mm/s 
          Support Infill Speed: 45 mm/s
          Support Interface Speed: 25 mm/s
                Support Roof Speed: 25 mm/s
                Support Floor Speed: 25 mm/s

Travel Speed: 80 mm/s
Initial Layer Speed: 80 mm/s
Initial Layer Print Speed: 20 mm/s
Initial Layer Travel Speed: 80 mm/s

Skirt/Brim Speed: 20 mm/s
Z  Hop Speed: 5 mm/s
Number of Slower Layers: 2
Enable Acceleration Control: Check

When printing simple objects, you need to set all Acceleration parameters at 500 mm/s. For small/thin parts you need to decrease the Acceleration by 50% - 70%.

Travel 
Enable Retraction: Check
Retraction Distance: 4-8 mm, 1-3 mm for Direct Extruder (This is the most important retraction parameter. You can find your optimal value of Retraction Distance by printing any test object, e.g. bridges, towers etc.)

Retraction Speed: 25mm/s
Retraction Retract Speed: 25 mm/s
Retraction Prime Speed: 25 mm/s

Retraction Extra Prime Amount: 0 mm3 
Retraction Minimum Travel: 1.5 mm
Maximum Retraction Count: 100
Minimum Extrusion Distance Window: 6,5 - 10 mm
Limit Support Retractions: Check
Combing Mode: All
Max Comb Distance With No Retract: 30 mm
Retract Before Outer Wall: Check
Avoid Printed Parts When Travelling: Check
Avoid Supports When Travelling: Check
Travel Avoid Distance: 1 mm
Layer Start X: 0.0 mm
Layer Start Y: 0.0 mm
Z Hop When Retracted: Check
Z Hop Height: 0,3 mm

Cooling 
Enable Print Cooling: Check
Fan Speed: 100%
Regular Fan Speed: 100%
Maximum Fan Speed: 100% 

Regular/Maximum Fan Speed Threshold: 10 s
Initial Fan Speed: 0%
Regular Fan Speed at Height: 0.36 mm
Regular Fan Speed at Layer: 3 

Minimum Layer Time: 10 s
Minimum Speed: 10 mm/s

Support 
Generate Support: Check
Support Structure: Normal (you can try using Tree Support Structure if you have difficulty printing any particular assembly part)
Support Placement: Everywhere 
Support Overhang Angle: 60° (this parameter can range from 30° to 70° depending on the part at hand)
Support Pattern: Zig Zag
Support Wall Line Count: 1 (stronger support that might be more difficult to remove) 0 (less strong support but is easier to remove)

Support Density: 15%
Support Line Distance: 2.6667 mm
Initial layer support line distance: 2.667 mm

Support Z Distance: 0.12 mm
Support Top Distance: 0.12 mm
Support Bottom Distance: 0.12 mm

Support X/Y Distance: 0.8-1 mm
Support Distance Priority: Z overrides X/Y
Support Stair Step Height: 0.3 mm
Support Stair Step Maximum Width: 5.0 mm
Support Stair Step Minimum Slope Angle: 10°
Support Join Distance: 2.0 mm
Support Horizontal Expansion: 0.2 mm
Support Infill Layer Thickness: 0.2 mm
Gradual Support Infill Steps: 0
Minimum Support Area: 2 mm

Enable Support Interface: Check (generates additional “pillow” on the support structure that leads to a more even surface, but can be difficult to remove in hard-to-reach areas)
Enable Support Roof: Check
Enable Support Floor: Check

Support Interface Thickness: 0.8 mm
Support Roof Thickness: 0.8 mm
Support Floor Thickness: 0.8 mm

Support Interface Resolution 0.2 mm
Support Interface Density: 50-100%
        Support Roof Density: 50-100%
Support Roof Line Distance: 0.8 mm
        Support Floor Density: 50-100%
Support Floor line Distance:  0.4mm

Support Interface Pattern: Grid 
Support Roof Pattern: Grid (this parameter should differ from Bottom Pattern Initial Layer in “Shell” section)
Support Floor Pattern: Grid

Minimum Support Interface Area: 10mm
Minimum Support Roof Area: 10 mm
Minimum Support Floor Area: 10 mm

Support Interface Horizontal Expansion: 0.0 mm
Support Roof Horizontal Expansion: 0.0 mm
Support Floor Horizontal Expansion: 0.0 mm

Fan Speed Override: Check
Supported Skin Fan Speed: 100%
Use Towers: Check
Tower Diameter: 4 mm
Minimum Diameter: 3.0 mm
Tower Roof Angle: 65° 

Build Plate Adhesion 
Build Plate Adhesion Type: Skirt/Brim (For unsteady parts, and those parts that may come unstuck use “Brim”. For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")
Skirt/Brim Minimum Length: 250 mm
Brim Width: 8.0 mm
       Brim Line Count: 10
Brim Only on Outside: Check

Mesh Fixes 
Union Overlapping Volumes: Check
Merged Meshes Overlap: 0.15 mm

Special Modes
Print Sequence: All at Once
Surface Mode: Normal

Experimental
Slicing Tolerance: Middle
Maximum Resolution: 0.01 mm
Flow rate compensation max extrusion offset: 0 mm
Flow rate compensation factor: 100%

Simplify3D printing recommendations:

This model was tested with PLA material.

To avoid printing problems, we recommend the following settings:

Extruder
Nozzle Diameter: 0.4 mm
Extrusion Multiplier: 0.97
Extrusion Width: Auto

Retraction Distance: 5.00 mm
Extra Restart Distance: 0.00 mm
Retraction Vertical Lift: 0.08 mm
Retraction Speed: 5400.0 mm/min

Wipe Distance: 5.00 mm

Layer
Primary Layer Height: 0.2 mm
Top Solid Layers: 8
Bottom Solid Layers: 5
Outline/Perimeter Shells: 2
Outline Direction: Inside-Out

First Layer Height: 90%
First Layer Width: 100%
First Layer Speed: 20%

Additions
Use Skirt/Brim: Check
Skirt Layers: 1
Skirt Offset from Part: 6.00 mm
Skirt Outlines: 5

Infill
Internal Fill Pattern: Fast Honeycomb
External Fill Patern: Rectilinear
Interior Fill Percentage: 10%
Outline Overlap: 22%
Infill Extrusion Width: 100%
Minimum Infill Length: 5.00 mm
Combine Infill Every: 1 layers

External Infill Angle Offsets: 45/-45 deg

Support
Generate Support Material: Check
Support Infill Percentage: 15%
Extra Inflation Distance: 1.00 mm
Support Base Layers: 0
Combine Support Every: 1 layers

Dense Support Layers: 0
Dense Infill Percentage: 70%

Support Type: Normal
Support Pillar Resolution: 5.00 mm
Max Overhang Angle: 60 deg

Horizontal Offset From Part: 0.50 mm
Upper Vertical Separation Layers: 1
Lower Vertical Separation Layers: 1

Support Infill Angles: 45 deg

Temperature
Extruder 1 Temperature: 210
Heated Bed: 60

Cooling
Increase fan speed for layers below: 45.0 sec
  Maximum Cooling fan speed: 50%
Bridging fan speed override: 100%

Speeds
Default Printing Speed: 4800.0 mm/min
Outline Underspeed: 50%
Solid Infill Underspeed: 80%
Support Structure Underspeed: 80%
X/Y Axis Movement Speed: 10800.0 mm/min
Z Axis Movemen Speed: 1002.0 mm/min

Adjust printing speed for layers below: 15.0 sec 
  Allow speed reduction down to: 20%

Other
Unsupported area threshold: 20.0 sq m

Slic3r printing recommendations:

These basic 3D printing settings recommendations for beginners were tested in Slic3r 1.3.0 software. Test models were printed on Ultimaker 2, Creality Ender 3, Creality Cr-10S pro v2, Anycubic I3 Mega, Anycubic I3 MegaS, Anycubic Vyper with PLA and PetG filaments. 

Note:

- You can upscale your 3D printing models. Downscaling is not recommended - it can make smaller parts of the model unprintable, distort the model’s level of detail and result in assembly issues. 
- All connectors should be printed at 100% Infill.
- When printing Lock connectors, we recommend setting the “Brim width” parameter to 0 in the "Skirt and Brim" print settings. In that way, the Locks will be 3D printed with a Skirt only. 

Print Settings Tab
 
Layers and perimeters
Layer height:
Layer Height: 0.1-0.2 
First layer height: 0.2-0.3
Vertical shells:
Perimeters: 2-3
Spiral vase: OFF
Horizontal shells:
Solid layers: 8 (For 0.1 Layer Height) or 4 (For 0.2 Layer Height)
Quality (slow slicing)
Extra perimeters if needed: CHECK
Avoid crossing perimeters:  CHECK
Detect thin walls: -//-
Detect bridging perimeters:  CHECK
 
Advanced: 
Seam position: Aligned
External perimeters first: -//-
 
Infill
Fill Density: 10%
Fill Pattern: Rectilinear
Top Fill Pattern: Rectilinear
Bottom fill pattern: Rectilinear
 
Reducing printing time:
Combine infill every: 1
Only infill where needed: -//-
 
Advanced:
Fill gaps: CHECK
Solid Infill every: 0
Fill angle: 45
Solid Infill threshold area: 70
Bridging angle: 0
Only retract when crossing perimeters: CHECK
Infill before perimeters: -//-
 
Skirt and brim
Skirt
Loops (minimum): 3
Distance from Object: 5
Skirt Height: 1 ( for pla and petg)
Minimal Filament extrusion length: 50
 
Brim
Brim width: (5-8 mm is optional for small prints that have bad adhesion to the build plate)
 
Support material
Support Material:
Generate Support material: -//- (enable this parameter if your model requires supports)
Overhang threshold: 40-60
Enforce support for the first: 0
 
Raft:
Raft Layers: 0
Options for Support material and Raft:
Contact Z distance: 0.2
Pattern: Rectilinear 
Pattern spacing: 2.5
Pattern angle: 0
Interface Layers: 3
Interface pattern spacing: 0.2
Support on build plate only: -//-
Don’t support bridges: CHECK
 
Speed
 
Speed for print movies
(We recommend that you try printing with the parameters listed below and then adjust the print speed until the printing quality is optimal for you)
Perimeters: 20 mm/s
Small perimeters: 20 mm/s
External perimeters: 20 mm/s
Infill: 50 mm/s
Solid: 30 mm/s
Top solid :  20 mm/s
Gaps: 20 mm/s
Bridges: 20 mm/s
Support material: 50 mm/s
 
Speed for non print movies
Travel: 100 mm/s
 
Modifiers
First layer speed: 10 mm/s
 
Acceleration control (Settings for advanced users, change these parameters only if you have sufficient 3D printing expertise)
Perimeters: 400 mm/s2
Infill: 400 mm/s2
Bridge: 400 mm/s2
First layer: 300 mm/s2
Default: 400 mm/s2
 
Auto speed (advanced)
Max print speed: 100 mm/s
Max volumetric speed: 0 mm3/s
 
Multiple Extruders
These settings only work for 3D printers with multiple extruders (not recommended for beginners)
 
Advanced
Extrusion width 
You can try setting all parameters in this section, except the First layer, to values between 0.75% of your nozzle diameter and 1.25% of your nozzle diameter. Adjusting them will help you work out the optimal parameters for the best quality for your print. As for the First layer, you can set it to 150% of the diameter of your nozzle for better adhesion to the build plate (for a nozzle with a diameter of 0.4 mm, the First layer extrusion width can be from 0.3 mm to 0.5 mm)
 
Overlap
Infill/perimeters overlap: 25%
 
Flow
Bridge flow ratio: 0.7
 
Other
-//-
Output options
-//-
Notes
-//-
Shortcuts
-//-
 
Filament Settings Tab
 
Filament
Filament
Color: -//-
Diameter: 1.75
Extrusion multiplier: 1
Density: -//-
Cost: -//-
(You can set these parameters yourself if you need)
 
Cooling
Enable
Keep fan always on: CHECK
Enable auto cooling: -//-
 
Fan settings
Fan speed
Min: 100% (for PLA, PETG) or 30% (for ABS, SBS)
Max: -//-
Bridges fan speed: 100%
Disable fan for the first: 1
 
Cooling thresholds
Enable fan if layer print time is below: -//-
Slow down if layer print time is below: -//-
Min print Speed: -//-
 
Custom G-code
-//-
Notes
-//-
 
Printer Settings Tab
 
General 
Size and coordinates
Bed shape: your 3D printer’s bed size
Z offset: 0
Capabilities
Extruders: 1
Has heated bed: CHECK
Firmware
G-code flavor: RepRap (Marlin/Sprinter)
Advanced
Use relative E distances: CHECK
 
Custom G-code
Use your 3D printer’s standard G-code. If you don't have it, you may use the example below.
Start G-code
M104 S(First_layer_temperature) 
M140  S(First_layer_bed_temperature)
G28 S(Parking)
M109 S(waiting_for_warm-up_nozzle) 
M190  S(waiting_for_warm-up_bed)
End G-code
M104 s0 ;turn off nozzle
M140 s0 ;turn off bed
G91
G1 Z1 
G28 X0 Y0 ;park
M84 ;disable motors
M107 ;disable cooling
 
Extruder 1
Size
Nozzle diameter: 0.4 mm
Layer height limits
Min: 0.05
Max: 0.3
Position
Extruder offset: -//-
Retraction
Length: 5.5-6.5 mm (1mm for a direct extruder)
Lift Z: 0-0.3 mm
Speed: 30 - 40 mm/s
Extra length on restart: 0 mm
Minimum travel after retraction: 2 mm
Retract on layer change: -//- (you can try to enable this parameter)
Wipe while retracting: -//-  (you can try to enable this parameter)
 

PrusaSlicer printing recommendations:

 
These basic 3D printing settings recommendations for beginners were tested in PrusaSlicer 2.3.1. Test models were printed on Ultimaker 2, Creality Ender 3, Creality Cr-10S pro v2, Anycubic I3 Mega, Anycubic I3 MegaS, Anycubic Vyper with PLA and PETG filaments.
 
Note:
- You can upscale your 3D printing models. Downscaling is not recommended - it can make smaller parts of the model unprintable, distort the model’s level of detail and result in assembly issues.
- All connectors should be printed at 100% Infill.
- When printing Lock connectors, we recommend setting the “Brim width” parameter to 0 in the "Skirt and Brim" print settings. In that way, the Locks will be 3D printed with a Skirt only. 
 
In order to see all the parameters listed below, you need to enable the Expert mode in the PrusaSlicer’s settings.
 
Print Settings Tab
 
Layers and perimeters
Layer height:
Layer Height: 0.1-0.2
First layer height: 0.2-0.3
Vertical shells:
Perimeters: 2-3
Spiral vase: OFF
Horizontal shells:
Solid layers: 8 (for 0.1 Layer Height) or 4 (for 0.2 Layer Height)
Minimum shell thickness: 0.8
Quality (slower slicing)
Extra perimeters if needed: CHECK
Ensure vertical shell thickness: -//-
Avoid crossing perimeters:  CHECK
Detect thin walls: -//-
Detect bridging perimeters:  CHECK
Advanced: 
Seam position: Aligned
External perimeters first: -//-
 
Infill
Infill
Fill Density: 10%
Fill Pattern: Rectilinear
Top Fill Pattern: Monotonic
Bottom fill pattern: Monotonic
Reducing printing time:
Combine infill every: 1
Only infill where needed: -//-
Advanced:
Solid Infill every: 0
Fill angle: 45
Solid Infill threshold area: 70
Bridging angle: 0
Only retract when crossing perimeters: CHECK
Infill before perimeters: -//-
 
Skirt and brim
Skirt
Loops (minimum): 3
Distance from Object: 5
Skirt Height: 1 (for PLA and PETG)
Draft Shield: -//-
Minimal filament extrusion length: 50
Brim
Brim width: (5-8 mm is optional for small prints that have bad adhesion to the build plate)
 
Support material
Support Material:
Generate Support material: -//- (enable this parameter if your model requires supports)
Auto generated supports: CHECK
Overhang threshold: 40-60
Enforce support for the first: 0
Raft:
Raft Layers: 0
Options for Support material and Raft:
Contact Z distance: 0.2
Pattern: Rectilinear 
With sheath around the support: CHECK
Pattern spacing: 2.5
Pattern angle: 0
Interface Layers: 3
Interface pattern spacing: 0.2
Interface loops: -//-
Support on build plate only: -//-
XY separation between an object and its support: 50%
Don’t support bridges: CHECK
Synchronize with object layers: -//-
 
Speed
Speed for print moves
(We recommend that you try printing with the parameters listed below and then adjust the print speed until the printing quality is optimal for you)
Perimeters: 20 mm/s
Small perimeters: 20 mm/s
External perimeters: 20 mm/s
Infill: 50 mm/s
Solid infill: 30 mm/s
Top solid infill:  20 mm/s
Support material: 50 mm/s
Support material interface: 20 mm/s
Bridges: 20 mm/s
Gap fill: 20 mm/s
Ironing: 15 mm/s
 
Speed for non-print moves
Travel: 100 mm/s
 
Modifiers
First layer speed: 10 mm/s
 
Acceleration control (Settings for advanced users, change these parameters only if you have sufficient 3D printing expertise)
Perimeters: 400 mm/s2
Infill: 400 mm/s2
Bridge: 400 mm/s2
First layer: 400 mm/s2
Default: 400 mm/s2
 
Auto speed (advanced)
Max print speed: 100 mm/s
Max volumetric speed: 0 mm3/s
 
Multiple Extruders
These settings only work for 3D printers with multiple extruders (not recommended for beginners)
 
Advanced
Extrusion width 
 
You can try setting all parameters in this section, except the First layer, to values between 0.75% of your nozzle diameter and 1.25% of your nozzle diameter. Adjusting them will help you work out the optimal parameters for the best quality for your print. As for the First layer, you can set it to 150% of the diameter of your nozzle for better adhesion to the build plate (for a nozzle with a diameter of 0.4 mm, the First layer extrusion width can be from 0.3 mm to 0.5 mm)
 
Overlap
Infill/perimeter overlap: 25%
 
Flow
Bridge flow ratio: 0.7
 
Slicing
-//-
Other
Clip multi-part objects: CHECK
Output options
-//-
Notes
-//-
Dependencies
-//-
 
Filament Settings Tab
Filament
Filament
Color: -//-
Diameter: 1.75
Extrusion multiplier: 1
Density: -//-
Cost: -//-
Spool weight: -//-
(You can set these parameters yourself if you need)
Temperature
Сheck your filament manufacturer's temperature recommendations on the spool.
 
Cooling
Enable
Keep fan always on: CHECK
Enable auto cooling: -//-
Fan settings
Fan speed
Min: 100% (for PLA, PETG) or 30% (for ABS, SBS)
Max: -//-
Bridges fan speed: 100%
Disable fan for the first: 1
Full fan speed at layer: 3-4
Cooling thresholds
Enable fan if layer print time is below: -//-
Slow down if layer print time is below: -//-
Min print speed: -//-
 
Advanced
Print speed override
Max volumetric speed:
PLA: 14 MM3/S
ABS:  10 MM3/S
PETG:  14 MM3/S
HIPS: 10 MM3/S
(If you use the Volcano extruder for your printer, all parameters need to be increased x2)
 
Filament Overrides
-//-
Custom G-code
-//-
Notes
-//-
Dependencies
-//-
 
Printer Settings Tab
 
General 
Size and coordinates
Bed shape: your 3D printer’s bed size
Max print height: your 3D printer’s height
Z offset: 0
Capabilities
Extruders: 1
Single Extruder Multi Material: -//-
Firmware
G-code flavor: RepRap/Sprinter
G-code thumbnails: -//-
Supports stealth mode: -//-
Supports remaining times: -//-
Advanced
Use relative E distances: CHECK
Use firmware retraction: -//- (needs to be enabled in the firmware of your printer)
Use volumetric E: -//-
Enable variable layer height feature: CHECK
 
Custom G-code
Use your 3D printer’s standard G-code. If you don't have it, you may use the example below.
Start G-code
M104 S(First_layer_temperature) 
M140  S(First_layer_bed_temperature)
G28 S(Parking)
M109 S(waiting_for_warm-up_nozzle) 
M190  S(waiting_for_warm-up_bed)
End G-code
M104 s0 ;turn off nozzle
M140 s0 ;turn off bed
G91
G1 Z1 
G28 X0 Y0 ;park
M84 ;disable motors
M107 ;disable cooling
 
Extruder 1
Size
Nozzle diameter: 0.4 mm
Layer height limits
Min: 0.05
Max: 0.3
Position
Extruder offset: -//-
Retraction
Length: 5.5-6.5 mm (1 mm for a direct extruder)
Lift Z: 0-0.3 mm
Retraction Speed: 30 - 40 mm/s
Deretraction Speed: 0 mm/s
Extra length on restart: 0 mm
Minimum travel after retraction: 2 mm
Retract on layer change: -//- (you can try to enable this parameter)
Wipe while retracting: -//-  (you can try to enable this parameter)
Retract amount before wipe:
Notes
-//-
Dependencies
-//-

Comments

comments powered by Disqus

Similar items

Browse more newly listed 3D printings